1970 Plymouth Belvedere Parts - Steering

Steering column knuckle rebuild kit for various 1965-93 Chrysler, Dodge, Plymouth models. Includes two shoes, two pins, and the rubber seal and retainer at the end of the coupler. This is a service replacement style part that...

Restorer's Choice reproduction of the lower steering column "swivel joint" seal and retainer is an exact duplicate of the original factory Mopar steering coupler. Features the correctly configured rubber seal (not a service...

If you're in the market to replace your worn out, damaged or missing power steering pump, choose a thoroughly reconditioned, carefully inspected and restored unit from Classic Industries. No core charge is required....

These sets come with all the bolts, washers and nuts required to mount the Saginaw power steering pump including the unique black studs that have been out of production for years: plus the special lock nut for the pulley on...

Steering universal joint & vibration reducer in steel. Couples stock Mopar steering columns to MN7505 and MN7506 Mopar power steering boxes. Stock column must be cut and shortened for installation. Includes drill bit and roll...

Most people think this is a regular nut that can be found anywhere. Then they find out it isn't! This is a special nut that is very hard to come by or find. It is manufactured to solve this issue.

This remanufactured power steering box is given a "cool dip finish" to protect critical areas from rust without affecting fit and function before new o-rings and lip seals are installed to ensure leak-free performance. Unit...

Reproduction non-date coded power steering return hose for your Mopar. Includes the correct style 18" hose and 2 correct clamps.

Reproduction date coded power steering return hose for your Mopar. Includes the correct style 18" hose and 4 correct clamps. Replace that old cracked return hose with an authentic reproduction part. Mopar Authe ntic...

Replacement federal power steering brackets for 1970-72 Small Block engines with aluminum water pumps. These are for A/C and non-A/C applications. Replace those old rusted or missing brackets with new power steering brackets....

A leak in your power steering system can make a mess of your engine compartment, your driveway and garage floor. You can also burn up your power steering pump by driving your classic when it is low on fluid. Replace your worn out or cracked p ower steering hoses before big problems occur. The pressure hose connects from the power steering pump to the steering gear box inlet. Specifications: Hose Length: 38" Fitting: 5/16" Female S.A.E. Fitting: 3/8" M ale Inverted Flare Dodge Passenger Car Applications: 1970-72 Challenger V8-318ci 1970-72 Challenger V8-340ci 1970-72 Charger V8-318ci 1972 Charger V8-340ci 1 970-72 Coronet V8-318ci 1972 Coronet V8-340ci 1970-72 Dart V8-318ci 1970-72 Dart V8-340ci 1972 Monaco V8-360ci 1970-72 Polara V8-318ci 1971-72 Polara V8-360ci Plymouth Passenger Car Applications: 1970-72 Barracuda V8-318ci 1970-72 Barracuda V8-340ci 1970 Belvedere V8-318ci 1970-72 Duster V8-318ci 1970-72 Duster V8-340ci 1970-72 Fury V8-318ci 1972 Fury V8-360ci 1972 Road Runner V8-340ci 1970-72 Satellite V8-318ci 1972 Satellite V8-340ci 1971-72 Scamp V8-318ci

A leak in your power steering system can make a mess of your engine compartment, your driveway and garage floor. You can also burn up your power steering pump by driving your classic when it is low on fluid. OER®...

Note: 1966 and earlier Steering Gears had Nipples that were 1/2" and/or 5/8". You may receive a nipple either straight, or 45 degree, depending on supplies available. Applications: 196 7-76 A/B/E-Body with power steering

To complete installing your Ididit column in your Mopar to your steering gear box, you will need the proper U-joint for easy installation. 3/4" DD x 5/8"-36 Made in the USA

Brand new reproduction power steering box for 1962-72 A/B/E-body models engineered to OE specifications. Each unit is inspected, adjusted and hydraulically tested. All units are carefully packaged to insure safe arrival at...

Brand new Mopar replacement manual steering box for 1966-76 A, B, and E-Body models manufactured by Flaming River. Here is the answer to that sloppy old manual steering box. This small sector steel box features stronger parts than the origina l plus a quicker ratio (16:1). This unit will give you quicker turning and a feeling of more control of your Mopar. Important: This steering box has a smaller sector shaft and a smaller pitman arm may be required. Note: No further discounts apply. Applications: A-Body 1966-76 Valiant 1966-76 Dart 1966-69 Barracuda 1970-76 Duster 1971-76 Scamp 1969-76 Swinger 1971-72 Demon 1973-76 Dart Sport B-Body 1966-74 Charger 1969 Charger Daytona 1966-74 Coronet 1966-70 Belvedere 1966-74 Satellite 1968- 74 Road Runner 1968-71 Super Bee 1970 Superbird E-Body 1970-74 Barracuda 1970-74 Challenger 1970-74 'Cuda

Reproduction manual steering box for a wide variety of 1965-76 A/B/E-body models. These boxes have the correct size and splined output shaft so your original pitman arm can be installed. This box, produced in aluminum as...

