1970 Chevrolet Impala Parts - Body Gaskets & Seals

Reproduction of the original door frame weatherstripping designed for use on 1969-70 Impala and Full Size GM models. This replacement weatherstrip is designed to factory specifications and manufactured in E.D.P.M material to...

OER® reproduction of the original die-cut felt seals that slips over the bellcrank pivot studs and seals against the end of the bellcrank tube to prevent dirt and water damage. Manufactured to correct dimensions. Sold in...

Quality reproduction of the original outer door mirror gasket designed for use on various GM models. Manufactured to factory specifications in quality injection molded ABS, will fit original GM or reproduction mirrors....

Reproduction die-cut trunk lock cylinder gasket designed to seal the trunk lock cylinder to the body. This gasket is designed for use on the listings below. Each gasket will fit and function as original. This is a non-molded...

Reproduction of the original door lock gasket designed for use on various GM models including the listings below. After repainting your doors, or whenever replacing door locks, be sure to install new lock cylinder gaskets to...

Reproduction of the original outer door remote mirror mounting gasket for use with the various applications listed. Each gasket is manufactured to replicate the original is fitment and design. Can be used with the original...

This reproduction gasket set includes a complete set of door handle gaskets used to install the outer door handles on the various models listed below. Each set includes correct die-cut gaskets for both RH and LH outer door...

Reproduction of the original trunk lock cylinder gasket designed for use on various GM models. This gasket is used to seal the trunk lock cylinder to the body. Manufactured in quality EPDM molded rubber that replicates the...

Reproduction of the original style A-Arm seals designed to replace the old or worn out seals. The splash apron seals help keep your engine compartment clean and free of water, salt and other road hazards. Seals the engine...

Correct reproduction of the original U-shape rubber molded weatherstrip seal originally installed on 1969-70 Impala Custom, Caprice and convertible models. This seal attaches to the door jamb area under the quarter window...

Reproduction of the original style components required to replace and mount the outer door mirror on the door. Contains all the necessary hardware to install a standard outer door mirror onto either the drivers or passenger...

Reproduction of the original steering column seal that slides over the lower steering column where it protrudes through the firewall. Commonly melted or disfigured from fluids or other contaminants, this seal is highly...

Reproduction of the original fender or Quarter panel skirt rubber seal designed for use on various 1955-76 Chevrolet models. Manufactured to correct dimensions from quality EDPM rubber that replicates the original in fitment...

This reproduction door handle and door lock gasket set includes a complete set of door handle gaskets and door lock gaskets used to install the outer door handles and door locks on the various models listed below. Each set...

Seal your interior from water and other elements with these reproduction water shields. The shields should always be replaced when installing new door panels. Includes holes for door handles and window cranks.

1969-70 GM Full Size Vehicle rear door lock pillar seal for 4-door Hardtop. This part seals the bottom of the rear side window and may also be known as a door jamb seal Fully molded authentic rubber construction with metal...

Correct replacement of the original front door rubber bumper designed for use on 1967-1969 Camaro, Firebird, 1967-70 Impala, Full Size, 1968-79 Nova, X body 4 door models. Each bumper is replicated to the original OE...

Reproduction of the original round rubber floor pan plug installed on various 1955-76 General Motors vehicles. Found in various locations on the floor pan, these plugs are manufactured to factory specifications in quality...

Reproduction of the original style side hood rubber bumper designed for use various GM models. Over time, the rubber stoppers on your hood can wear out or deteriorate. These reproduction stoppers will help keep your hood...

Reproduction of the original rear rocker panel flaps for use on various Buick, Chevrolet, Pontiac, and Oldsmobile models. Once installed, these flaps will help prevent road splash and debris from entering and blocking the...

Reproduction of the original rubber stopper designed for use on the upper door section of the various GM models listed below. Each rubber stopper is manufactured to replicate the original in fitment and appearance. This...

Precision's weatherstrip lube significantly reduces friction, thereby reducing the installation force required to assemble parts & fittings. Helps to avoid injuries related to slippage and repetitive stress, reduces rejects,...

Correct staple to install fender skirt splash aprons for various models. 1/2" wide, 1/2" deep.