1970 Chevrolet Impala Parts - Accelerator Components

This is a correct reproduction of the commonly missing or worn out accelerator return spring which mounts between the carburetor and water neck and helps to return the throttle to the closed position. Chevrolet Applications:...

OER® reproduction of the correct cable retainer used to hold the accelerator control cable. This retainer slips over the cable and clips into the hole on the accelerator pedal arm. Manufactured in injection molded plastic...

Reproduction of the original accelerator pedal rod support for use on the various applications listed. Each support is manufactured in injection molded ABS offering an exact replacement of the original. Applications:...

Direct-fit billet accelerator pedal from Lokar! Designed to replace the original pedal pad of CTS-V drive-by-wire pedal. Ideal for applications running an LS-series engine with the CTS-V drive-by-wire pedal. Features a curved...

Chrome plated bracket set for Chevy small block with throttle cable type linkage. May be used with either round or square mounts. No need to remove carburetor for installation and allows for full adjustment. {specs} ...

Correct reproduction accelerator pedal pad stainless trim plate for various 1965-71 GM vehicles. Each trim plate is manufactured in stamped stainless offering long lasting dependability and an authentic appearance. This...

Correct OER® reproduction of the original floor mounted accelerator pedal pad installed on various GM models. Each accelerator pedal pad is manufactured in quality hard EPDM rubber unlike the plastic service replacement...

Correct reproduction of the original accelerator pedal to firewall support screws designed for use with the various GM models listed below. This screwis used for mounting the accelerator lever firewall support to the...

This is the retainer bracket which holds the rear loop of the throttle return spring in place. This bracket which mounts on top of the coil bracket was used on 1968-70 Camaro, Nova, Impala, Bel Air, and Caprice models with a...

Reproduction of the original style Quadrajet throttle cable bracket designed for use with various 1968-72 Chevrolet models. Each cable bracket is manufactured in stamped steel to original factory specifications making this...

Reproduction of the original style Holley throttle cable bracket designed for use with various 1968-72 Chevrolet models. Each cable bracket is manufactured in stamped steel to original factory specifications making this...

OER® Authorized reproduction upper kickdown clip for models with powerglide automatic transmission. Connects the upper passing gear kickdown rod to the bellcrank assembly. Applications: 1967-69 Camaro with Powerglide...

OER® reproduction clip for a variety of different parts on 1955-81 GM vehicles. This clip was used to attach the throttle valve control rod, throttle lever rod swivel, and the upper and lower clutch push rods. Use as...

Edelbrock throttle, cruise control, and transmission kick down set for pre-1978 small block Chevy cars with a TH350, 200R4, or 700R4 transmission. Manufactured in stamped steel and either chrome or gold cadmium plated....

Edelbrock throttle, cruise control, and transmission kick down set for pre-1978 small block Chevy cars with a TH350, 200R4, or 700R4 transmission. Manufactured in stamped steel and either chrome or gold cadmium plated....

Required by many race sanctioning bodies and a great idea for any high performance car, this intake manifold mounted throttle return spring and bracket set provides positive throttle return. Mounts to intake manifold on...

Required by many race sanctioning bodies and a great idea for any high performance car, this intake manifold mounted throttle return spring and bracket set provides positive throttle return. Mounts to intake manifold on...

Chrome plated bracket is precision stamped for a secure attachment which prevents from rotating out of position. Features a slotted design to fit most applications. {specs} {fitment}

The Eliminator floor-mount gas pedal is precision crafted from billet aluminum and designed to eliminate routing cables through the firewall. Includes an adjustable aluminum splined shaft and stainless steel under-the-floor...

Billet accelerator pedal from Lokar! Designed to replace the original pedal pad of CTS-V drive-by-wire pedal. Ideal for applications running an LS-series engine with the CTS-V drive-by-wire pedal. Features a curved pedal pad...

Pedal floor spacers are recommended when installing the pedal on vehicles with thick carpet or under carpet padding. Made in USA

This billet aluminum cable bracket from Lokar mount to the side of your TPI intake plenum and allow you to install your Throttle and Kickdown cable. Made in USA

This throttle and transmission kickdown cable bracket set removes the guesswork when installing a Street Demon carburetor in almost any carbureted GM application. All brackets have a clear zinc coating for corrosion...

This billet aluminum cable bracket from Lokar mount to the side of your TPI intake plenum and allow you to install your Throttle, Kickdown, and Cruise Control cable. Made in USA

Lokar's answer to LT cable problems. Stainless Throttle and Kickdown Brackets replace factory brackets. Kits include stainless arm to mount on throttle body to operate kickdown. Designed to be used with Lokar's Tuned-Port...

Lokar throttle cable brackets are available for a variety of different motors including carbureted set ups, LS1, Ram Jet 350 & 502 and more. Carburetor brackets only fit Holley, Edelbrock, AFB, Quadrajet, Demon, & In-Line...

This billet aluminum cable bracket from Lokar mount to the side of your TPI intake plenum and allow you to install your Throttle, Kickdown, and Cruise Control cable. Made in USA

Black Billet Aluminum. Single Hole Stud For Throttle Cable Only. Lokar throttle cable brackets are available for a variety of different motors including carbureted set ups, LS1, Ram Jet 350 & 502 and more. Carburetor...

This throttle rod adapter removes the guesswork when installing a Street Demon carburetor using mechanical linkage in almost any carbureted GM application. All brackets have a clear zinc coating for corrosion protection and...

Lokar's answer to LT cable problems. Stainless Throttle and Kickdown Brackets replace factory brackets. Kits include stainless arm to mount on throttle body to operate kickdown. Designed to be used with Lokar's Tuned-Port...