Reproduction of the power steering pump cap designed for use with a variety of 1961-2005 GM, and Chrysler, Dodge, Plymouth models that included a Saginaw power steering pump. Each cap is manufactured in quality injection...

The lower steering column "swivel joint" seal is a reproduction of the original service replacement part for Mopar steering couplers. Will fit all 1960-76 Mopar models. {fitment}

These power steering pump brackets are designed for 1970-76 Mopar small block engines, fit both styles of Saginaw pumps and are compatible with or without AC applications. Must have an aluminum water pump. Includes correct...

Replacement federal power steering brackets for 1967-72 Big Block and Hemi engines with aluminum water pumps. These are for A/C and non-A/C applications. Replace those old rusted or missing brackets with new reproduction...

Reproduction manual steering box for a wide variety of 1965-76 A/B/E-body models. These boxes have the correct size and splined output shaft so your original pitman arm can be installed. This box, produced in aluminum as...

This coupler set simplifies installation and eliminates factory coupler when converting from power to manual steering. Includes a coupler to fit the manual steering box, a connecting shaft and a column universal joint. A...

EPAS Power Steering Kit for 1962-76 Dodge and Plymouth B-Body models. This complete kit includes a 60 amp electric motor unit, a prewired control module, and all the necessary hardware for installation. Features a built in...

Reproduction lower ball joint, with steering arm, for the lower control arm on a wide variety of Dodge and Plymouth models. If your suspension rattles or makes noises when turning or going over bumps, it might be time to think about rebuilding your front suspension. You no longer have to search for obsolete parts because we carry the parts you need to rebuild the suspension with Restorer's Choice™ premium replacements. Installs on the Right Hand (Passenger) Side. Dodge A-Body Applications: 1973-76 Dart Sport 1973-76 Dart Swinger Plymouth A-Body Applications: 1973-76 Valiant 1973-76 Duster 1973-76 Scamp Dodge B-Body Applications: 1962 Dart 1963-64 Dodge 330 1963-64 Dodge 440 1962-64 Polara 1962-64 Polara 500 1966-72 Charger 1965-72 Coronet Plymouth B-Body Applications: 1962-70 Belvedere 1962-64 Fury 1962-64 Sport Fury 1962-64 Savoy 1965-74 Satellite 1968-72 Road Runner 1970 Superbird Dodge E-Body Applications: 1970-74 Challenger Plymouth E-Body Applications: 1970-74 Barracuda 1970-74 'Cuda

These power steering pump brackets are designed for 1964-69 small block LA engines with cast iron water pump housings and TRW or Thompson pumps. Can be used with or without AC applications. Includes correct hardware to mount...

These power steering pump brackets are designed for 1969-76 Mopar big block engines and fit both styles of Saginaw pumps. Includes correct hardware to mount brackets to the power steering pump and attach the assembly to the...

This 11 piece set includes the o-rings, gaskets, seals, hardware and washers you will need to install a reservoir on your saginaw power steering pump. This set has chrome hardware that are designed to be used with a chrome...

This is the O-ring set for Saginaw power steering pumps. Includes 8 pieces to re-seal the pump to the reservoir. Does not include the shaft seal. Fits most Saginaw pumps through 1977 including Saginaw P series. {fitment}

This is the hose adapter fitting for Saginaw power steering gear box or pump. Straight, inverted flare zinc coated steel, 5/8"-18 to -6AN. Fits most Saginaw gear boxes or pumps 1960 through 1977 including Saginaw P series. ...

Having trouble finding the correct Mopar pulleys to complete your motor? We have the answer! This replacement pulley is available in original Chrysler styles for all popular engines, including big block combinations and for vehicles with and without op tions such as power steering or air conditioning. Middle Hole - 5/8" diameter This power steering pump pulley features a chrome finish. Applications: Saginaw keyed with nut style pump 1965-later Mopar B Engine with or without AC 1965-later Mopar RB Engine with or without AC 1965-later Mopar Hemi Engine with or without AC Can be used on 1970 and up small block engines but require spacer set MD472 07 (sold separately) for correct alignment. Important Warning Regarding Steering Pump Pulleys: Stock replacement, aftermarket stamped steel or cast iron pulleys are not designed to exceed 400 horsepower or 6 000 RPM. Using reproduction pulleys on engines that exceed these limits may result in catastrophic failure of the pulley, which can potentially cause severe damage to the engine, cooling system and body parts. Classic Industries® assumes no liability for damages caused by improper usage of pulleys. Be sure to install the pulley properly to avoid damage that can occu r from improper installation or exceeding recommended RPM and horsepower limits. {specs} Note: Pulley nut is not included.

