1970 Chevrolet Impala Parts - Brake Accessories

Use with power brake bleeder # 14227 for 1992-02 models with plastic master cylinder and a twist-lock cap.

This service replacement switch is for use with the GM applications listed below. This is a service replacement switch which may differ cosmetically from the original switch but will fit and function as original. ...

This low pressure hydraulic brake pressure switch from Ron Francis Wiring has a much longer life than previous models available anywhere. This unit fits most cars and requires 20-50 pounds pressure, instead of stock units...

Reseal your brake caliper with this repair set. 1 set required per piston. 2 sets required per vehicle. Buick Applications: 1975 Apollo 1975-77 Century 1991-96 Commercial Chassis 1975-78 Electra 1979 Electra Rear Drum...

This attractively designed fluid reservoir blends well with traditional or contemporary engine compartments. Fluid lines can be run out of the back or bottom of reservoirs 1/8" NPT (plugs included for unused holes). Made in...

This attractively designed fluid reservoir blends well with traditional or contemporary engine compartments. Fluid lines can be run out of the back or bottom of reservoirs 1/8" NPT (plugs included for unused holes). Made in...

This attractively designed fluid reservoir blends well with traditional or contemporary engine compartments. Fluid lines can be run out of the back or bottom of reservoirs 1/8" NPT (plugs included for unused holes). Made in...

This attractively designed fluid reservoir blends well with traditional or contemporary engine compartments. Fluid lines can be run out of the back or bottom of reservoirs 1/8" NPT (plugs included for unused holes). Made in...

This attractively designed fluid reservoir blends well with traditional or contemporary engine compartments. Fluid lines can be run out of the back or bottom of reservoirs 1/8" NPT (plugs included for unused holes). Made in...

Wilwood ten pound residual pressure valves retain a minimum brake line pressure to help eliminate excessive pedal travel in both disc and drum brake systems. With drum brakes, a ten pound valve is used to compensate for...

Wilwood pressure valves retain a minimum brake line pressure to help eliminate excessive pedal travel in both disc and drum brake systems. The two pound valve is used in disc brake applications where the master cylinder is...

Made out of aluminum, 2.44" ID. Used on Wilwood hats or rotors with center register diameters less than 3.06"

Now you can bleed your hydraulic braking system quickly and easily by yourself! "Speed Bleeders" simply replace your original bleeder screws at each wheel cylinder (drum brakes) or caliper (disc brakes). The patented,...

Now you can bleed your hydraulic braking system quickly and easily by yourself! "Speed Bleeders" simply replace your original bleeder screws at each wheel cylinder (drum brakes) or caliper (disc brakes). The patented,...

Now you can bleed your hydraulic braking system quickly and easily by yourself! "Speed Bleeders" simply replace your original bleeder screws at each wheel cylinder (drum brakes) or caliper (disc brakes). The patented,...

Now you can bleed your hydraulic braking system quickly and easily by yourself! "Speed Bleeders" simply replace your original bleeder screws at each wheel cylinder (drum brakes) or caliper (disc brakes). The patented,...

Now you can bleed your hydraulic braking system quickly and easily by yourself! "Speed Bleeders" simply replace your original bleeder screws at each wheel cylinder (drum brakes) or caliper (disc brakes). The patented,...

The Roll/Control Installation Kit is designed to be used in conjunction with most brake holding devices on American made vehicles. This kit contains brake lines and various brass fittings, connectors, adapters, unions and...

Proportioning valve pressure warning light socket and pigtail. Required when adding disc brake master cylinder and proportioning valve to hook up the brake warning light. Note:For use with part #PV71 only.

Reproduction of the original blue bleeder valve dust caps designed for use with various models from 1969-1978. These dust caps are installed in seconds on your brake bleeder screws to keep road debris and the elements from...

The Rotor and Hat Register Adapters are used to locate one-piece iron rotors and aluminum hat assemblies to vehicle specific hub or axle registers. Available in size ranges from 2.00? to 2.88? internal diameter. Requires...