1965-69 Impala, Camaro, Bel Air, Firebird; Hood Insulation Fastener; Black Nylon
Replacement black nylon 2" square head hood insulation retainer is just what your classic vehicle needs to keep your original hood insulation where it belongs...attached to the hood. This retainer is a service replacement for...
1965-69 Impala, Camaro, Bel Air, Firebird; Hood Insulation Fastener; Black Nylon
Classic $0.99 ea
1970-74; Challenger, Barracuda, Cuda; Hood Hinges; with Springs; Pair
Reproduction of the original 1964-1974 Plymouth Barracuda hood hinges designed for 1970-74 Mopar E-body models. Each hood hinge is manufactured to exact factory specifications and includes OE style hood hinge springs. Get...
1970-74; Challenger, Barracuda, Cuda; Hood Hinges; with Springs; Pair
Classic $324.99 pr
1970 Plymouth Barracuda, Cuda; Hood Latch Assembly; EDP Coated
Reproduction of the original hood latch assembly panel designed for use with 1970 Barracuda and Cuda models. Each hood latch assembly is manufactured in stamped steel to original factory specifications featuring correct...
Hex Head SEMS Body Bolt Set; 3/8"-16 x 1"; For Hood Hinges; 8 Piece Set
OER Authorized, direct replacement hood hinge to fender bolt set for various GM vehicles. This kit consists of a quantity of 8 black phosphate coated (9/16" head size) hex washer head SEMS body bolts with 3/8"- 16 x 1" specs....
Hex Head SEMS Body Bolt Set; 3/8"-16 x 1"; For Hood Hinges; 8 Piece Set
Classic $7.99 set
Hex Head SEMS Body Bolt Set; 3/8"-16 x 1"; For Hood Hinges; 10-Pieces
Black phosphate coated hex head bolts with washer. Measures 3/8-16 x 1" SEMS with 1" outside diameter to fit a variety of applications, including the hood latch on 1970-81 Firebird, and 1973-80 Chevrolet or GMC truck, among...
Hex Head SEMS Body Bolt Set; 3/8"-16 x 1"; For Hood Hinges; 10-Pieces
Classic $9.99 set
Hood Insulation Fastener; 5/16" Stem Diameter; 3/4" Stem Length; 1-3/4" Head Diameter; 20-Pieces
Replacement black nylon 1-3/4" hood insulation retainer is just what your GM vehicle needs to keep your original hood insulation where it belongs... attached to the hood. This retainer is a service replacement for most...
Hood Insulation Fastener; 5/16" Stem Diameter; 3/4" Stem Length; 1-3/4" Head Diameter; 20-Pieces
Classic $17.99 set
1970-2002 GM; Hood Insulation Fastener; Each
Replacement black nylon hood insulation fastener is just what your GM vehicle needs to keep your original hood insulation where it belongs... attached to the hood. This retainer is a service replacement for most models. It...
1970-74 Plymouth Barracuda; Twin Bulge Hood Scoop Ornament Set
Reproduction of the original twin bulge hood scoop ornaments designed for use on 1970-74 Plymouth Barracuda models. Each hood ornament is manufactured to factory specifications for proper fitment and appearance. Includes 2...
1970-74 Dodge/Plymouth E-Body/1971-72 Plymouth B-Body 2-Door; Hood Latch Support; EDP Coated
Reproduction of the original hood latch support for 1971-72 Plymouth B-Body (2-door), and 1970-74 Dodge & Plymouth E-Body models. Each hood latch support is manufactured in stamped steel to original factory specifications...
1970-74 Dodge/Plymouth E-Body/1971-72 Plymouth B-Body 2-Door; Hood Latch Support; EDP Coated
Classic $44.99 ea
Reproduction hood pin rubber gasket found on models with hood pins. Each gasket is die-cut to proper dimension. Will also fit a wide variety of aftermarket hood pins. Sold individually. Use as required. Check measurements...
DEI Boom Mat Under Hood Black Thermal Acoustic Lining
DEI Black Under Hood thermal acoustic lining. Designed specifically for under hood applications, this lining will greatly reduce the heat, noise, and vibration coming from your engine compartment. This black self adhesive...
1964-72 Dodge/Plymouth A, B, E-Body, Hood Insulation Clip
Factory style replacement black plastic hood insulation clip. Measurement: Shaft Size - 11/16" long x 1/4" wide. Sold individually. Applications: 1964-72 Mopar A-Body models 1964-72 Mopar B-Body models 1970-72 Mopar E-Body...
Track Spec Hood Louver Set - Designed for 2005-13 Corvette
Track Spec light weight aluminum three piece hood louver kit for 2005-13 Corvette. Each vent is designed for structural rigidity and contoured to fit the specific vehicle. Powder coated satin black for a durable and clean...
Lokar Hood/Trunk Release Cable Set Black
Billet aluminum handle assembly for both the hood and trunk. The cables are "U-Cut-to-Fit", designed with specially extruded liner for extended life of the cable, with aluminum fittings and stainless steel inner wire. Hood...
Track Spec GT4 Center Vent 18.5 x 16.25
Track Spec light weight aluminum universal hood louver center vent. Each vent is designed for structural rigidity and powder coated satin black for a durable and clean finish. Includes detailed instructions and all hardware...
Track Spec Long-Style Hood Louver - Designed for 1968-82 Corvette
Track Spec light weight aluminum hood louvers for 1968-82 Corvette. Each vent is designed for structural rigidity and contoured to fit the specific vehicle. Powder coated satin black for a durable and clean finish. Includes...
Track Spec Long-Style Hood Louver - Designed for 1968-82 Corvette
Classic $229.99 ea
Track Spec T2 SCCA 200 Sq Inch Angled Center Vent
Track Spec light weight aluminum universal hood louver center vent. Each vent is designed for structural rigidity and powder coated satin black for a durable and clean finish. Includes detailed instructions and all hardware...
Track Spec; Universal Hood Louver Center Vent; GT2 14.75" x 26"
Track Spec light weight aluminum universal hood louver center vent. Each vent is designed for structural rigidity and powder coated satin black for a durable and clean finish. Includes detailed instructions and all hardware...
Track Spec; Universal Hood Louver Center Vent; T1 13.5" x 19.75
Track Spec light weight aluminum universal hood louver center vent. Each vent is designed for structural rigidity and powder coated satin black for a durable and clean finish. Includes detailed instructions and all hardware...
Track Spec Hood Louver- Designed for 2010-15 Camaro
Track Spec light weight aluminum hood louvers for 2010-15 Camaro. Each vent is designed for structural rigidity and contoured to fit the specific vehicle. Powder coated satin black for a durable and clean finish. Includes...