MN7507 Mopar vibration reducing universal joint coupling to the shortened steering column shaft. Drill bit and pins included with coupler. Use MN7508 hose set for Saginaw pumps. Popular Applications: 1962-76 A/B/E-body with...

This 11 piece set includes the o-rings, gaskets, seals, hardware and washers you will need to install a reservoir on your saginaw power steering pump. This set has unfinished hardware that are designed to be used with a...

Authentic reproduction of the original power steering pressure control valve return fitting for the steering sector on 1967-74 various Dodge and Plymouth models. The return hose of the power steering pump attaches to this...

Brand new OER Authorized Mopar replacement manual steering box for 1966-76 A, B, and E-Body models. Here is the answer to that sloppy old manual steering box. This small sector cast iron box features a quicker ratio (16:1),...

This OER® power steering pump rebuild set designed for use with various AMC, Chrysler, GM, and Ford models that included a Saginaw power steering pump. This rebuild kit includes the essential parts needed to rebuild your...

OER Authorized power steering pump for use with various 1961-74 AMC, GM, and Mopar models with a Saginaw style power steering pump. Each pump is manufactured to correct OEM standard of quality. This new power steering pump is...

A modern power steering box for the 1962-1982 Chrysler, Plymouth, Dodge models. This box fits both factory power & manual steering cars. The Borgeson conversion box offers a 14:1 quick ratio, firm modern power steering feel,...

Replacement for the power steering return hose clamps for 1968-74 A, B and E-body models. These clamps have the correct red color as the original for those added judging points. Sold as a pair.

Reproduction style power steering pump designed for use with various 1969-74 Chrysler, Dodge, Plymouth models with 225, 318, 340, 360 engines. If you're looking for a power steering pump for your classic vehicle and are...

2 Piece OEM style rubber power steering hose kit. Connects Saginaw power steering pump to Mopar power steering box MN7505 and MN7506. V-8 applications only. Applications: 1962-76 A/B/E-body with MN7505 or MN7506 power...

This is the stud and bolt kit for Saginaw power steering pumps. Includes (2) studs (3/8"-16 thread), (1) bolt 3/8"-16 thread). Fits most Saginaw pumps through 1977 including Saginaw P series. This set is black phosphate...

This is the stud and bolt kit for Saginaw power steering pumps. Includes (2) studs (3/8"-16 thread), (1) bolt 3/8"-16 thread). Fits most Saginaw pumps through 1977 including Saginaw P series. This set is the chrome plated set...

This u-joint connects the Mustang II conversions with a manual steering rack to a 3/4" DD shaft that goes to the steering column. Applications: 1967-81 Camaro 1967-81 Firebird 1962-79 Nova 1968-72 A/ B/E-Body with Riley...

Service replacement power steering hose for various 1963-80 GM, Chrysler, Dodge, and Plymouth models. A leak in your power steering system can lead to a very serious and possibly dangerous situation. Leaking hoses can cause a...

Reproduction of the original style power steering return hose used on various GM and Dodge, Plymouth models as listed below. A leak in your power steering system can lead to a very serious and possibly dangerous situation....

Is your steering loose or front end out of alignment? Parts in your steering system may be worn out or damaged. Now you can rebuild your classic's steering linkage with this Restorer's Choice™ premium replacement. Sold individually. Two required per vehicle. Applications: A-Body 1970-76 Valiant 1970-76 Dart 1970-76 Duster 1971-76 Scamp 1970-76 Swinger 1971-72 Demon 1973-76 Dart Sport B-Body 1970-78 Charger 1970-76 Coronet 1970-70 Belvedere 1970-74 Satellite 1970-74 Road Runner 1970-71 Super Bee 1970 Superbird E-Body 1970-74 Barracuda 1970-74 Challenger 1970-74 'Cuda When purchasing reproduction parts and accessories from Classic Industries® you can be sure that each and every product displaying the Restorer's Choice™ symbol is manufactured correctly to exact specifications, fits the way the factory intended and is your assurance of quality.

Is your steering loose or front end out of alignment? Parts in your steering system may be worn out or damaged. Now you can rebuild your classic's steering linkage with this Restorer's Choice™ premium replacement. Sold individually. Two required per vehicle. Applications: A-Body 1970-76 Valiant 1970-76 Dart 1970-76 Duster 1971-76 Scamp 1970-76 Swinger 1971-72 Demon 1973-76 Dart Sport B-Body 1970-74 Charger 1970-74 Coronet 1970-70 Belvedere 1970-74 Satellite 1970-74 Road Runner 1970-71 Super Bee 1970 Superbird E-Body 1970-74 Barracuda 1970-74 Challenger 1970-74 'Cuda When purchasing reproduction parts and accessories from Classic Industries® you can be sure that each and every product displaying the Restorer's Choice™ symbol is manufactured correctly to exact specifications, fits the way the factory intended and is your assurance of quality.

