1960 Lincoln All Models Painless Performance Products

Ideal for any type of street rod, muscle car or kit car. Universal kit includes wires and light sockets to install courtesy lights inside your vehicle. Installation Instructions: Download Here Made in USA

This Park / Neutral relay set uses the stock neutral safety switch to also provide for ECM park/neutral ground signal needed when installing factory-style fuel injection into older vehicles. For use with any aftermarket...

This Painless Performance premium performance terminal assortment kit provides 84 pieces of assorted sized electrical teminals. These terminals are American made and are top quality. The terminal assortment kit weighs one...

This Fan-Thom II kit comes with a threaded thermostat that screws into the engine block or intake manifold for a professional looking installation. This is inexpensive protection for an electric fan and a vehicle's wire...

Perfect for trunk mounted batteries. Both positive and negative cables are 1 gauge and 16 feet in length which allows for them to be attached to the engine for maximum starting current. Helps prevent voltage drop to the...

Are you looking to remote mount your fuse block and you want full power options? Then this 28-circuit kit will provide you with all those power accessory circuits, as well as extra long wires allowing you to mount the fuse...

Installing a Painless fuel injection harness and want to keep all your emissions devices intact? The Painless solution is to install a Painless emissions harness. These harnesses activate the AIR Port Solenoid Control, AIR...

This harness is standalone and is not intended to replace the OEM engine wiring. Standalone harnesses are intended to run the designated engine & transmission only, generally when swapped into another vehicle. This harness...

Mounts in 1/8" hole. 12 Volt operation. Made in USA

Designed specifically to prevent voltage drops at the fuel pump to maintain constant fuel pump pressure and to prevent fuel pump amperage overloads from damaging the vehicle's electrical system. Set includes: 30 amp heavy...

When you need protection from the harsh conditions, this set provides complete protection from the elements to ensure reliable and dependable performance. This is inexpensive protection for an electric fan and a vehicle's...

When upgrading tail lights to the newer high wattage halogens, always use a relay. This kit gives you everything you need to protect your wiring and switches. Made in USA Installation Instructions: Download Here

This 21-circuit kit is our most widely used customizable chassis harness. You'll find that it's easily adaptable to almost any vehicle. This universal harness will work on carbureted or any stand alone fuel injected engine...

Mounts in 1/2" hole. 12 Volt operation. Made in USA

This harness is standalone and is not intended to replace the OEM engine wiring. Standalone harnesses are intended to run the designated engine & transmission only, generally when swapped into another vehicle. If you...

A common problem faced by rodders and kit car builders is where to mount turn signals since many aftermarket steering columns are not designed to accommodate the necessary wiring and switches. Problem solved, with this new...

This kit has only the highest quality components. Kit comes complete with 16 feet of red #1 gauge positive cable and 3 feet of black #1 gauge cable, both with heavy duty battery terminals already installed capable of...

If you want to keep your under-dash area organized or you think that you need to remove gauges from time to time then you need to install our universal gauge harness. Installation Instructions: Download Here Made in USA ...

This Painless Performance 28 circuit chassis harness is our most widely used customizable automotive wiring harness. This universal kit is great for hot rod or street rod builds, but you'll find that it's easily adaptable to...

This 250 AMP dual battery controller set includes a three position switch to control the second battery through the operation of the solenoid. Switch position one isolates the auxiliary battery. No light. Position two...

This is our customizable 21 circuit pickup chassis harness. You'll find that the ample wire lengths make this kit especially suited for trucks with long beds and extended cabs. We offer two versions, one with the GM column...

This 28-circuit kit includes most all the power accessory circuits you have been looking to add to your vehicle. This universal harness will work on carbureted or any stand alone fuel injected engine with any type...

The safe way to add electrical accessories to any vehicle is with a Painless Performance CirKit Boss. The CirKit Boss is the first circuit isolator system available with both constant and ignition hot circuit kits. The kit...

This harness is standalone and is not intended to replace the OEM engine wiring. Standalone harnesses are intended to run the designated engine & transmission only, generally when swapped into another vehicle. If you require...

Mounts in 5/16" hole. 12 Volt operation. Made in USA

The safe way to add electrical accessories is with a CirKit Boss®™ kit from Painless Performance. This kit allows for the addition of 3 fused circuits to your already existing factory fuseblock. Simply mount the fuse block...

H4 Headlight plugs. Preterminated with butt connectors for easy attachment. Perfect for replacement of worn original connectors.

Installing a Painless fuel injection harness and want to keep all your emissions devices intact? The Painless solution is to install a Painless emissions harness. These harnesses activate the AIR Port Solenoid Control, AIR...

This Fan-Thom II kit comes with a threaded thermostatic switch that screws into the extra coolant temperature sensor port of the passenger engine head on Generation III and up GM engines for a professional looking...

This 21 circuit universal harness is adaptable to fit the 1960's, 70s, or 80s GM, and Chrysler muscle cars where a bulkhead connector is required. Some minor bulkhead modification may be required. Included with this harness...

