Product#: ST016

1955-72 Buick, Chevy, Pontiac, Oldsmobile, Full Size; Convertible Top Hydraulic Pump Seal Set

Hydraulic pump seal set designed for use with the various 1955-72 GM Full Size convertible models listed. This set contains 2 large O-rings. Depending on the year of your car, only 1 may be required. These large O-rings seal...


Product#: 14914

1955-72 Camaro, Firebird, Impala, Nova; Convertible Top Hose Retainer; Push In Style

Reproduction of the original hose retainer clip designed for use with 1967-69 GM convertible models. Each clip is manufactured in stamped steel and heat treated for extra strength. This clip is designed to retain the...


Product#: 153078

1967-69 Camaro, Firebird; Convertible Top Boot Interior Snaps with Screws; 4 Piece Set

Reproduction convertible top boot snap and screw set for 1967-69 Camaro and Firebird models and any other vehicle that requires a screw-on style snap. These snaps are used to secure the convertible top to the inner rear...


Product#: HK237

1955-62 Buick, Cadillac, Chevrolet, Pontiac, Oldsmobile; Convertible Top Motor And Pump Assembly; Various Models

Reproduction convertible top motor & pump assembly made to provide consistent hydraulic pressure and dependability. Raise and lower the power top with ease by replacing the old or worn out original. The motor comes complete...


Product#: TF400955

1955-57 Bel Air, Bonnevelle, Catalina, Star Chief; Convertible Top Cylinder; Each; Made in the USA!

Reproduction of the original convertible top cylinder designed for use with 1955-57 Bel Air, Bonneville, Catalina, and Star Chief convertible models. All convertible top cylinders are not the same. This convertible top...


Product#: HK220

1955-61 Bel Air, Impala, Electra; Convertible Top Hydraulic Hose Set; Black Rubber; Various Models

Reproduction of the original style hydraulic hose set designed to fit a wide variety of 1955-61 Buick, Chevrolet, Cadillac, Oldsmobile, and Pontiac convertible models as listed below. Finding original style hose sets for your...


Product#: TF400226

1955-57 Chevrolet Convertible Top 302 Piece Hardware Set

Complete nut, bolt, bushing and screw set to assemble convertible top frame. Instructions are included. One set required.


Product#: TF401132

1955-57 Chevy Bel Air, 150, 210, Nomad; Convertible Drain Channel; Drivers Side

Reproduction left hand drain channel for 1955-57 convertible models. Manufactured to factory specifications for a proper fit and appearance. This piece is installed below the rear pinchwelt, behind the rear seat.


Product#: TF401148

1955-57 Chevy Bel Air; Convertible Top Cylinder Bracket; Passenger Side

Reproduction top cylinder mounting bracket for 1955-57 models. This is mounted to the floor pan, and acts as the mounting point for the lower portion of the top cylinder. Mounting hardware included.


Product#: BK001

1955-57 Chevy Bel Air; Convertible Top Hydraulic System Bleeder Set

After replacing your convertible top, pump and hoses, be sure the system operates properly by bleeding all the air out of the hydraulic system. This comes with a filler plug adaptor fitting and complete instructions. Works...


Product#: TF401134

1955-57 Chevy Bel Air, 150, 210, Nomad; Convertible Drain Channel Reinforcement; Drivers Side

Reproduction drain channel reinforcement for 1955-57 convertible models. This piece helps support the drain channels for proper drainage.


Product#: UCR001

1955-64 Bel Air/Impala; Bolt Set; For Convertible Top Upper Cylinder Rod; 8-Piece Set

This is reproduction of the factory convertible top upper cylinder rod bolt set for 1955-57 Bel Air and 1958-64 Impala convertible models. Each 8-piece set includes (2) bolts, (2) nylon bushings, (2) wavy washers, and (2)...


Product#: TF401133

1955-57 Chevy Bel Air, 150, 210, Nomad; Convertible Drain Channel; Passenger Side

Reproduction right hand drain channel for 1955-57 convertible models. Manufactured to factory specifications for a proper fit and appearance. This piece is installed below the rear pinchwelt, behind the rear seat.


Product#: TF401147

1955-57 Chevy Bel Air; Convertible Top Cylinder Bracket; Drivers Side

Reproduction top cylinder mounting bracket for 1955-57 models. This is mounted to the floor pan, and acts as the mounting point for the lower portion of the top cylinder. Mounting hardware included.


Product#: TF401135

1955-57 Chevy Bel Air, 150, 210, Nomad; Convertible Drain Channel Reinforcement; Passenger Side

Reproduction drain channel reinforcement for 1955-57 convertible models. This piece helps support the drain channels for proper drainage.


Product#: TF400225

1955-57 Chevrolet Convertible Top Plates

Reproduction convertible top plates for 1955-57 models. Feature correct chrome plating and contours. Mounting screws are included.


Product#: CRP001

1955-57 Convertible Top 18 Piece Pinch Rail Pad Set

Replace your old, compressed and hardened originals, these pads will make your top replacement more complete and better fitting. Mounts in trunk between the rear pinch rail and the body.


Product#: 7614749

1949-75 GM, Dodge, Plymouth; Convertible Top Rear Window Binding End Clip, with Screw

OER reproduction of the original convertible top rear binding end clip that was used for most 1949-75 GM, Dodge, and Plymouth convertible models. This stainless steel end clip covers covers and finishes both ends of the rear...


Product#: 3698109

1951-75 Convertible Power Top Motor Mounting Grommet - Each

Reproduction of the original rubber mounting / insulation grommet used on various GM vehicles with the optional power top. These rubber grommets install on the pump assembly and secure it to the vehicle while creating a...