1956 Chevrolet Nomad Parts - Fuel System

Reproduction fuel filler hose to connect fuel neck to fuel tank on a variety of models requiring a 2" ID fuel hose. This hose can be used as is, or if you require a shorter piece, you can cut this 18" fuel hose to your...

This throttle cable is designed with a specially extruded liner to extend the life of the cable. Cables are equipped with aluminum fittings and aluminum ferrule to eliminate fraying. Clevis is designed to eliminate cotter...

Correct style rod clip used on various GM vehicles. Fits 1/4" rod diameter, RH, 17/64" ID. These reproduction transmission linkage rod clips need to be replaced when replacing your linkage rods. 1955-57 Chevrolet...

Reproduction of the original fuel tank designed for use with 1955-56 Chevy Bel Air, 150, 210, Station wagon and Nomad models (except 9 passenger models). This reproduction tank is manufactured in quality zinc coated steel and...

Reproduction fuel tank for 1955-56 wagon, Nomad and sedan delivery station wagon models (except 9-passenger). This reproduction tank is manufactured to factory specifications in Niterne steel. Note: Shipped double...

This externally-mounted electric fuel pump is ideal for most street and strip applications. Proven rotary vein technology provides high flow and stable pressures with minimal vibration and sound. Each pump features 3/8"...

Reproduction set of the original 2-1/2" flat blade carburetor fuel bowl screws for Holley carburetors. These special screws are specifically designed in the correct original configuration with the proper head design for the...

OER® reproduction of the original accelerator rod grommet and sleeve unit where the accelerator rod fits into the linkage. This grommet often deteriorates due to engine heat or chemical spillage. Replacing the grommet will...

This universal anti-squeak insulator set includes two rubber strips that insert in between the gas tank and the mounting straps to eliminate any noise from tank movement and vibration which may occur. One foam rubber pad...

Universal style accelerator throttle rod designed for use on various GM, Ford, Chrysler, Dodge, Plymouth models. This accelerator rod is for use when modifications will not allow the use of the original rod between the...

Universal fuel tank sending unit for various GM and other models that require a 90 ohm sender. Designed for use with OE or aftermarket 0-90 ohm gauges, each sending unit includes the sender, float, float rod, hardware,...

Universal style anti squeak cushions are designed to install between the gas tank and the gas tank straps. These fuel tank anti squeek pads cushion the gas tank from the body and straps to reduce noise caused by metal to...

This throttle cable is designed with a specially extruded liner to extend the life of the cable. Cables are equipped with aluminum fittings and aluminum ferrule to eliminate fraying. Clevis is designed to eliminate cotter...

Reproduction fuel tank mounting straps for 1955-57 wagon models. Produced using heavy duty zinc-plated material with all correct contours for an authentic fit and appearance.Approximate strap measurement bend to bend is - 32...

Reproduction of the original style fuel tank anti squeek set designed specifically for vehicle models. Includes one 5-1/4" x 2" x 1/2" precision die cut neoprene tank to floor cushion, two 24" x 1-1/4" molded rubber strap...

This externally-mounted electric fuel pump is ideal for most street and strip applications. Proven rotary vein technology provides high flow and stable pressures with minimal vibration and sound. Each pump features 3/8"...

Reproduction of the original clips used to mount the fuel line to the frame. Includes six 3/8" clips. Applications: 1967-69 Chevrolet Camaro - Big Block 1967-69 Chevrolet Camaro - Small Block w/4bbl 1965-86...

Reproduction of the original fuel tank sending unit designed for use with 1955-57 Chevrolet Bel Air, 150, 210, station wagon, and Nomad models. Don't run out of fuel because of a defective sending unit. Replace that old worn...

Reproduction fuel tank mounting straps for 1955-57 Chevrolet Bel Air station wagon models. Produced using stainless steel material with all correct contours for an authentic fit and appearance. Approximate strap measurement...

Universal fuel tank sending unit for various GM and other models that require a 30 ohm sender. Designed for use with OE or aftermarket 0-30 ohm gauges, each sending unit includes the sender, float, float rod, hardware,...

Reproduction brass fuel sending unit float for various 1947-76 General Motors, and Chrysler, Dodge, Plymouth models. If your fuel gauge isn't reading correctly, it may be the fuel sending unit float. The original OE float may...

Die-cut reproduction air cleaner to carburetor gasket manufactured for use with any 2 bbl or 4 bbl carburator with a 5-1/8" base. Can be used with any small or big block engine. Fits most 1964 and newer Ford applications,...

Reproduction of the original style fuel sending unit and filler neck O-ring designed for use with 1955-1957 Chevrolet Bel Air, 150, 210, and Nomad models. This O-ring is manufactured to correct factory dimensions and replaces...

Edelbrock Pro-Flo 4 EFI System for 1986 & Earlier Small-Block Chevy engines. The EFI system comes with a 4150-Style satin finish single plane intake manifold and 35 Lb/Hr injectors capable of 550 HP with 58 p.s.i. fuel...

FiTech Fuel Injection Retro LS EFI system. The Retro LS EFI 650hp fuel injection system offers transmission control and are suitable for everything from your junkyard 5.3 to a Stroker 427. They deliver old-school carburetor...

The Go EFI 4 Self Tuning Fuel Injection is rated at up to 600 HP and is suitable for engines from 250 HP thru 600 HP. It fits any 4-bbl intake manifold and is the most self-contained and full-featured unit of this type. It...

The FiTech Meanstreet offers an onboard ECU and fuel pressure regulator to bring the user simple, clean wiring, and an easy install. It fits any 4-bbl intake manifold and is the most self-contained and full-featured unit of...