Product#: MM3059

1969-74 Chrysler 8-3/4" With 1-7/8 Pinion Stem Master Bearing Set

Yukon master overhaul kit for Chrysler 8.75" rear ends. Included in this kit are Timken carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, oil...


Product#: MM3089

Mopar 8-3/4" Differential Cast Iron 10-Spline Rear Yoke (Uses 7260 Series Strap Retained U-Joint)

This cast iron yoke is manufactured specifically for Mopar differentials. Includes the yoke, and mounting hardware. Important: Use MM3311 s trap kit, Note: Uses 7260 series U-joint (sold separately) that have a 2.125"...


Product#: MM3108

8-3/4" Adjustable Pinion Snubber

If you are using your stock leaf spring rear suspension and you have added horsepower to your engine; then you need to add an adjustable pinion snubber. This helps control axle windup by adjusting the height to the floor pan....


Product#: MN3361

Dana 60 Chrome Hex Head Differential Cover Bolt Set

This set is for use on Dana 60, or any other rear end using 3/8"-16 x 3/4" bolts. Includes 12 chrome finished bolts and 12 Flat washers (not chromed).


Product#: MN3161

1960-76 Mopar Rear End Housing E-Brake and Brake Line Clip Set

Reproduction rear and housing e-brake, and brake line clip set for all 1960-76 models. Replace your rusted originals with these correct replacements. Must be welded to the factory locations.


Product#: MD7114

Axle Nut Locking Pawl

This locking pawl and flanged nut is used on the right side axle of 8-3/4" and 9-3/4" differentials. The pawl secures the axle end play adjusting nut once proper bearing play is established.

Axle Nut Locking Pawl

MSRP $13.99 ea
Classic $11.99 ea

Product#: MM3058

1960-69 Chrysler 8-3/4" With 1-3/4 Pinion Stem Master Bearing Set

Yukon master overhaul kit for Chrysler 8.75" rear ends. Included in this kit are Timken carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, oil...


Product#: MM3092

Mopar 8-3/4" Differential Billet Steel 10-Spline Rear Yoke (Uses 1350 Series U-Bol Retained U-Joint)

This billet steel yoke is manufactured specifically for Mopar differentials. Includes the yoke, and mounting hardware. Important: Use MM3307 u-bolt kit, Note: Uses 1350 series U-joint (sold separately) that have a...


Product#: MM3057

1960-72 Chrysler 8-3/4" With 1-3/8 Pinion Stem Master Bearing Set

Yukon master overhaul kit for Chrysler 8.75" rear ends. Included in this kit are Timken carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, oil baffles and...


Product#: MM3093

Mopar 8-3/4" Differential Forged Steel 10-Spline Rear Yoke (Uses 1350 Series Strap Retained U-Joint)

This forged steel yoke is manufactured specifically for Mopar differentials. Includes the yoke, and mounting hardware. Important: Use MM3310 strap kit, Note: Uses 1350 series U-joint (sold separately) that have a...


Product#: MM3094

Mopar 8-3/4" Differential Billet Steel 29-Spline Rear Yoke (Uses 1350 Series U-Bol Retained U-Joint)

This billet steel yoke is manufactured specifically for Mopar differentials. Includes the yoke, and mounting hardware. Important: Use MM3307 u-bolt kit, Note: Uses 1350 series U-joint (sold separately) that have a...


Product#: MM3100

1975-2000 Mopar; 8-1/4" Rear End; Master Bearing Set With Timken Bearings

Motive Gear master bearing overhaul set for Chrysler 8.25" rear ends. Included in this set are Timken carrier bearings and races, pinion bearings and races, pinion seal, complete shims, ring gear bolts, pinion nut, crush...


Product#: FDM101

Filtermag; Rear Differential Filter Magnet

FilterMag powerful rare-earth magnet traps and holds wear inducing metal particles smaller than 40-microns down to 1-micron. The super-strong magnetic force holds FilterMag to the cover, is reusable and will reduce...


Product#: AR43732

5/16"-18 X 3/4" ARP Stainless Steel Differential Cover Bolt Set

Enhance the appearance of your rear end with ARP's stainless steel rear cover bolts. These bolts add a lustrous contrast to a painted OEM cover, compliment a chrome plated aftermarket version or add flash to that cast...


Product#: MD7120

Differential Pinion Thrust Spacer Set

Replacement thrust spacer set for 8-3/4" differentials with clutch type Sure-Grip prior to 1970. Required to provide axle thrust surface in four-spider differential applications. One set required per vehicle.


Product#: MN8060

1962-76 Mopar Differential ; Crush Sleeve Kit ; for 9-1/4"

Replacement crush sleeve for setting up your rear axle. Crush sleeves cannot be reused if you are changing a ring and pinion or the front seal. Includes pinion nut washer and pinion flange nut. These are for the 9-1/4"...


Product#: MM3114

Dana 60 Axel Cast Iron 29-Spline Rear Yoke (Uses 1330 Series U-Bolt Retained U-Joint)

This cast iron reproduction yoke is manufactured specifically for Dana 60 rear axles. Includes the yoke, retaining u-bolt, and mounting hardware. Note: Uses 1330 series U-joints (sold separately) that have a 3.625 " snap...


Product#: MM3118

Dana 60 Axel Forged Steel 29-Spline Rear Yoke (Uses 1350 Series U-Bolt Retained U-Joint)

This forged steel reproduction yoke is manufactured specifically for Dana 60 rear axles. Includes the yoke, retaining u-bolt and mounting hardware. Note: Uses 1350 series U-joint (sold separately) that have a 3.62 5" snap...