Product#: TF401018

1956 and 1958 Chevrolet Passenger Car; Rear Bumper to Body Seal

Reproduction of the original rear bumper to body seal designed for 1956 and 1958 Chevrolet full size passenger car models. Each body seal is manufactured to factory specifications from molded EPDM rubber. {fitment}

Product#: W2183

1962-64 Impala, Bel Air, Biscayne; Fender Skirt Splash Apron Seal Set; RH and LH; Pair; Made in the USA!

Correct reproduction of the original style splash pan seals designed for use with 1962-64 Chevrolet Impala, Bel Air, and Biscayne models. This correct reproduction of the original fender skirt splash apron used to seal the...

Product#: W2506

1969 Impala, Bel Air, Biscayne, Caprice; Front Bumper Fillers; Pair

Reproduction of the original style front bumper fillers designed for use with 1969 Impala, Bel Air, Biscayne, and Caprice models. Each of the two pieces measure 21" long x 7-1/8" wide x 3-1/2" wide at the narrower tip. Sold...

Product#: W2160

1962 Impala, Bel Air, Biscayne; Outer Rear Bumper to Body Seal; with Mounting Hardware

Excellent reproduction of the original outer rear bumper body seal strips designed for use with 1962 Chevrolet Impala, Bel Air, and Biscayne models. Each seal is manufactured to factory specifications replicating the original...

Product#: W2346

1967 Impala Full Size Rear Bumper To Body Seal - Each

Reproduction of the original body seal strip used to seal and fill the area where the rear bumper meets the body. Designed for use on 1967 Chevrolet Impala and Full Size models. This often damaged or missing part should be...

Product#: CP110

1971-76 Impala, Biscayne, Bel Air, Caprice; Inner Fender Splash Apron Seal Kit

Reproduction of the original style A-Arm seals for use with 1971-76 Chevrolet Impala, Bel Air, Biscayne, and Caprice models. Replace your old splash aprons with new reproductions and keep your engine compartment clean and...

Product#: B99136

1963-64 GM Full Size; Front Door and Rear Quarter Panel Watershield Set; 4 Door Sedan; 4 Piece Set

Reproduction style door panel and rear quarter side panel water shields for use with 1963-64 GM Full Size 4 door sedan models as listed. Replacing or installing these water shields will help to protect the back side of...

Product#: B99132

1959-60 GM Full Size; Door Panel & Rear Quarter Side Panel Watershield Set; 2 Door Hardtop 4 Piece Set

Reproduction style door panel and rear quarter side panel water shields for use with 1959-60 GM Full Size coupe models as listed. Replacing or installing these water shields will help to protect the back side of interior door...

Product#: W2324

1965 Impala, Bel Air, Biscayne; Fender Skirt Splash Apron Seal Set; RH and LH; Pair; Made in the USA!

Correct reproduction of the original style splash pan seals designed for use with 1965 Chevrolet Impala, Bel Air, and Biscayne models. This correct reproduction of the original fender skirt splash apron used to seal the...

Product#: TF300300

1959-63 Chevrolet, Pontiac Full Size; Wiring Grommet; through Quarter Panel or Tailgate; Each

Reproduction of the original wiring grommet for use with 1959-63 Chevrolet and Pontiac full size vehicles as listed below. Each grommet is manufactured in quality EPDM rubber to exact factory specifications. Allows wiring...

Product#: B99134

1961-62 GM Full Size; Front Door Panel & Rear Quarter Side Panel Watershield Set; 2 Door Hardtop; 4 Piece Set

Reproduction style door panel and rear quarter side panel water shields for use with 1961-62 GM Full Size hardtop models as listed. Replacing or installing these water shields will help to protect the back side of interior...

Product#: W2201

1963 Impala, Bel Air, Biscayne; Outer Rear Bumper to Body Seal; with Mounting Hardware

Excellent reproduction of the original outer rear bumper body seal strips designed for use with 1963 Chevrolet Impala, Bel Air, and Biscayne models. Each seal is manufactured to factory specifications replicating the original...

Product#: W2410

1968-69 Chevrolet Impala, Bel Air, Biscayne, Caprice; Fender Skirt Dust Shields; with Hardware; Pair

Correct reproduction of the original style frotn fender skirt dust seals designed for use with 1968-69 Chevrolet Impala, Bel Air, Biscayne, and Caprice models. This correct reproduction of the original fender skirt splash...

Product#: STAPLES

Staple For Inner Fender Splash Apron, 1/2 inch

Correct staple to install fender skirt splash aprons for various models. 1/2" wide, 1/2" deep.

Product#: K940

1955-90 GM; Door Lock Gasket; Various Models

Reproduction of the original door lock gasket designed for use on various GM models including the listings below. After repainting your doors, or whenever replacing door locks, be sure to install new lock cylinder gaskets to...

Product#: 152767

1958-71 Buick, Chevy, Pontiac, Olds; Door Weatherstrip Attaching Hole Sealing Plug, 27/64" Diameter; Each

Reproduction weatherstrip clip receiver seal for 1958-71 GM models. These small plugs are inserted into the door and provide a mounting point for the door frame weatherstrip clips to insert into. Sold individually. 26...

Product#: R889

1965-79 GM; Door Handle Gasket Set; Outer; Various Models

This reproduction gasket set includes a complete set of door handle gaskets used to install the outer door handles on the various models listed below. Each set includes correct die-cut gaskets for both RH and LH outer door...

Product#: R355

1966-72 GM; Outer Mirror Mounting Set ; LH or RH ; Gasket, Bracket, Screws

Reproduction of the original style components required to replace and mount the outer door mirror on the door. Contains all the necessary hardware to install a standard outer door mirror onto either the drivers or passenger...

Product#: 1667195

1955-1976 GM; Rubber Floor Pan Plug; Each

Reproduction of the original round rubber floor pan plug installed on various 1955-76 General Motors vehicles. Found in various locations on the floor pan, these plugs are manufactured to factory specifications in quality...

Product#: K991

1966-72 Chevrolet; Standard Door Mirror Gasket

Quality reproduction outer door mirror gasket for various GM models. Manufactured to factory specifications in quality injection molded ABS, will fit original GM or reproduction mirrors. Installs between the mirror base and...