1966 Chevrolet C10 Panel Parts - Suspension

Sway bars are the key to having a great handling vehicle. They reduce body roll and help control over steer and under steer in corners. INCLUDES 1-1/4" Sway Bar Poly Bushings Mounting Brackets All necessary hardware Black...

Reproduction of the original style rear axle trac-bar bushing designed for use with 1960-72 Chevrolet and GMC truck models. Each bushing is manufactured to factory specifications. Designed for the trac-bar that connects from...

Technically correct in appearance with original factory installed component. OE quality reproduction from Classic Suspensions. Manufactured by an OE supplier to modern technical specifications while offering restorers an...

Front shock relocation kit for 1963-72 Chevy C10 trucks with lowered suspension. These brackets move the upper shock mount upward 2-1/2” recovering shock travel and correcting the suspension geometry on lowered trucks. Kit...

1963-72 Chevrolet/GMC truck blocks lower the rear of your coil spring truck up to 2" without affecting your ride quality. These block kits allow the vehicle's shock angle to remain unchanged from the factory position. Works...

1963-72 Chevrolet/GMC truck Blocks lower the rear of your coil spring truck up to 2" without affecting your ride quality. These block kits allow the vehicle's shock angle to remain unchanged from the factory position. Works...

1963-72 Chevrolet/GMC truck Blocks lower the rear of your coil spring truck up to 2" without affecting your ride quality. These block kits allow the vehicle's shock angle to remain unchanged from the factory position. Works...

These sway bars are designed to minimize body roll, under-steer and over-steer when cornering, resulting in improved vehicle handling and control. These offer all of the above without affecting your ride quality. Kit...

New stock style lower control arms designed for use with 1963-70 Chevrolet and GMC C10 pickup, panel, and Suburban models. Includes both RH and LH lower control arms with cross shafts, bushings, and ball joints pre-installed....

Reproduction of the original upper control arm designed for use with 1963-70 Chevrolet and GMC Pickup, Suburban, Panel Truck, Crew Cab, Blazer and Jimmy 1/2 ton, 2 wheel drive models. Also fits 1970 Chevrolet G10/G20 Van, and...

Reproduction of the original style lower ball joint for use with 1963-70 Chevrolet and GMC trucks. If your suspension rattles or makes noises when turning or going over bumps, it might be time to think about rebuilding your...

Reproduction bracket to mount the upper control arm to the frame on 2-wheel drive pickup, Blazer, and Jimmy models from 1963-72. This bracket is made from heavy-duty stamped steel just like the origiinal, and features the two...

Reproduction of the original upper control arms designed for use with 1963-70 Chevrolet and GMC truck models. These upper contro arms are manufactured to original factory specifications from heavy gauge steel replicating the...

This industry-exclusive Boxed C-Notch set is installed inside the frame rail and can installed without bed removal. This is highly recommended if you are lowering the rear of your C-10 4" or more so you do not bottom out...

Reproduction bracket to mount the upper control arm to the frame on 2-wheel drive pickup, Blazer, and Jimmy models from 1963-72. This bracket is made from heavy-duty stamped steel just like the origiinal, and features the two...

Reproduction of the original upper control arm designed for use with 1963-70 Chevrolet and GMC Pickup, Suburban, Panel Truck, Crew Cab, Blazer and Jimmy 1/2 ton, 2 wheel drive models. Also fits 1970 Chevrolet G10/G20 Van, and...

Reproduction of the original style upper ball joint for use with 1963-70 Chevrolet and GMC trucks. If your suspension rattles or makes noises when turning or going over bumps, it might be time to think about rebuilding your...

Rear lowering blocks for 1960-72 Chevy C-10 pickups. This kit will lower the rear of a coil spring truck up to 1" while maintaining the vehicle's original shock angle, preserving ride quality and handling characteristics. ...

Rear lowering blocks for 1960-72 Chevy C-10 pickups. This kit will lower the rear of a coil spring truck up to 2" while maintaining the vehicle's original shock angle, preserving ride quality and handling characteristics. ...

Rear lowering blocks for 1960-72 Chevy C-10 pickups. This kit will lower the rear of a coil spring truck up to 1 1/2" while maintaining the vehicle's original shock angle, preserving ride quality and handling characteristics....

Reproduction of the original upper control arm bumper for 1960-72 Chevrolet and GMC 1/2 ton, 3/4 ton, and 1 ton truck models, and 1973-91 Chevrolet and GMC 3/4 ton and 1 ton truck models. Each bumper is manufactured in heavy...

Mustang II Coil Spring Ride Height Adjuster Kit.

Adjust vehicle height at the push of a button while maintaining balanced air springs. The RidePro E5 control system tunes air ride suspension for proper handling and world-class ride quality by way of sophisticated pressure...

This hex head sems tapping screw is #8 x 25/32" and has a 5/8-inch attached washer. Product Specifications: Hex head sems tapping screw Phosphate M4.2-1.41 x 20mm (#8 x 25/32") Washer O.D.: 16mm (5/8-inch) 7mm hex Replaces...

