Pertronix Flame Thrower 8-Cylinder 40,000 Volt 1.5 Ohm Black Oil Filled Ignition Coil
FEATURED

Product#: PX40011

Pertronix Flame Thrower 8-Cylinder 40,000 Volt 1.5 Ohm Black Oil Filled Ignition Coil

Complete your ignition upgrade with a Flame Thrower high performance ignition coil! The Flame Thrower coil fits into your existing coil bracket for a clean, factory look. Enables larger plug gaps for greater fuel efficiency...


Product#: 7720

MSD; Power Grid 7; Ignition Control Only

The Power Grid Ignition Control has been specially designed to mount to the Power Grid System Controller box, part #7730/77303. This Ignition output only controller packs higher output than the current programmable...


Product#: 77303

MSD; Power Grid System; Controller Only; Black

The Power Grid Ignition System is the next evolution of our Programmable 7-Series Ignition Controls. The Grid incorporates an efficient 32 bit microcontroller and an all new software program, called MSD View, and is USB...


Product#: 8253

MSD; Blaster HVC II Ignition Coil; Blue

The latest coil to be built entirely in house at MSD is designed to be used with MSD 6 and SCI Series Ignition Controls. This coil utilizes an iron U-Core design with a segmented bobbin for improved voltage distribution. The...


Product#: 75643

MSD; Stand Alone Solid State Relay Kit; 4 Channel; Black

Clean up your wiring with an MSD Solid State Relay Block. This module takes the place of 4 standard relays and eliminates unsightly wiring. 4 independent channels can be activated using either power or ground. Each channel is...


Product#: 8252

MSD; Blaster HVC Ignition Coil; Blue; Universal

Coils have always had to compromise voltage output against current output. More voltage increases the initial ionization of the spark plug gap, but lowers the amount of current, or heat, that follows across the plug gap. When...


Product#: 8732

MSD; Digital 2-Step Rev Control; For Digital 6AL

This 2-Step Rev Control could be added to give you the ability to switch to a low rpm limit to use on the starting line. Features two easy to read rotary dials that let you set the launch rpm in 100 rpm increments. There is...


Product#: PX60104

Pertronix 60,000 Volt 0.45 Ohm Flame Thrower HV Ignition Coil

The Flame Thrower HV (high voltage) coil has an E-Core design which is rated at a sizzling 60,000 volts and operates with no degradation of energy throughout the temperature ranges. Made from 6063 T5 aluminum, it...


Product#: PX60130

Pertronix 60,000 Volts 3.0 Ohm Flame Thrower HV Ignition Coil

The Flame Thrower HV (high voltage) coil has an E-Core design which is rated at a sizzling 60,000 volts and operates with no degradation of energy throughout the temperature ranges. Made from 6063 T5 aluminum, it...


Product#: 7740

MSD; Power Grid CAN-Bus 4-Hub Connector; Red

This hub allows you to expand the Power Grid system with up to four accessory modules.Note: This part is legal for use on Uncontrolled (Non-Emissions Controlled) Vehicles or Racing Vehicles.


Product#: 140001

Accel; 1955-74; 45,000 Volt; Super Coil; Ignition Coil

Replace your stock coil with an Accel high performance coil for increased performance, longer life and maximum dependability. {specs}


Product#: PX45111

Pertronix Flame Thrower II 4 -6 - 8 Cylinder 45,000 Volt 0.6 Ohm Black Epoxy Filled Ignition Coil

Complete your ignition upgrade with a Flame Thrower II high performance ignition coil! The Flame Thrower coil fits into your existing coil bracket for a clean, factory look. Enables larger plug gaps for greater fuel...


Product#: PX44001

Pertronix Flame Thrower III 8 Cylinder 45,000 Volt 0.32 Ohm Chrome Oil Filled Ignition Coil

The Flame Thrower III Coil is a rapid charge ignition coil to optimize the Ignitor III module. The Flame Thrower III is a traditional oiled filled canister for the "old school" appearance; but will work with modern day...


Product#: PX44011

Pertronix Flame Thrower III 8 Cylinder 45,000 Volt 0.32 Ohm Black Oil Filled Ignition Coil

The Flame Thrower III Coil is a rapid charge ignition coil to optimize the Ignitor III module. The Flame Thrower III is a traditional oiled filled canister for the "old school" appearance; but will work with modern day...


Product#: PX40111

PerTronix Flame Thrower 8 Cylinder 40,000 Volt 1.5 Ohm Black Epoxy Filled Ignition Coil

Complete your ignition upgrade with a Flame Thrower high performance ignition coil! The Flame Thrower coil fits into your existing coil bracket for a clean, factory look. Enables larger plug gaps for greater fuel efficiency...


Product#: PX45001

Pertronix Flame Thrower II 4 -6 - 8 Cylinder 45,000 Volt 0.6 Ohm Chrome Oil Filled Ignition Coil

Complete your ignition upgrade with a Flame Thrower II high performance ignition coil! The Flame Thrower coil fits into your existing coil bracket for a clean, factory look. Enables larger plug gaps for greater fuel...


Product#: PX40611

Pertronix Flame Thrower 6 Cylinder 40,000 Volt 3.0 Ohm Black Epoxy Filled Ignition Coil

Complete your ignition upgrade with a Flame Thrower high performance ignition coil! The Flame Thrower coil fits into your existing coil bracket for a clean, factory look. Enables larger plug gaps for greater fuel efficiency...


Product#: PX40001

Pertronix Flame Thrower 8 Cylinder 40,000 Volt 1.5 Ohm Chrome Oil Filled Ignition Coil

Complete your ignition upgrade with a Flame Thrower high performance ignition coil! The Flame Thrower coil fits into your existing coil bracket for a clean, factory look. Enables larger plug gaps for greater fuel efficiency...


Product#: 8145

Accel; 1955-74; Yellow; 45,000 Volt; Superstock Breakerless Electronic Ignition Coil

Replace your stock coil with an Accel high performance coil for increased performance, longer life and maximum dependability. {specs}


Product#: H556152

Holley; Sniper; HyperSpark Ignition Coil

Sniper EFI HyperSpark ignition coil from Holley. This coil features an innovative connector and integrated bracket for a secure connection and simplified mounting. Its powerful 135mj of spark ensure complete combustion and...