Product#: MN45058

1970-71 Mopar 340 Six Pack Installation Kit ; Small Block

This reproduction six pack installation kit comes with everything you need to hook up a small block six-barrel induction system. Kit includes throttle cable, fuel lines, coil bracket, linkage kit, choke, nuts, springs and...


Product#: UK915

Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 36" Long

This universal anti-squeak insulator set includes two rubber strips that insert in between the gas tank and the mounting straps to eliminate any noise from tank movement and vibration which may occur. One foam rubber pad...


Product#: AL124

Accelerator Throttle Rod; Universal Fit

Universal style accelerator throttle rod for various GM, Ford, Chrysler, Dodge, Plymouth models. This accelerator rod is for use when modifications will not allow the use of the original rod between the accelerator pedal...


Product#: MM8271

1960-1976 Chrysler, Dodge, Plymouth; Fuel Tank Mounting Studs ; Pair; OER

Reproduction of the original style fuel tank mounting studs designed for use on various 1960-1976 Mopar models. Fuel tank mounting studs, also known as J-bolts, are required when replacing your fuel tank straps. Manufactured...


Product#: C67808

1959-1988 GM; Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 39" Long; For 1" Wide Straps

Universal style anti squeak cushions are designed to install between the gas tank and the gas tank straps. These fuel tank anti squeek pads cushion the gas tank from the body and straps to reduce noise caused by metal to...


Product#: CX5042

1954-59 Chevy, GMC Truck; Fuel Tank Sending Unit; Universal Fit; without Pick-Up Tube; 0-90 Ohm

Universal fuel tank sending unit for various GM and other models that require a 90 ohm sender. Designed for use with OE or aftermarket 0-90 ohm gauges, each sending unit includes the sender, float, float rod, hardware,...


Product#: 9047E

Fuel Filler Hose; Nitrile 70 Shore Rubber; 2" ID x 15" Length

Reproduction fuel filler hose to connect fuel neck to fuel tank on a variety of models requiring a 2" ID fuel hose. This hose can be used as is, or if you require a shorter piece, you can cut this 15" fuel hose to your...


Fuel Filler Hose; Nitrile 70 Shore Rubber; 2" ID x 20" Length
NEW

Product#: 9047G

Fuel Filler Hose; Nitrile 70 Shore Rubber; 2" ID x 20" Length

Reproduction fuel filler hose to connect fuel neck to fuel tank on a variety of models requiring a 2" ID fuel hose. This hose can be used as is, or if you require a shorter piece, you can cut this 20" fuel hose to your...


Product#: 3577527

1971-72 Mopar Accelerator Pedal Pad ; A,B,C,E-Body

Reproduction of the original accelerator pedal pad designed for use on various Chrysler, Dodge and Plymouth A, B, C, and E-body models. This injection molded ABS pedal pad is an accurate reproduction of the original pad...


Product#: MD2608

1971-72 Mopar Accelerator Pedal Hardware ; A, B, C, E Body ; Various Models

Reproduction of the original accelerator pedal hardware designed for use on 1971-72 A/B/C/E-Body Mopar models. Components are designed to attach the accelerator pedal to the vehicle. This hardware set includes the pedal...


Product#: TF700512

Spring Steel Rod Clip, Fits 1/4" Rod Diameter, RH, 17/64" ID.

Correct style rod clip used on various GM vehicles. Fits 1/4" rod diameter, RH, 17/64" ID. These reproduction transmission linkage rod clips need to be replaced when replacing your linkage rods. 1955-57 Chevrolet...


Product#: 14048

1958-88 Holley Carburetor Fuel Bowl Screw; 2-1/2"

Reproduction 2-1/2" flat blade carburetor fuel bowl screw for Holley carburetors. This special screw is specifically designed in the correct original configuration and head design for the early model Holley carburetors. Many...


Product#: K915

Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 24" Long; For 1" Wide Straps

Reproduction fuel tank anti squeek set for vehicle models. Includes one 5-1/4" x 2" x 1/2" precision die cut neoprene tank to floor cushion, two 24" x 1-1/4" molded rubber strap to tank cushions, and two 24" x 2 " x .060"...


Product#: T76063

Billet Aluminum; Fuel Filler Neck; with Pop-Up Gas Cap

Billet aluminum flush mount fuel filler neck with pop-up gas cap is the perfect addition to your classic car or truck when adding a non-stock fuel filler location or relocating your fuel tank. Features a super sanitary and...


Product#: 62531

Electric Fuel Pump; with Cadmium Plated Housing; 100 GPH - 7 PSI

This externally-mounted electric fuel pump is ideal for most street and strip applications. Proven rotary vein technology provides high flow and stable pressures with minimal vibration and sound. Each pump features 3/8"...


Product#: 62561

Electric Fuel Pump; with Cadmium Plated Housing; 140 GPH - 9 PSI

This externally-mounted electric fuel pump is ideal for most street and strip applications. Proven rotary vein technology provides high flow and stable pressures with minimal vibration and sound. Each pump features 3/8"...


Product#: CX5041

1954-59 Chevy, GMC Truck; Fuel Tank Sending Unit; Universal Fit; w/o Pick-Up Tube; 0-30 Ohm

Universal fuel tank sending unit for various GM and other models that require a 30 ohm sender. Designed for use with OE or aftermarket 0-30 ohm gauges, each sending unit includes the sender, float, float rod, hardware,...


Product#: 479312

1947-76 GM, Chrysler, Dodge, Plymouth; Brass Fuel Tank Sending Unit Float

Reproduction brass fuel sending unit float for various 1947-76 General Motors, and Chrysler, Dodge, Plymouth models. If your fuel gauge isn't reading correctly, it may be the fuel sending unit float. The original OE float may...


Product#: MD2144

1971-72 Dodge, Plymouth; Accelerator Pedal Pad and Bezel Kit ; Various Models

Reproduction of the original accelerator pad, bezel and hardware designed for use on Dodge and Plymouth A, B and E-body models. This injection molded ABS accelerator pedal pad set includes the pedal pad, stainless steel...


Product#: 14305

Holley Carburetor Float Bowl Screws; Set of 8

Reproduction set of 2-1/2" flat blade carburetor fuel bowl screws for Holley carburetors. These special screws are specifically designed in the correct original configuration with the proper head design for the early model...