Is your steering loose or front end out of alignment? Parts in your steering system may be worn out or damaged. Now you can rebuild your classic's steering linkage system with this aftermarket replacement. Sold individually. Two required per vehicle. A-Body 1970-76 Valiant 1970-76 Dart 1970-76 Duster 1971-76 Scamp 1970-76 Swinger 1971-72 Demon 1973-76 Dart Sport B-Body 1970-78 Charger 1970-76 Coronet 1970-70 Belvedere 1970-74 Satellite 1970-74 Road Runner 1970-71 Super Bee 1970 Superbird E-body 1970-74 Barracuda 1970-74 Challenger 1970-74 'Cuda

Is your steering loose or front end out of alignment? Parts in your steering system may be worn out or damaged. Now you can rebuild your classic's steering linkage with this Restorer's Choice™ premium replacement. Applications: B-Body 1968-72 Charger 1969 Charger Daytona 1968-72 Coronet 1968-70 Belvedere 1968-72 Satellite 1968-72 Road Runner 1968-71 Super Bee 1970 Superbird E-Body 1970-74 Barracuda 1970-74 Challenger 1970-74 'Cuda When purchasing reproduction parts and accessories from Classic Industries® you can be sure that each and every product displaying the Restorer's Choice™ symbol is manufactured correctly to exact specifications, fits the way the factory intended and is your assurance of quality.

Correct reproduction of the original idler arm assembly designed for use with various 1968-74 Dodge and Plymouth B and E body models. Each idler arm is manufactured in heavy cast material replicating the factory original in...

Quit searching for all the individual components you need when replacing your worn out wheel bearings and seals. Buy the complete kit to save time and money! Kit includes: Two inner wheel bearings with races Two outer wheel bearings with races Two wheel seals Note: No further discounts apply. Applications: A-Body 1960-61 Lancer 1965-72 Valiant with 10" dru m brakes 1965-72 Dart with 10" drum brakes 1964-69 Barracuda with 10" drum brakes 1970-72 Duster with 10" drum brakes 1971-72 Scamp with 10" drum brakes 1969-76 Swinger with 10" drum brakes 1971- 72 Demon with 10" drum brakes B-Body 1960-61 Dart, Phoenix 1967-72 Charger with 10" drum brakes 1969 Daytona with 10" drum brakes 1967-72 Coronet with 10" drum brakes 1968-71 Super Bee w ith 10" drum brakes 1960-61 Fury, Belvedere, Savoy 1967-70 Belvedere with 10" drum brakes 1967-71 GTX with 10" drum brakes 1967-72 Satellite with 10" drum brakes 1968-72 Road Runner with 10" drum brakes 1970 Superbird with 10" drum brakes

Repair torn and worn-out tie rod end boots without having to purchase the entire tie rod. Add durability surpassing most OEM rubber boots with this quality reproduction. Manufactured in high performance polyurethane for added...

Repair torn and worn-out tie rod end boots without having to purchase the entire tie rod. Add durability surpassing most OEM rubber boots with this quality reproduction. Manufactured in high performance polyurethane for added...

Fresh wheel seals are a must when repacking or changing your front wheel bearings. Sold each. {fitment}

These tubular tie rod adjusting sleeves are used in performance applications to provide 360 degree, full thread engagement on inner and outer tie rod threads. They are locked in position with jam nuts to stop the sleeve from rotating. Rather than a special tool, an open-end wrench is used for adjustments. Seals out dirt and water to provide superior holding ability under hard cornering. Sold as a pair. Made in USA Note: Discount exempt. Applications: A-Body 1963-76 Valiant 1963-76 Dart 1964-69 Barracuda 1970-76 Duster 1971-76 Scamp 1969-76 Swinger 1971-72 Demon 1973-76 Dart Sport B-Body 1963-64 Polara 1963-64 Polara 500 1963-64 Dodge 330 1963-64 Dodge 440 1966-72 Charger 1969 Daytona 1965-72 Coronet 1963-70 Belvedere 1963-64 Fury 1963-64 Sport Fury 1963-64 Savoy 1965-72 Satellite 1968-72 Road Runner 1968-71 Super Bee 1970 Superbird E-Body 1970-74 Barracuda 1970-74 Challenger 1970-74 'Cuda

If your Mopar small block has a Saginaw pump but no power steering pulley, this special bolt and spacer set is the solution! This set mounts big block power steering pulleys: MD2381, MD2382, MD2383, and MD2384 on your small...