Product#: 3415

Bumper Bolt with Conical Keps Hex Nut; Polished Stainless Steel Capped Head; 3/4" Diameter; 3/8-16" x 1"; Zinc Plated

Reproduction GM bumper bolt for a variety of General Motors and Chrysler applications. Each zinc-plated steel carriage bolt features a polished stainless steel cap for superb cosmetic appearance, corrosion resistance and long...


Product#: 2710

Chrome Trim Screw, #8 x 3/4", With #8 Phillips Oval Head

Replacement chrome plated trim screws used on various GM vehicles. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is original...


Product#: 8610

Flat Washer; 1/2" USS; Zinc Plated

1/2" USS zinc plated Flat Washer for a variety of applications. A washer is a thin plate (typically disk-shaped) with a hole (typically in the middle) that is normally used to distribute the load of a threaded fastener, such...


Product#: 13757

1965-69 Impala, Camaro, Bel Air, Firebird; Hood Insulation Fastener; Black Nylon

Replacement black nylon 2" square head hood insulation retainer is just what your classic vehicle needs to keep your original hood insulation where it belongs...attached to the hood. This retainer is a service replacement for...


Product#: 10362

Bolt, 5/16-18 x 13/16" Pointed Tip With Hex Washer Head, Black Phosphate

OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. Note: For a money saving set of 10 use...


Product#: 3899508

1959-80 Trico Windshield Wiper Blade; 15" Length; Various Models; Each

Reproduction 15 inch "TRICO Style # PR-15-2W" wiper blade for a wide variety of classic vehicle models. Each blade features stainless steel construction and is loaded with a period-correct TRICO RF-15 style insert with a...


Product#: MM1143

1970-74; Challenger, Barracuda, Cuda; Hood Hinges; with Springs; Pair

Reproduction of the original 1970-1974 Plymouth Cuda hood hinges designed for 1970-74 Mopar E-body models. Each hood hinge is manufactured to exact factory specifications and includes OE style hood hinge springs. Get your...


Product#: K51020

1962-76 GM, Dodge, Plymouth; Various Models; Convertible Top Boot Vinyl Storage Bag

Why leave your top boot in the trunk exposed when you can keep it safe and clean by safely storing it in this special top boot vinyl storage bag. The storage bag will help protect your vehicles top boot while being stored in...


Product#: MM1015

1970-71 Plymouth Barracuda, Cuda; Rear Bumper; Without Jack Slots; Chrome; OER Premier; Show Quality

OER Premier chrome rear bumper for 1970-71 Plymouth Barracuda, Cuda models. This reproduction bumper is designed exclusively for the restorer who demands the best the market has to offer. Features superior triple chrome...


Product#: ME162701

1970-71 Challenger, Barracuda; Convertible Rear Window; Tinted Glass; Crush Vinyl; White

Reproduction convertible glass rear window, manufactured using high quality heavy weight sateen backed Crush Grain vinyl materials to ensure longevity and durability. Original manufacturing techniques assure that you receive...


Product#: MM1001

1970-71 Plymouth Barracuda; Front Bumper; Without Jack Slots; Chrome; OER Premier; Show Quality

OER Premier chrome front bumper for 1970-71 Plymouth Barracuda models. This reproduction bumper is designed exclusively for the restorer who demands the best the market has to offer. Features superior triple chrome plating...


Product#: MM1003

1973-74 Plymouth Barracuda; Front Bumper; With Jack Slots; Chrome; OER Premier; Show Quality

OER Premier chrome front bumper for 1973-74 Plymouth Barracuda models. This reproduction bumper is designed exclusively for the restorer who demands the best the market has to offer. Features superior triple chrome plating...


Product#: ME159901

1970-71 Dodge Challenger, Plymouth Barracuda; Convertible Top; Crush; White

Replacing your convertible top is an expensive proposition that should be done once and done right. Classic Industries® ; understands what a demanding job it is, that's why we stock the highest quality convertible tops...


Product#: MM1016

1972 Plymouth Barracuda, Cuda; Rear Bumper; With Jack Slots; Chrome; OER Premier; Show Quality

OER Premier chrome rear bumper for 1972 Plymouth Barracuda, Cuda models. This reproduction bumper is designed exclusively for the restorer who demands the best the market has to offer. Features superior triple chrome plating...


Product#: MM1002

1972 Plymouth Barracuda; Front Bumper; With Jack Slots; Chrome; OER Premier; Show Quality

OER Premier chrome front bumper for 1972 Plymouth Barracuda models. This reproduction bumper is designed exclusively for the restorer who demands the best the market has to offer. Features superior triple chrome plating that...


Product#: MM1017

1973 Plymouth Barracuda; Rear Bumper; With Jack Slots; Chrome; OER Premier; Show Quality

OER Premier chrome rear bumper for 1973 Plymouth Barracuda models. This reproduction bumper is designed exclusively for the restorer who demands the best the market has to offer. Features superior triple chrome plating that...


Product#: MM1018

1974 Plymouth Barracuda, Cuda; Rear Bumper; With Jack Slots; Chrome; OER Premier; Show Quality

OER Premier chrome rear bumper for 1974 Plymouth Barracuda, Cuda models. This reproduction bumper is designed exclusively for the restorer who demands the best the market has to offer. Features superior triple chrome plating...


Product#: DB4434T

1970-74 Plymouth; Barracuda, Cuda; Back Window Glass; Coupe; Tinited

Reproduction of the original style back window glass designed for use with 1970-74 Plymouth Barracuda, and Cuda models. Replace your missing, scratched or broken original vent glass with this new DOT (department of...


Product#: 11503957

U-Nut; M6 - 1.0; Panel Range.030" to.160"; Center of Hole to Edge: 17/32"; Black Phosphate; Each

Black phosphate metric u-nut or foldover nut, that measures M6-1.0 to install and secure various components. Fits panel thickness from.80mm to 4 mm. (.030" to.160") Specifications: OE #: 11503957 Quantity: Individual Clip...


Product#: HK234

1960-72 GM, Chrysler, Ford; Convertible Top Hydraulic Hose Set; with Power Top; White Hose; O.L.114"; Center to End 57-1/4"

Reproduction of the original hydraulic hose set designed for use with a wide variety of convertible models as listed. Finding an original hose for your early convertible is next to impossible. If you own a convertible model...