Installing air conditioning to your hot rod with dual electric cooling fans? Need cooling fan relays to operate off a thermostatic switch and when your AC is on? Then this dual activation cooling fan relay set by Painless...

Mounts in 5/16" hole. 12 Volt operation. Made in USA

If you want to keep your under-dash area organized or you think that you need to remove gauges from time to time then you need to install our universal gauge harness. Installation Instructions: Download Here Made in USA ...

Replacement pigtail for GM HEI distributors. Made in USA

The safe way to add electrical accessories to any vehicle is with a Painless Performance CirKit Boss. This is the first circuit isolator system available with both constant and ignition hot circuits. The kit includes an...

This weatherproof Fan-Thom II kit comes with a threaded thermostat that screws into the engine block or intake manifold for a professional looking installation. This is inexpensive protection for an electric fan and a...

This relay harnesses set provides maximum battery voltage to maximize cooling efficiency and to protect the main electrical system from damaging amperage overloads. This weatherproof water pump relay harness is perfect for...

Perfect for replacing damaged, missing or worn out original connectors for GM steering columns. Pigtails include proper crimps installed on factory connectors for an OE appearance and GM color coded, industry certified...

The solution for vehicles with GM starters that are hard to start when hot, or vehicles with old or worn out electrical systems. Works by boosting available amperage to the starter solenoid. Installation Instructions:...

This harness is standalone and is not intended to replace the OEM engine wiring. Standalone harnesses are intended to run the designated engine & transmission only, generally when swapped into another vehicle. If you...

This Remote Master Disconnect with Mechanical Latching Solenoid is ideal for everyday vehicle applications and is a simple and effective theft deterrent. Features a constant hot wire for computer or radio presets. It uses a...

This set allows you to position the starter solenoid any place you need to in order to make maintenance easier, clean up an inner fender or just replace a factory starting circuit. Installation Instructions: Download Here ...

This kit uses a 250 AMP solenoid and toggle switch. This switch can be hidden anywhere in the vehicle as a anti-theft deterrent by disconnecting the constant battery power from the battery to the fuse block. Kit comes...

Mounts in 1/8" hole. 12 Volt operation. Made in USA

The solution for vehicles with GM starters that are hard to start when hot, or vehicles with old or worn out electrical systems. Works by boosting available amperage to the starter solenoid. The Hot-Shot Plus model includes...

This Painless Performance modular blank fuse block can be used on any vehicle where additional circuits are needed. The four circuit ATO fuse center works great for in-line wiring applications, such as trailer wiring or when...

Use this 20 Circuit OEM style pre-wired fuse block to replace your existing fuse block or as a starting point for custom wiring. All you have to do is terminate your circuit wire and attach it to the fuse block. ...

Weld-in oxygen sensor fitting for all fuel injection systems. Fits TBI, TPI, CMFI, LT1, LSX, 5.0L and most other oxygen sensors. Important: This part requires welding for installation. Professional installation is...

The safe way to add electrical accessories to any vehicle is with a Painless Performance CirKit Boss. The CirKit Boss is the first circuit isolator system available with both constant and ignition hot circuits. This CirKit...

Relay banks are ideal for powering accessories such as fuel pumps, water pumps, throttle stops, electric cooling fans, nitrous solenoids, etc. and for keeping the relays in a centralized location. Installation Instructions:...

Relay banks are ideal for powering accessories such as fuel pumps, water pumps, throttle stops, electric cooling fans, nitrous solenoids, etc. and for keeping the relays in a centralized location. Installation Instructions:...

Vehicle Anti-Theft (VATS) defeat module. This module is included with the 60502 & 60505 harness kits. This module is meant to work when swapping an 92-93 LT1, 94-95 LT1, or 97-98 LS1 engine into a different application and...

Mounts in 1/2" hole. 12 Volt operation. Made in USA

Voltage spikes can cause damage to various components in your vehicle's electrical system. This easy to install device clips the spikes at 14.5 volts to protect sensitive electrical accessories. Installs between positive and...

This harness is standalone and is not intended to replace the OEM engine wiring. Standalone harnesses are intended to run the designated engine & transmission only, generally when swapped into another vehicle. This Painless...

The junction block with two ten gauge posts is the perfect way to attach large gauge wire connections.

This set is designed to allow a wide range of temperature adjustments for your electric fan. A bulb at the top of the capillary tube is designed to probe or be attached to the top or hottest portion of the radiator. The...

This is a replacement switch for use with the Painless Fan-Thom II electric fan relay set. Made in USA Includes: 195° F on / 185° F off thermostat 1/2" NPT to 3/8" NPT adapter Insulated terminals

The safe way to add electrical accessories to any vehicle is with a Painless Performance CirKit Boss. The CirKit Boss is the first circuit isolator system available with both constant and ignition hot circuits. This kit...

Installing air conditioning to your hot rod with dual electric cooling fans? Need cooling fan relays to operate off a thermostatic switch and when your AC is on? Then this dual activation cooling fan relay set by Painless...