1973 Lincoln All Models Proform Auto Parts

Extended length fittings that can be easily tightened for an exact seal without damaging the fuel bowl. Each kit comes with 1 inlet fitting. {fitment}

If you don't have hours to spend accumulating all these small parts, then PROFORM's performance rebuild kit is the perfect solution. The kit includes two size 110 machined needle and seat assemblies, needle and seat...

This reversible fan helps prevent overheating in stop-and-go traffic, designed to fit the most popular cars and trucks, increases gas mileage, improves engine performance, frees the water pump pulley for more RPM, installs in...

Make plumbing your vehicle a breeze with these Proform individual AN Hose End wrenches. Made from quality anodized aluminum, they include short handles to avoid over-tightening and are sized to provide a comfortable grip....

These Proform AN adjustable wrenches are constructed from billet aluminum and are easy to adjust. They're the perfect non-marring tools for underhood plumbing work. This pair of adjustable wrenches includes a 3 AN-8 AN...

Beautiful high polished chrome cap including the embossed Bow Tie on top. 3 diameter. Includes non asbestos gaskets. For use on 1.22 holes.

This important tool makes installing the lower distributor drive shaft bushing into the engine block and subsequent reaming a snap. Simply tighten down to install the bushing, and spin the tool on the way out for a clean...

Your stock fan robs your engine of up to 15 or more horsepower! Replace it with a rugged, quieter than straight-blade, universal-fit S-blade fan equipped with an adjustable 160-240F. thermostat. Bolts to your radiator...

Chevrolet Performance 2 1/2” die cast aluminum breather caps. These push-in style breathers feature a unique Slant Edge design with the “Bowtie” emblem either raised or recessed into the aluminum. They are available in a...

Beautiful high polished chrome cap including the embossed Bow Tie on top. 3 diameter.

Precision machined for exacting fuel flow with larger stem base on the needle for accurate response to float arm movement. For gasoline applications with Viton tip. {fitment}

PROFORM's steel lift plate fits most Holley 2 barrel and 4 barrels as well as the Dominator. {fitment}

This popular clamp-on filter air breather, with the raised Bowtie Emblem stamped prominently in the top, is offered in one style: with the heat-shield hood. NOTE: GM's Oil Baffle Tube that simply pushes into a standard...

With this all-in-one tool, you will no longer need to using a ruler to measure spring height. Simple set the spring height with the highly refined measurement micrometer tube (0.01in increments), put it in the vise and start...

These custom valve cover mini nuts feature a Bowtie logo on the top of each fastener. Separate studs are included for precise gasket positioning. The wing nuts fit Chevrolet Big-Block, Small-Block, and V6 cylinder heads. Sold...

These custom valve cover mini nuts feature a Bowtie logo on the top of each fastener. Separate studs are included for precise gasket positioning. The wing nuts fit Chevrolet Big-Block, Small-Block, and V6 cylinder heads. Sold...

Primary metering block for all 2300, 4150, 4160 models except carburetors with an accelerator pump transfer tube or reverse idle mixture system. Uses standard fuel bowl and metering block gaskets. Timed spark or ported vacuum...

If you don't have hours to spend accumulating all these small parts, then PROFORM's performance rebuild kit is the perfect solution. The kit includes two size 110 machined needle and seat assemblies, needle and seat...

Billet Aluminum. Precision fit. Won't damage expensive AN fittings. {fitment}

Measure the proper pushrod length with these simple length checkers. Simply unscrew the adjustable end until it's the right length, then take it out and measure. Don't chance destroying your valve train because of improper...

This will go over cylinder bores up to 4-1/2in. This is used to check piston-to-deck clearance, and it is magnetic so it holds firmly in place. Dial indicator 66962 is sold separately. {fitment}

Make stud removal easier with our professional rocker arm stud remover tool. With ball bearing action and fittings for 5/16" and 3/8" this tool is a must have for all engine builders. {fitment}

Don't let a little tire pressure change affect you on race day! Quickly and easily gauge tire pressure with PROFORM's easy-to-use, hose equipped digital tire pressure gauge. Backlit digital display reads in Psi, Kpa, Bars,...

Time to replace your current air cleaner with a high quality MOPAR emblem air cleaner. This air cleaner uses the signature MOPAR blue emblem as seen in other like dress-up engine parts. The kit includes: 14" Black Crinkle...

Direct replacement components to turn a street carburetor into a high-performance carb: get that extra performance out of your ride in less than 30 minutes! Add up to 25-50 HP with PROFORM's 100% NEW, high-performance...

High compression engines run better with the spark plugs indexed. This way spark plugs can be properly set so there is no piston dome interference. {fitment}

Get your piston rings aligned the first time! Just simply press piston rings down for perfect depth every time. {fitment}

The PROFORM crank gear installation tool makes it easy to press gears on straight. Use this tool with PROFORM's harmonic balancer installer set, p/n 66514. {fitment}

Finally an affordable high-performance race carburetor! PROFORM’s Race Series Carburetor is hand assembled in Bowling Green, Kentucky utilizing the PROFORM High-Flow Carburetor Main Body, durable billet metering blocks,...

Accurately check spring height versus spring pressure with our new heavy-duty bench top spring tester. Check springs up to 2" in diameter and 4" in height. Can be bench or vise mounted. Test springs available at...