Black Billet Aluminum. Dual Hole Stud For Throttle Cable & Cruise Control Cable. Lokar throttle cable brackets are available for a variety of different motors including carbureted set ups, LS1, Ram Jet 350 & 502 and more....

Black Billet Aluminum. Dual Hole Stud For Throttle Cable & Cruise Control Cable. Lokar throttle cable brackets are available for a variety of different motors including carbureted set ups, LS1, Ram Jet 350 & 502 and more....

This billet aluminum cable bracket from Lokar mount to the side of your TPI intake plenum and allow you to install your throttle cables. Made in USA Also available: 2 hole for throttle and kickdown 3 hole for throttle,...

Lokar throttle cable brackets are available for a variety of different motors including carbureted set ups, LS1, Ram Jet 350 & 502 and more. Finishes include stainless steel, black stainless steel & billet aluminum were...

Lokar throttle cable brackets are available for a variety of different motors including carbureted set ups, LS1, Ram Jet 350 & 502 and more. Finishes include stainless steel, black stainless steel & billet aluminum were...

This billet aluminum cable bracket from Lokar mounts to the side of your TPI intake plenum and allow you to install your throttle cable. Made in USA Black billet aluminum. Single hole stud for throttle cable only.

The Eliminator floor-mount gas pedal is precision crafted from billet aluminum and designed to eliminate routing cables through the firewall. Includes an adjustable aluminum splined shaft and stainless steel under-the-floor...

This billet aluminum cable bracket from Lokar mount to the side of your TPI intake plenum and allow you to install your Throttle and Kickdown cable. Made in USA

Lokar's answer to LT cable problems. Stainless Throttle and Kickdown Brackets replace factory brackets. Kits include stainless arm to mount on throttle body to operate kickdown. Designed to be used with Lokar's Tuned-Port...

This billet aluminum cable bracket from Lokar mounts to the side of your TPI intake plenum and allow you to install your throttle cable. Made in USA Black billet aluminum. Double hole stud for throttle and ickdown cable...

Lokar's answer to LT cable problems. Stainless Throttle and Kickdown Brackets replace factory brackets. Kits include stainless arm to mount on throttle body to operate kickdown. Designed to be used with Lokar's Tuned-Port...

Stomp on it in true retro style with this groovy barefoot accelerator pedal cover. This far out pedal cover takes you back to the sixties every time you drive your classic. Chrome cover mounts over your existing accelerator...

Lokar throttle cable brackets are available for a variety of different motors including carbureted set ups, LS1, Ram Jet 350 & 502 and more. Finishes include stainless steel, black stainless steel & billet aluminum were...

Black Billet Aluminum. Single Hole Stud For Throttle Cable Only. Lokar throttle cable brackets are available for a variety of different motors including carbureted set ups, LS1, Ram Jet 350 & 502 and more. Carburetor...

Lokar throttle cable brackets are available for a variety of different motors including carbureted set ups, LS1, Ram Jet 350 & 502 and more. Finishes include stainless steel, black stainless steel & billet aluminum were...

Lokar throttle cable brackets are available for a variety of different motors including carbureted set ups, LS1, Ram Jet 350 & 502 and more. Finishes include stainless steel, black stainless steel & billet aluminum were...

The Eliminator floor-mount gas pedal is precision crafted from billet aluminum and designed to eliminate routing cables through the firewall. Includes an adjustable aluminum splined shaft and stainless steel under-the-floor...

Lokar's answer to LT cable problems. Stainless Throttle and Kickdown Brackets replace factory brackets. Kits include stainless arm to mount on throttle body to operate kickdown. Designed to be used with Lokar's Tuned-Port...

Brushed Billet Aluminum. Dual Hole Stud For Throttle Cable & Cruise Control Cable. Lokar throttle cable brackets are available for a variety of different motors including carbureted set ups, LS1, Ram Jet 350 & 502 and more....

This billet aluminum cable bracket from Lokar mount to the side of your TPI intake plenum and allow you to install your throttle cables. Made in USA Also available: 2 hole for throttle and kickdown 3 hole for throttle,...

This billet aluminum cable bracket from Lokar mounts to the side of your TPI intake plenum and allow you to install your throttle cable. Made in USA Black billet aluminum. Triple hole stud for throttle, kickdown, and...

Universal style accelerator throttle rod designed for use on various GM, Ford, Chrysler, Dodge, Plymouth models. This accelerator rod is for use when modifications will not allow the use of the original rod between the...

This beautifully carved brushed billet aluminum throttle assembly has a spring-loaded pad like the OE design and features a splined removable lower arm for versatility in mounting to the right or left of the bracket. The...

Pedal floor spacers are recommended when installing the pedal on vehicles with thick carpet or under carpet padding. Made in USA

Gleaming polish not your style? Then take a look at this stealthy black anodized billet spring-loaded throttle assembly that features a removable lower arm and is splined for versatile mounting to either the right or left...

This beautifully carved brushed billet aluminum throttle assembly has a spring-loaded pad like the OE design and features a splined removable lower arm for versatility in mounting to the right or left of the bracket. The...

Some vehicles, especially vehicles with air conditioning, require a throttle solenoid to automatically increase engine rpm. This throttle solenoid set from Demon Fuel Systems includes the solenoid, bracket, and mounting...

The first spring loaded pedals in the industry! This chromed steel throttle assembly is spring loaded like the OE design, and features a removable, splined lower arm for versatile mounting to the right or left of the bracket...

Pedal floor spacers are recommended when installing the pedal on vehicles with thick carpet or under carpet padding. Made in USA

This beautifully carved brushed billet aluminum throttle assembly has a spring-loaded pad like the OE design and features a splined removable lower arm for versatility in mounting to the right or left of the bracket. The...