1956 Chevrolet Nomad Parts - Controls

This super compact, easy-to-mount, 3-knob control panel delivers valuable control at your fingertips. The individual switches can be removed from the pod and mounted directly into your dash for increased design options and...

Replacement U-clip nuts used on various GM vehicles. Black phosphate coated. Quantities vary by model. Use as needed. Heater control fastener clip is designed to replace the damaged or missing originals for the heater...

Reproduction of the original deluxe heater shaft and spring set for 1955-56 Chevrolet Bel Air, 150, 210, and Nomad models. Includes 1 pin, 1 spring, 1 retaining clip and 2 washers. These heavily sought pieces are now...

This straight-tab retainer clip for 1955-56 Chevrolet passenger car models is used to hold the heater cable in place.

This control panel delivers infinite louver air temperature regulation and bi-level operation of A/C and heat. With simple plug-in connections no vacuum lines and fewer wires to route the panel operates our exclusive...

Combine low and high pressure clutch cut-off functions and electric fan engaugement signal at 254 psi. The low pressure cut-off of these trinary switches is 30 psi and the high pressure cut-off is 406psi.

Maximize your system with this improved switch featuring a rear harness set up that allows the resistor to be attached in the rear of controls.

These reproduction vent and defrost control cables are cosmetically correct and fully functional. Features ribbed knobs as original for 1956 models. Controls defrost and passenger side vents.

Reproduction of the original heater control levers designed for use with 1956 Chevrolet Bel Air, 150, 210, and Nomad models. Each lever is manufactured to correct factory specifications replicating the original in design and...

Reproduction of the original deluxe heater indicator metal backing plate designed for use with 1955-56 Chevrolet Bel Air, 150, 210, and Nomad models. Each plate is manufactured in stamped steel to factory specifications.

These poly covered cables with Polyethylene lining provide reduced resistance, maximum flexibility and instant response even during severe weather conditions. Note: The outer shell can be removed to create an orig inal...

These reproduction clips are used to connect the heater cables to the heater and vent assembly. Set includes screws.

Replacement push on round flat nuts used on various vehicles. Zinc plated. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is...

Replacement push on round flat nuts used on various vehicles. Zinc plated. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is...

Gen II Streamline 4-knob control panel with black anodized finish from Vintage Air. This control panel is designed to fit into very compact dash or console positions. It is internally lighted through the soft-glow aluminum...

Combine low and high pressure clutch cut-off functions and electric fan engaugement signal at 254 psi. The low pressure cut-off of these trinary switches is 30 psi and the high pressure cut-off is 406psi.

Reproduction of the heater control bezel for all 1955-56 models equipped with a factory heater. Manufactured with a bright chrome finish as original.

Replacement push on round flat nuts used on various vehicles. Zinc plated. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is...

Reproduction of the original deluxe heater control knobs designed for use with 1955-59 Chevrolet and GMC trucks with a deluxe heater control assembly. models. Each knob is reproduced to exact factory dimensions offering a...

Vintage Air trinary switch kit for beadlock crimp hoses. Vintage Air trinary swithes feature low and high pressure compressor clutch cut-off functions plus an electric fan engagement signal at 254 psi. The low pressure...

Dual fan wiring harness with the proper gauge and color coordinated wire, temperature sending unit, waterproof 40 amp relays and 30 amp fuse with holder. Includes installation guide and detailed diagrams. Can be used on any...

Replacement push on round flat nuts used on various vehicles. Zinc plated. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is...