1956 Chevrolet Nomad Parts - Tools

The Auto Rotisserie E-Z Spin features 12 multi-angle postioning stops every 30 degrees, HD swivel casters and rotates a full 360 degrees. It's work height is adjustable from 44" to 59", center line is adjustable from 10" to...

Measure the weight of your car with this quality vehicle scale. This scale features weight for each wheel as well as total weight. Percentage weight is also available as well as front and rear percentages. Each of the...

This 1200 lbs weight capacity fold-up engine stand is a tremendous improvement over traditional designs. When in use, it allows the engine to tilt upwards, simplifying post-crankshaft installation operations such as painting...

PROFORM's new billet aluminum 1000 lb digital bench top spring tester is the most accurate way to check spring pressure. Check springs up to 1.9in diameter and 3 7/8in height. Digital display reads in 1 lb (0.5 kg)...

Portable, hands-free alignment can be done quickly and easily with the fast trax & trade; adjustable camber/caster gauge. This tool will help you fine-tune your alignment for optimal tracking and handling, while minimizing...

Race Ramps are ideal for low ground clearance vehicles with tires up to 10" wide. With an incline of only 10.75°, they lift your car 10" and can hold up to 3,000lbs per set and weigh only 10lbs per ramp. Like all Race...

Race Ramps are ideal for low ground clearance vehicles with tires up to 10" wide. With an incline of only 10.75°, they lift your car 10" and can hold up to 3,000lbs per set and weigh only 10lbs per ramp. Like all Race...

Is your trailer door too high up to get your classic to the race track or autocross? Are you tired of busting up your vehicle's nose just getting in and out of the trailer? Race Ramps has just the solution for you! Simply...

Race Ramps are ideal for low ground clearance vehicles with tires up to 10" wide. With an incline of only 10.75°, they lift your car 8" and can hold up to 3,000lbs per set and weigh only 10lbs per ramp. Like all Race...

Portable, hands-free alignment can be done quickly and easily with the FasTrax™ Adjustable Camber/Caster Gauge. This tool will help you fine-tune your alignment for optimal tracking and handling, while minimizing tire...

This product helps to prevent your tires from flat-spotting during long periods of storage. Once the tires are set in the FlatStoppers (on a level surface), they will settle into the pad's concave depression. More of the...

Race Ramps are ideal for low ground clearance vehicles with tires up to 10" wide. With an incline of only 10.75 degrees, they lift your car 8" and can hold up to 3,000lbs per set and weigh only 10lbs per ramp. Like all...

For the serious engine rebuilder who wants to be sure that the engine is balanced correctly. We now offer several scales depending on the accuracy requirements.

H3R Performance HalGuard? Halotron® 1 premium clean agent fire extinguisher. This ultra compact 1.4 lb. hand held extinguisher features a black powder coated steel cylinder and all metal valve construction that is passed,...

Working in a kneeling position on concrete takes a heavy toll on your body, especially your knees, back, feet and legs! This new tool approaches working on your knees in a whole new way! Instead of supporting yourself on...

This adjustable heavy-duty spring compressor, designed for the cylinder head expert is loaded with new premium features: reinforced compression-hold handle, reinforced adjustable arm with dual locking pins, box steel...

This easy to use electric ring filer makes quick and precise work of ring grinding. Square up your ring by simply pressing it against the dowel pins for a clean grind. Includes a standard 120 volt adapter that works well in...

H3R Performance MaxOut? dry chemical fire extinguishers. These compact 2.5 lb. extinguishers are perfect for undo-dash or seat mounting and the chrome finish will not fade like anodized units on the market will. Dry chemical...

Portable, hands-free alignment can be done quickly and easily with the FasTrax™ Adjustable Camber/Caster Gauge. This tool will help you fine-tune your alignment for optimal tracking and handling, while minimizing tire...

Here's the affordable, portable way to test springs. The hex-design body is very versatile: use it in a vise or an arbor press. The device is designed to test valve spring pressure ranging from zero to 700 pounds (or 318 kgs)...

Holcutters are not hole saws. They are precision ground, heat treated tools that easily cut through the stock rather than ripping, tearing, and pushing thru as do typical hole saws. They can produce holes 3 times faster...

Our heavy-duty cylinder head work stand is a great way to hold your cylinder heads above your workbench while working on them. The adjustable arms allow you to set the proper height and maintain stability.

H3R Performance MaxOut? dry chemical fire extinguishers. These compact 2.5 lb. extinguishers are perfect for undo-dash or seat mounting and the glossy black finish will not fade like anodized units on the market will. Dry...

The auto hood puller is designed for easy pulling and mounting of the hood. Helps to eliminate scratches and dings to the paint on the hood and fenders. To be used with any engine pulling hoist.

Designed with proven features from the renowned Mityvac pumps, this Professional Model Automotive Kit delivers both vacuum and pressure. The dual capability of the new Mityvac® hand pump combines two pumps into one. It...

If you think your project vehicle is about to become a permanent fixture where it sits, we have a solution for you. These new auto dollys are just the trick for a simple way of moving your restoration project around with...

This set contains all the tools needed to degree cams in most popular engines, assuring proper timing and lift. Set includes: 9" degree wheel Dial indicator and mount 2 valve check springs Clamp kit 14mm top dead...