Designed to fit most leaf springs, these bars strengthen rear suspension and reduce wheel hop. They are constructed from heavy gauge rectangular steel and feature MIG welded brackets for extra strength. Rubber snubbers,...

This 5/16"-24 "Keps" lock washer and nut is zinc plated steel and is sold as each. Product Specifications:Keps lock washer and nut Zinc plated steel Thread size: 5/16"-24 Hex width: 1/2"

This stainless steel 5/16-inch flat washer is for use with 18-8 fasteners. Product Specifications: Stainless steel commercial flat washer Bolt size: 5/16-inch Inner diameter: 11/32-inch Outer diameter: 3/4-inch Approximate...

Prothane universal style greasable sway bar bushings for classic Mustang. These bushings feature have a grease fitting built into the heavy duty brackets for convenient lubrication and contoured grooves molded into the...

This 1/2"-13 zinc plated steel lock nut is sold as each.

7/16" F436 Washer. ASTM F436 covers the chemical and mechanical requirements for hardened washers in diameters ranging from 1/4? to 4? inclusive. These heat treated washers are for general purpose and structural use. For use...

This 1/4-inch stainless steel medium split lock washer is for use with 18-8 fasteners. Product Specifications: Stainless steel medium split washer Size: 1/4-inch Outer diameter: 31/64-inch Minimum thickness: .062-inch

Specifications: Diameter: 5/8" Width: 2-3/4" Length: 9" Features: Includes Nuts E-Coated For Corrosion Resistance Ductile Iron With Fixed Center Pins

Black phosphate coated hex head bolts with washer. Measures 3/8-16 x 1" SEMS with 1" outside diameter to fit a variety of applications, including the hood latch on 1970-81 Firebird, and 1973-80 Chevrolet or GMC truck, among...

This is a stainless steel 5/16-18x1-inch hex head cap screw that has many uses for your project vehicle. Specifications: Thread Size : 5/16-18 Length : 1" Thread Length : Partial Head Style : Hex Material : 18-8 Stainless...

Fits 25mm (1 Inch) Sway Bars Only

Adjust vehicle height at the push of a button while maintaining balanced air springs. The RidePro E5 control system tunes air ride suspension for proper handling and world-class ride quality by way of sophisticated pressure...

This 1/4-inch x 7/16-inch steel acorn cap nut is nickel plated. Product Specifications: Steel acorn cap nut Nickel plated Thread size:1/4"-20 Hex width: 7/16" Height: 3/8"

RidePro-HP ride height sensors upgrade your existing RidePro-X pressure-based system. The ultimate air suspension management system measures BOTH pressure and ride height. With the addition of RidePro-Hp ride height and...

Reproduction of the original molded rubber coil spring insulator that mounts between the coil spring and the frame. This insulator keeps the spring from riding metal-to-metal on the frame. Coil spring insulators were not...

Nut 7/16"-20 Grade 8 Hi .625 Tall, 11/16 Hex Head. Hex nuts are six-sided, internally threaded fasteners, mated with bolts, studs, screws, and other externally threaded products. The addition of the hex nut ensures that the...

Reproduction control arm bushing for the lower control arm on various 1971-05 GM and various other models. Manufactured in steel clad rubber to be pressed into place. If your suspension rattles or makes noises when turning...

Replacement push on round flat nuts used on various vehicles. Zinc plated. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is...

Rear Coil Over Shock Kit, Universal design allows installation on a variety of chassis. Complete kit includes 3 way Adjustable Shocks, Upper Mounts and Adjustable Lower Mounts. 3-Way Adjustable Shocks provide controlled squat...

Universal Polyurethane Sway Bar End Link Grommets and Washers Universal - Set of 8 Inner Diameter - 3/8" Nipple Outer Diameter - 11/16" Outer Diameter - 1-1/8" Height - 0.725"

Transmission Hex Bolt: Classic Industries offers this complete listing of the original factory 4/speed Muncie transmission as shown in the diagram. Although many of the parts are currently not available, we list them all....

Prothane universal style urethane sway bar bushings for classic Mustang. These firm polyurethane bushings will enhance roll bar effectiveness over mushy stock rubber bushings without compromising ride quality. They come...

Prothane universal style greasable sway bar bushings for classic Mustang. These bushings feature have a grease fitting built into the heavy duty brackets for convenient lubrication and contoured grooves molded into the...

Speed nuts for various original or reproduction emblems that include 5/16" mounting studs. This speed nut set can be utilized for many of the emblems that don't include attaching nuts. Set includes 4 speed nuts without...

Grade 5, size 7/16-14 USS hex nut, in zinc plated finish. Sold individually. Specifications: Screw Size : 7/16-14 Across Flats : 11/16" Grade : 5 S.A.E. Standard : J995 Finish : Zinc Proof Load : 120000 Rockwell Hardness :...