Product#: 3415

Bumper Bolt with Conical Keps Hex Nut; Polished Stainless Steel Capped Head; 3/4" Diameter; 3/8-16" x 1"; Zinc Plated

Reproduction GM bumper bolt for a variety of General Motors and Chrysler applications. Each zinc-plated steel carriage bolt features a polished stainless steel cap for superb cosmetic appearance, corrosion resistance and long...


Product#: 2710

Chrome Trim Screw, #8 x 3/4", With #8 Phillips Oval Head

Replacement chrome plated trim screws used on various GM vehicles. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is original...


Product#: 8610

Flat Washer; 1/2" USS; Zinc Plated

1/2" USS zinc plated Flat Washer for a variety of applications. A washer is a thin plate (typically disk-shaped) with a hole (typically in the middle) that is normally used to distribute the load of a threaded fastener, such...


Product#: 13757

1965-69 Impala, Camaro, Bel Air, Firebird; Hood Insulation Fastener; Black Nylon

Replacement black nylon 2" square head hood insulation retainer is just what your classic vehicle needs to keep your original hood insulation where it belongs...attached to the hood. This retainer is a service replacement for...


Product#: 10362

Bolt, 5/16-18 x 13/16" Pointed Tip With Hex Washer Head, Black Phosphate

OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. Note: For a money saving set of 10 use...


Product#: 3899508

1959-80 Trico Windshield Wiper Blade; 15" Length; Various Models; Each

Reproduction 15 inch "TRICO Style # PR-15-2W" wiper blade for a wide variety of classic vehicle models. Each blade features stainless steel construction and is loaded with a period-correct TRICO RF-15 style insert with a...


Product#: CX1172

1947-72 Chevrolet/GMC Truck Outer Door Mirror Arm Mounting Screw Set

OER® reproduction 3 piece stainless steel screw set for mounting the outer door side mirror arms on 1947-72 Chevrolet and GMC trucks. One set per mirror arm required. Note: Not for use on 1970-72 door mirror assemblies....


Product#: DW4235G

1947-53 GM Truck 1 Piece Custom Windshield Glass with Seal - Green Tint with Blue Shade

Replace the outdated 2-piece windshield in your 1947-53 truck with a one-piece windshield manufactured utilizing molded laminate safety glass. To install this glass, you must cut out the center divider bar that your truck was...


Product#: DW4235T

1947-53 GM Truck 1 Piece Custom Windshield Glass With Seal - Tinted

Replace the outdated 2-piece windshield in your 1947-53 truck with a one-piece windshield manufactured utilizing molded laminate safety glass. To install this glass, you must cut out the center divider bar that your truck was...


Product#: DW4235Y

1947-54 GM Truck 1 Piece Windshield Glass with Seal - Gray Tinted

Replace the outdated 2-piece windshield in your 1947-53 truck with a one-piece windshield manufactured utilizing molded laminate safety glass. To install this glass, you must cut out the center divider bar that your truck was...


Product#: DW4235C

1947-53 GM Truck 1 Piece Custom Windshield Glass with Seal - Clear

Replace the outdated 2-piece windshield in your 1947-53 truck with a one-piece windshield manufactured utilizing molded laminate safety glass. To install this glass, you must cut out the center divider bar that your truck was...


Product#: 14117

1947-53 Chevy, GMC Pickup Truck; Hood Latch Panel; Stainless Steel; Mirror Chrome Finish

Reproduction hood latch panel for 1947-54 Chevrolet, GMC pickup truck models. Each hood latch panel is manufactured to OE specifications in stainless steel with a bright mirror chrome plated finish for a custom appearance....


Product#: K51020

1962-76 GM, Dodge, Plymouth; Various Models; Convertible Top Boot Storage Bag

Why leave your top boot in the trunk exposed when you can keep it safe and clean by safely storing it in this special top boot storage bag. The storage bag will help protect your vehicles top boot while being stored in the...


Product#: 14849T

1951-55 Chevrolet, GMC Truck, Vent Window Assembly; with Chrome Division Bar; Tinted Glass; LH

Reproduction of the original door vent window assembly for 1951-55 Chevrolet and GMC truck models. Each glass assembly is manufactured to OE specifications replicating the original in quality, fitment, and design. This vent...


Product#: 14850T

1951-55 Chevrolet, GMC Truck, Vent Window Assembly; with Chrome Division Bar; Tinted Glass; RH

Reproduction of the original door vent window assembly for 1951-1955 Chevrolet and GMC truck models. Each glass assembly is manufactured to OE specifications replicating the original in quality, fitment, and design. This vent...


Product#: 14845T

1951-55 Chevrolet, GMC Truck, Vent Window Assembly; with Black Division Bar; Tinted Glass; RH

Reproduction of the original door vent window assembly for 1951-55 Chevrolet and GMC truck models. Each glass assembly is manufactured to OE specifications replicating the original in quality, fitment, and design. This vent...


Product#: 11503957

U-Nut; M6 - 1.0; Panel Range.030" to.160"; Center of Hole to Edge: 17/32"; Black Phosphate; Each

Black phosphate metric u-nut or foldover nut, that measures M6-1.0 to install and secure various components. Fits panel thickness from.80mm to 4 mm. (.030" to.160") Specifications: OE #: 11503957 Quantity: Individual Clip...


Product#: CX1146

1947-72 Chevrolet/GMC Truck; Round Door Mirror Head; Chrome; Smooth Backing

Reproduction exterior round mirror head for 1947-72 Chevrolet & GMC truck models. This reproduction mirror head is design to replace the worn out or missing original. Features a chrome backing with a 5" smooth, non-ribbed...


Product#: 14855

1949-1955 Chevrolet, GMC Truck; Door Window Frame Molding; Stainless Steel; LH & RH

Reproduction of the original exterior window frames designed for use with 1949-55 Chevrolet and GMC truck models. Each frame is manufactured in stamped stainless steel to exact factory specifications replicating the original...


Product#: A1017

3/8"-16 x 15/16" Bumper Bolt With Flat; Zinc Plated Shank; Stainless Steel Flat Head; Each

Correct replacement style bolt to replace the original missing or damaged bumper bolt. Each bolt is manufactured to original specifications and will match the original. Fits a variety of different years and models. Measures...