This heavy-duty, simple-to-use, manual valve spring compressor makes short work of even monstrous springs. The compressor arm slides for adjustment, employing a locking pin for rapid, easy operation.

H3R Performance MaxOut? dry chemical fire extinguishers. These compact 2.5 lb. extinguishers are perfect for undo-dash or seat mounting and the fire engine red finish will not fade like anodized units on the market will. Dry...

This important tool makes installing the lower distributor drive shaft bushing into the engine block and subsequent reaming a snap. Simply tighten down to install the bushing, and spin the tool on the way out for a clean...

Affordable AN hex wrenches. Color coded for fast identification, these wrenches offer resistance to scratching hose fittings as they are being tightened and loosened. 8 piece set includes: 1/2" 9/16" 11/16" 13/16" 1" ...

The Rolling Rack turns 1 of your Auto Dollies into a convenient transport rack. Works with all Auto Dolly sizes. Made in USA Note: Auto Dollies not included.

If you think your project vehicle is about to become a permanent fixture where it sits, we have a solution for you. These new auto dollys are just the trick for a simple way of moving your restoration project around with...

Here's the affordable, portable way to test springs. The hex-design body is very versatile: use it in a vise or an arbor press. These hydraulic models are supplied with a rubber gauge protector.

Works with all Ford, GM and Chrysler engines. This heavy-duty, professional tool, equipped with roller thrust bearings, can also be used as a universal puller! Includes 7/16"-20, 5/8"-18, and 3/4"-16 adapters and various...

To test the quality of a paint job the Pro Gauge can't be beat! Basically, it's a device which measures paint thickness. Factory paint is usually four to five mils in thickness (a mil is one thousandth of an inch). By...

For precision hole making in sheet metal and frame materials up to 1/4" thick, Rotabroach® annular cutters make clean, burr-free, round holes with no deforming of stock or damage to the surrounding material. Ideal for...

Here's the affordable, portable way to test springs. The hex-design body is very versatile: use it in a vise or an arbor press. These hydraulic models are supplied with a rubber gauge protector.

Billet aluminum band clamps for H3R Performance 1 and 1.4 lb fire extinguishers. These brushed clamps combine with H3R?s flat surface mount to create a quick release mounting assembly for 2.5 lb. H3R fire extinguishers. They...

Checking the spark in relation to the piston ensures that your engine is firing as efficiently as possible. The Tac-Style Shift Light from PROFORM allows you to check timing, help diagnose a no-spark condition and check for...

Color coded, affordable A N Hex wrench set. These lightweight, billet aluminum, wrenches are perfect for tightening those expensive aluminum fittings without marring them. Micro CNC detailing, and soft touch anodizing make...

Holcutter™ is not hole saw. It is precision ground, heat treated tool that easily cuts through the stock rather than ripping, tearing, and pushing thru as do typical hole saws. The Holecutter™ can produce holes...

A quick adapter to attach the FasTrax? to wheels without an outer ?lip?. Fits on the SP91000, SP91010 and SP91025.

PROFORM's steel multiple attachment point, LS engine lift plate makes getting the engine out a cinch. Simply remove the intake manifold and valley tray cover, then replace it with this robust lift plate using the existing...

These Proform AN adjustable wrenches are constructed from billet aluminum and are easy to adjust. They're the perfect non-marring tools for under hood plumbing work. This is a blue anodized adjustable crescent wrench that...

This fork set is designed to separate ball joints, tie rods, pitman arms and other suspension items that are difficult to separate.

Range: 1.600" to 2.100". Measure installed valve spring height conveniently and accurately. Simply install the height micrometer instead of a valve spring, and then rotate the clearly engraved dial to expand the tool to seat...

This Rotabroach® set is for rustproofing and cutting access holes. Rotabroach® Cutters are for precision hole making in sheet metal, frame materials, and plate stock up to 1/2" thick, whether Mild Steel,...

For precision hole making in sheet metal and frame materials up to 1/4" thick, Rotabroach® annular cutters make clean, burr-free, round holes with no deforming of stock or damage to the surrounding material. Ideal for...

This Rotabroach® set is for cutting access holes, fabrication, removing spot welds and body work. Rotabroach® Cutters are for precision hole making in sheet metal, frame materials, and plate stock up to 1/2"...

This Rotabroach® set is for rustproofing and cutting access holes. Rotabroach® Cutters are for precision holemaking in sheet metal, frame materials, and plate stock up to 1/2" thick, whether Mild Steel, Stainless...

After cutting out rusted areas on fenders or quarter panels, preparing the panels with an offset flange will produce a clean, flush fit. The wide jaws work into corners and saves time on straightaways. Work on up to 18...

The pistol grip ratcheting action and the fast acting plunger compress disc brake pistons in seconds. This makes brake pad replacement a snap.

For precision hole making in sheet metal and frame materials up to 1/4" thick, Rotabroach® annular cutters make clean, burr-free, round holes with no deforming of stock or damage to the surrounding material. Made in...

For precision hole making in sheet metal and frame materials up to 1/4" thick, Rotabroach® annular cutters make clean, burr-free, round holes with no deforming of stock or damage to the surrounding material. Made in...