1963 Dodge Polara Parts - Rear End

Reproduction rear and housing e-brake, and brake line clip set for all 1960-76 models. Replace your rusted originals with these correct replacements. Must be welded to the factory locations.

This is a high strength axle shaft for Mopar muscle cars equipped with an 8-3/4" rear end. Yukon axles are made from 1541H alloy and are deeply heat-treated to be 20-25% stronger than OEM 1040/1050 steel axles. The axle features rolled spline s, which offer a 30% strength increase over cut spline axles. Sold as a set. Features: Fits Mopar 8.75" differentials 30 spline Cut to length design fits 28"-32" applications 5 x 4.5" bolt pa ttern Includes: Two 32" cut to length axles Two green bearings Ten axle studs Note: These axles are "cut to length" designed axles. compatible Dif ferentials Chrysler 8.75", 41 Case Housing Chrysler 8.75", 42 Case Housing Chrysler 8.75", 89 Case Housing Applications: 1963 - 1973 Chrysler New Yorker 1970 - 1973 Dodge Challenger 1968 - 1973 Dodge Charger 1965 - 1973 Dodge Coronet 1966 - 1973 Dodge Dart 1965 - 1973 Dodge Monaco 1963 - 1973 Dodge Polara 1964 - 1969 Plymouth Barracuda 1970 - 1973 Plymouth Cuda 1967 - 1970 Plymouth Belvedere 1970 - 1972 Plymouth Duster 1965 - 1973 Plymouth Fury 1967 - 1970 Plymouth GTX 1968 - 1972 Plymouth RoadRunner 1968 - 1973 Plymouth Satellite

This is a high strength axle shaft for Mopar muscle cars equipped with an 8-3/4" rear end. Yukon axles are made from 1541H alloy and are deeply heat-treated to be 20-25% stronger than OEM 1040/1050 steel axles. The axle features rolled spline s, which offer a 30% strength increase over cut spline axles. Features: Fits Mopar 8.75" differentials 30 spline Cut to length design fits 28"-32" applications 5 x 4.5" bolt pattern Important: Must use with Green bearings (sold separately). Note: This axle is a "cut to length" designed axle. compatible Differentials Chrysler 8.75", 41 Case Housing Chrysler 8.75", 42 Case Housing Chrysler 8.75", 89 Case Housing Applications: 1963 - 1973 Chrysler New Yorker 1970 - 1973 Dodge Challenger 1968 - 1973 Dodge Charger 1965 - 1973 Dodge Coronet 1966 - 1973 Dodge Dart 1965 - 1973 Dodge Monaco 1963 - 1973 Dodge Polara 1964 - 1969 Plymouth Barracuda 1970 - 1973 Plymouth Cuda 1967 - 1970 Plymouth Belvedere 1970 - 1972 Plymouth Duster 1965 - 1973 Plymouth Fury 1967 - 1970 Plymouth GTX 1968 - 1972 Plymouth Road Runner 1968 - 1973 Plymouth Satellite

Did you know the rear axle housing was shipped to the assembly plant without the brake lines and fittings in place? A special piece of tape covered the vent hole to keep debris & moisture out during shipping. The plant then...

Did you know the rear axle housing was shipped to the assembly plant without the brake lines and fittings in place? A special piece of tape covered the vent hole to keep debris & moisture out during shipping. The plant then...

Reproduction of the original style factory rear axle bearing retainer gasket designed for use on most 1960-76 A, B and E-Body Dodge and Plymouth models.This retainer gasket will replace the worn out or missing original....

Mopar 8-3/4" "89" case housing

Original quality replacement rear differential cover gasket. New gaskets should always be used whenever removing or replacing rear end covers. Applications: A-Body 1961-62 Lancer 1961-74 Valiant 1963-74 Dart 1964-69...

This cast iron reproduction yoke is manufactured specifically for Dana 60 rear axles. Includes the yoke, retaining u-bolt, and mounting hardware. Note: Uses 1330 series U-joints (sold separately) that have a 3.625 " snap...

This cast iron reproduction yoke is manufactured specifically for Dana 60 rear axles. Includes the yoke, retaining strap and mounting hardware. Note: Uses 1350 series U-joint (sold separately) that have a 3.625" s nap ring...

This billet steel reproduction yoke is manufactured specifically for Dana 60 rear axles. Includes the yoke, retaining strap and mounting hardware. Note: Uses 1350 series U-joint (sold separately) that have a 3 .625" snap...