Replacement for Starter #66256, #66258, #66259, and other similar models {fitment}

Based on the highly successful Race Series carburetors, the PROFORM® street carburetor is constructed of lightweight aluminum, including provisions for a choke assembly and changeable idle air bleeds for easy,...

Let's face it, connecting rods rarely come apart easily. That is until now. Quickly loosen the cap from the rod without damage using PROFORM's new Heavy-Duty Rod Splitting Tool. Simply remove the rod nuts, place the rod onto...

Give your center nut style air cleaner an exciting new look with a prominent Extra-Large Bowtie Center Nut. The 3D contoured design with sleek slanted edges, chrome finish and gold Bowtie center, gives this center nut a bold...

No more jumping from under the hood, to the front seat, to under the hood! Easily test your engine with the PROFORM Remote Starter Switch. {fitment}

PROFORM Grade 8 (12.9 steel) header bolts are designed to keep bolts from backing off. These permanently assembled bolts feature special washers with super-hardened serrated teeth that, when sufficiently torqued, the washers...

This will go over cylinder bores up to 4-1/2in. This is used to check piston-to-deck clearance. Does not have a magnetic base. Dial indicator 66962 is sold separately. {fitment}

Billet Aluminum. Precision fit. Won't damage expensive AN fittings. {fitment}

Never damage your metering blocks again! This new aluminum power valve remover tool makes power valve removal a snap. Simply place the tool over the power valve and give it an easy turn.

Based on the wildly popular original Race Series carburetors, PROFORM's Black Race Series Carburetors include a Black Diamond coating for enhanced fuel cooling. Each carburetor is hand assembled and tested in the U.S....

This dial indicator is great for the technical or accurate engine builder. Indicators are .001" graduation.

Top off your engine with an open element air cleaner for the ultimate in looks and maximum airflow. Each triple chrome plated air cleaner comes with a handsome tri-star wing nut to finish the look in style. Fits carburetors...

These popular push-in filter air breathers, with the raised Bowtie Emblem stamped prominently in the top, are offered in two styles: with the heat-shield hood and without. 3" diameter. Fits 1.22" holes {fitment}

Who would dare to modify piston domes or to fly-cut valve pockets without knowing how much material there is to work with? This simple tool includes a 0.001in dial indicator and a contact point that permits measurement of the...

PROFORM heavy-duty micrometer sets for all the popular applications and finally affordable for the weekend racer. PROFORM micrometers feature quick-lock levers, ratchet stops, carbide measuring tips, calibration accessories,...

Make plumbing your vehicle a breeze with these Proform individual AN Hose End wrenches. Made from quality anodized aluminum, they include short handles to avoid over-tightening and are sized to provide a comfortable grip....

Quickly check any 6 and 12 volt system with power on to locate shorts, grounds, and open circuits. {fitment}

Based on the highly successful Race Series carburetors, the PROFORM® street carburetor is constructed of lightweight aluminum, including provisions for a choke assembly and changeable idle air bleeds for easy,...

Our heavy-duty cylinder head work stand is a great way to hold your cylinder heads above your workbench while working on them. The adjustable arms allow you to set the proper height and maintain stability. {fitment}

This heavy-duty, simple-to-use, manual valve spring compressor makes short work of even monstrous springs. The compressor arm slides for adjustment, employing a locking pin for rapid, easy operation. {fitment}

The PROFORM tapered ring compressor is an affordable an easy way to install your pistons! By creating a slight squeeze on the piston ring the compressor eases the piston into the cylinder bore. Manufactured for engine blocks...

Range: 1.600" to 2.100". Measure installed valve spring height conveniently and accurately. Simply install the height micrometer instead of a valve spring, and then rotate the clearly engraved dial to expand the tool to seat...

Make plumbing your vehicle a breeze with these Proform individual AN Hose End wrenches. Made from quality anodized aluminum, they include short handles to avoid over-tightening and are sized to provide a comfortable grip....

This easy-to-use universal camshaft installation tool comes with five adapters for most domestic V-6 and V-8 engines including LS1 engines. {fitment}

Big Block Push Rod Sets: Heat treated one-piece pushrod sets for ôTall Deckö applications. Includes 16 pushrods in a clamshell package.

These Proform pushrods can give you the foundation you need for a reliable valvetrain. They are manufactured from 4130 chromoly heat-treated tubing with .065-inch wall thickness. Proform pushrods can be used with guideplates....

This billet aluminum LS valve spring compressor is universal, compact, activated with normal hand tools, and takes up almost no space in your toolbox. It will cut valve spring removal and replacement time to around 1-hour....

Used to adapt an air cleaner with a 5-1/8" opening to a carburetor with a 4-7/32" flange. Manufactured in rigid, heat resistant plastic.

If you are looking for the classic look for your valve covers, look no further. This black crinkle finish breather cap has the Omega "M" recessed in blue, and comes with a grommet for exact fit. Made from quality stamped...

If you're swapping your HEI, might as well use a nice hold-down clamp at the same time. This black billet aluminum clamp is meaty, and looks great. Heavy-Duty Machined Aluminum. Fits Chevrolet. S/B, V6/90, B/B. Includes...