Product#: CX1859

1973-80 Chevy Pickup, Blazer, Jimmy, Suburban; Front Bumper; Chrome; w/o Impact Strip Holes

OER® Authorized reproduction of the original chrome front bumper designed for use with 1973-80 Chevrolet and GMC truck models. This quality reproduction ftont bumper is manufactured to factory specifications featuring a...

Product#: DY90007Y

1973-86 C/K, 1987-91 R/V Pickup; Sliding Rear Window; Three-Panel Design; Privacy Tint

OER Authorized sliding rear window to fit 1973-86 Chevrolet/GMC C/K and 1987-91 R/V pickup models. Features a three panel design, self-locking latch, and a slim line frame to enhance visibility. Aluminum frames feature a...

Product#: 153174A

1967-87 Chevrolet, GMC Stepside Pickup Truck; Chrome Rear Bumper

Reproduction of the original chrome rear bumper designed for use with 1967-87 Chevrolet and GMC Stepside pickup truck models. Each bumper is manufactured to original factory specifications replicating the original in design,...

Product#: 3415

Bumper Bolt with Conical Keps Hex Nut; Polished Stainless Steel Capped Head; 3/4" Diameter; 3/8-16" x 1"; Zinc Plated

Reproduction GM bumper bolt for a variety of General Motors and Chrysler applications. Each zinc-plated steel carriage bolt features a polished stainless steel cap for superb cosmetic appearance, corrosion resistance and long...

Product#: 2710

Chrome Trim Screw, #8 x 3/4", With #8 Phillips Oval Head

Replacement chrome plated trim screws used on various GM vehicles. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is original...

Product#: 8610

Flat Washer; 1/2" USS; Zinc Plated

1/2" USS zinc plated Flat Washer for a variety of applications. A washer is a thin plate (typically disk-shaped) with a hole (typically in the middle) that is normally used to distribute the load of a threaded fastener, such...

Product#: 13757

1965-69 Impala, Camaro, Bel Air, Firebird; Hood Insulation Fastener; Black Nylon

Replacement black nylon 2" square head hood insulation retainer is just what your classic vehicle needs to keep your original hood insulation where it belongs...attached to the hood. This retainer is a service replacement for...

Product#: 3798372

1962-84 Windshield Washer Jar Cap ; Various GM Models

Reproduction of the original windshield washer jar cap designed for use on a variety of GM models including 1967-74 Camaro models. This cap is manufactured in injection molded ABS and replicates the original. Features correct...

Product#: 10362

Bolt, 5/16-18 x 13/16" Pointed Tip With Hex Washer Head, Black Phosphate

OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. Note: For a money saving set of 10 use...

Product#: 3899508

1959-80 Trico Windshield Wiper Blade; 15" Length; Various Models; Each

Reproduction 15 inch "TRICO Style # PR-15-2W" wiper blade for a wide variety of classic vehicle models. Each blade features stainless steel construction and is loaded with a period-correct TRICO RF-15 style insert with a...

Product#: K51020

1962-76 GM, Dodge, Plymouth; Various Models; Convertible Top Boot Storage Bag

Why leave your top boot in the trunk exposed when you can keep it safe and clean by safely storing it in this special top boot storage bag. The storage bag will help protect your vehicles top boot while being stored in the...

Product#: 153174B

1967-87 Chevrolet, GMC Pickup; Rear Bumper; Chrome; Stepside; OER Premier® Show Quality

OER Premier™ reproduction of the original chrome rear bumper designed for use on 1967-1987 Chevrolet and GMC Pickup truck models. This reproduction bumper is designed exclusively for the restorer who demands the best...

Product#: 11503957

U-Nut; M6 - 1.0; Panel Range.030" to.160"; Center of Hole to Edge: 17/32"; Black Phosphate; Each

Black phosphate metric u-nut or foldover nut, that measures M6-1.0 to install and secure various components. Fits panel thickness from.80mm to 4 mm. (.030" to.160") Specifications: OE #: 11503957 Quantity: Individual Clip...

Product#: T70592

1973-84 Chevrolet/GMC Truck, Blazer, Jimmy, Suburban; Windshield Wiper Arm; LH Or RH

OER® Authorized reproduction bayonet style windshield wiper arm for all 1973-84 Chevrolet & GMC truck models including Suburban, Crew Cab, Blazer, and Jimmy. Each wiper arm is manufactured to OE factory specifications in...

Product#: A1017

3/8"-16 x 15/16" Bumper Bolt With Flat; Zinc Plated Shank; Stainless Steel Flat Head; Each

Correct replacement style bolt to replace the original missing or damaged bumper bolt. Each bolt is manufactured to original specifications and will match the original. Fits a variety of different years and models. Measures...

Product#: 6272581

1973-91 Chevy, GMC Pickup, Blazer, Jimmy, Suburban; Exterior Door Handle; Chrome; LH; Drivers Side

Reproduction outer door handle for 1973-86 Chevrolet and GMC C/K and 1987-91 R/V pickup, Blazer, Jimmy, and Suburban models. This beautiful, chrome plated reproduction is perfect for any early restoration. Includes door...

Product#: 6272582

1973-91 Chevy, GMC Pickup, Blazer, Jimmy, Suburban; Exterior Door Handle; Chrome; RH; Passenger Side

Reproduction outer door handle for 1973-86 Chevrolet and GMC C/K and 1987-91 R/V pickup, Blazer, Jimmy, and Suburban models. This beautiful, chrome plated reproduction is perfect for any early restoration. Includes door...

Product#: T70327

1973-80 Chevy,GMC Pickup, Blazer, Jimmy, Suburban; Hood Hinge; LH Driver Side

Reproduction of the original hood hinge assembly for 1973-80 Chevrolet & GMC pickup, Blazer, Jimmy, and Suburban models. Each hood hinge is manufactured from quality stamped steel assuring a quality replacement. This hood...

Product#: A3102

1957-87 GM; Bumper Bolt & Nut Stainless Steel 1/2"-13 x 1-1/2"; Low Dome; Various Models

Replacement style stainless steel capped bumper bolt and nut designed for use on many GM vehicles. Each bolt measures 1/2"-13 x 1-1/2"; 1-1/8" head diameter and comes complete with attaching nut. Can be used for a wide...

Product#: T1455

1954-87 Chevrolet/GMC Stepside; Rear Roll Pan; With License Plate Pocket; Without License Lamps

Customize the rear end of your classic Chevrolet or GMC stepside pickup truck with a sleek looking steel rear roll pan. This all steel roll pan is just what you need to add a cutom appearance. Manufactured in stamped steel...