This cast iron reproduction yoke is manufactured specifically for Dana 60 rear axles. Includes the yoke, retaining strap and mounting hardware. Note: Uses 1350 series U-joint (sold separately) that have a 3.625" s nap ring...

This cast iron reproduction yoke is manufactured specifically for Dana 60 rear axles. Includes the yoke, strap, and mounting hardware. Note: Uses 7290 series U-joints (sold separately) that have a 2.625" snap ring span with...

This forged steel reproduction yoke is manufactured specifically for Dana 60 rear axles. Includes the yoke, retaining u-bolt and mounting hardware. Note: Uses 1350 series U-joint (sold separately) that have a 3.62 5" snap...

This cast iron reproduction yoke is manufactured specifically for Dana 60 rear axles. Includes the yoke, u-bolt, and mounting hardware. Note: Uses 1310 series U-joints (sold separately) that have a 3.219" snap rin g span...

This cast iron reproduction yoke is manufactured specifically for Dana 60 rear axles. Includes the yoke, strap, and mounting hardware. Note: Uses 1310 series U-joints (sold separately) that have a 3.219" snap ring span with...

The Moser Dana 60 Muscle Pak gives you a complete axle assembly ready to install in your Mopar. Assembly work has been completed by Moser's expert technicians, all you have to do is add gear oil! You get a brand new Moser...

The Moser Muscle Pak gives you a complete axle assembly ready to install in your Mopar. Assembly work has been completed by Moser's expert technicians, all you have to do is add gear oil! You get a brand new Moser stamped...

The Moser Muscle Pak gives you a complete axle assembly ready to install in your Mopar. Assembly work has been completed by Moser's expert technicians, all you have to do is add gear oil! You get a brand new Moser stamped...

The Moser Dana 60 Muscle Pak gives you a complete axle assembly ready to install in your Mopar. Assembly work has been completed by Moser's expert technicians, all you have to do is add gear oil! You get a brand new Moser...

The Moser Muscle Pak gives you a complete axle assembly ready to install in your Mopar. Assembly work has been completed by Moser's expert technicians, all you have to do is add gear oil! You get a brand new Moser stamped...

The Moser Muscle Pak gives you a complete axle assembly ready to install in your Mopar. Assembly work has been completed by Moser's expert technicians, all you have to do is add gear oil! You get a brand new Moser stamped...

The Moser Dana 60 Muscle Pak gives you a complete axle assembly ready to install in your Mopar. Assembly work has been completed by Moser's expert technicians, all you have to do is add gear oil! You get a brand new Moser...

The Moser Dana 60 Muscle Pak gives you a complete axle assembly ready to install in your Mopar. Assembly work has been completed by Moser's expert technicians, all you have to do is add gear oil! You get a brand new Moser...

This forged steel yoke is manufactured specifically for Mopar differentials. Includes the yoke, and mounting hardware. Important: Use MM3310 strap kit, Note: Uses 1350 series U-joint (sold separately) that have a 3.625"...

This billet steel yoke is manufactured specifically for Mopar differentials. Includes the yoke, and mounting hardware. Important: Use MM3307 u-bolt kit, Note: Uses 1350 series U-joint (sold separately) that have a 3.625"...

This chrome moly billet yoke is manufactured specifically for Mopar differentials. Includes the yoke, u-bolt, and mounting hardware. Note: Uses 7260 series U-joint (sold separately) that have a 2.125" snap ring sp an with a...

Replacement 29 spline yoke for Chrysler 8-3/4" rear end applications with 1-7/8" pinion stem. Designed to be a high strength factory-style replacement for the original. Note: Uses 7260 series U-joint (sold separat ely) that...

This billet steel yoke is manufactured specifically for Mopar differentials. Includes the yoke, and mounting hardware. Important: Use MM3307 u-bolt kit, Note: Uses 1350 series U-joint (sold separately) that have a 3.625"...

This cast iron yoke is manufactured specifically for Mopar differentials. Includes the yoke, and mounting hardware. Important: Use MM3311 s trap kit, Note: Uses 7260 series U-joint (sold separately) that have a 2.125" snap...

This chrome moly billet reproduction yoke is manufactured specifically for Mopar differentials. Includes the yoke, u-bolt, and mounting hardware. Note: Uses 7290 series U-joints (sold separately) that have a 2.62 5" snap...

Replacement 29 spline yoke for Chrysler 8-3/4" rear end applications with 1-7/8" pinion stem. Designed to be a high strength factory-style replacement for the original. Note: Uses 7290 series U-joints (sold separa tely) that...

Mopar 8-3/4" or 9-1/4" with "41" or "89" case housing

Replacement style universal joint service package for use with various 1960-66 Chrysler, Dodge, and Plymouth A, B, C models as listed. Universal Joint Service Package; front "Detroit" style ball & trunion repair kit. Note:...

Motive Gear offers some of the toughest drivetrain components on the market today. Their products can be found in the winner's circle at NHRA, IHRA, ANDRA, SODA, SCORE, and NASCAR events. The superior quality components is...

Motive Gear offers some of the toughest drivetrain components on the market today. Their products can be found in the winner's circle at NHRA, IHRA and NASCAR events. The superior quality components is the result of years of...

Richmond Gear offers some of the toughest drivetrain components on the market today. Their products can be found in the winner's circle at NHRA, IHRA and NASCAR events. The superior quality components is the result of years...

Motive Gear offers some of the toughest drivetrain components on the market today. Their products can be found in the winner's circle at NHRA, IHRA and NASCAR events. The superior quality components is the result of years of...

Motive Gear offers some of the toughest drivetrain components on the market today. Their products can be found in the winner's circle at NHRA, IHRA and NASCAR events. The superior quality components is the result of years of...

Yukon master overhaul kit for Chrysler 8.75" rear ends. Included in this kit are Timken carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, oil baffles and...

Work on your differential third member safely and easily with this lightweight fixture. It can be clamped or bolted to your work bench or simply mounted in a vise, and it fits neatly in your tool chest when the job is...

Replacement crush sleeve for setting up your rear axle. Crush sleeves cannot be reused if you are changing a ring and pinion or the front seal. Includes pinion nut washer and pinion flange nut. These are for the 9-1/4"...

Chrome differential cover bolts for 8-1/4" rear axles. Each set includes enough bolts to mount the differential cover to the axle housing.s

Replacement thrust spacer set for 8-3/4" differentials with clutch type Sure-Grip prior to 1970. Required to provide axle thrust surface in four-spider differential applications. One set required per vehicle.

Max-Gear is an ultra-tough automotive gear oil. It’s designed to maximize power and provide unsurpassed protection to heavily loaded gears. It makes gears run smoother, quieter, cooler and longer without overhauls. Max-Gear...

This is a quality replacement U-joint for your Mopar. Features: Cap dia. 1-3/16" and 1-1/16" Forged and case hardened alloy steel crosses Heat-treated needle bearings Cold-formed radial bearing cups for 360° lubrication...

These u-joint u-bolt kits are designed for use on stock and Yukon pinion yokes with 1350 u-joint size. Includes: two u-bolts and four nuts. Made in the USA.

These u-joint strap kits are designed for use on stock and Yukon pinion yokes with 1310 u-joint size. Includes: two straps and four bolts. Made in the USA.

This strap set includes two 1-1/2" bolt center clamps, four 1/4-28 x 5/8" cap screws, 4 washers and is for MM3087 u-joint only.

This locking pawl and flanged nut is used on the right side axle of 8-3/4" differentials. The pawl secures the axle end play adjusting nut once proper bearing play is established.

These u-joint strap kits are designed for use on stock and Yukon pinion yokes with 7260 u-joint size. Includes: two straps and four bolts. Made in the USA.

FilterMag’s powerful rare-earth magnet trap and hold wear inducing metal particles smaller than 40-microns down to 1-micron. The super-strong magnetic force holds FilterMag to the cover, is reusable and will reduce...

Max-Gear is an ultra-tough automotive gear oil. It’s designed to maximize power and provide unsurpassed protection to heavily loaded gears. It makes gears run smoother, quieter, cooler and longer without overhauls. Max-Gear...

Ring gear bolts for Mopar 8-1/4" and 8-3/4" differentials. These are genuinely direct from Mopar Performance. Sold as a set of 12.

Yukon master overhaul kit for Chrysler 8.75" rear ends. Included in this kit are Timken carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, oil...

Auburn Gear’s Pro Series limited-slip differential outperforms standard OEM differentials hands down. It delivers more traction and faster engagement for controlled power transfer and lightning fast reaction to changing load...

Used by Joe Gibbs Racing in every rear end differential and transmission gear box. This fully synthetic, unique SAE 75W-110 gear oil reduces operating temperatures by up to 15 degrees compared to other brand gear oils.

Used by Joe Gibbs Racing in every rear end differential and transmission gear box. This fully synthetic, unique SAE 75W-110 gear oil reduces operating temperatures by up to 15 degrees compared to other brand gear oils.

Ring gear bolts for Mopar 8-1/4" and 8-3/4" differentials. These are factory replacement quality. Sold as a set of 12.