1974 Plymouth Duster Parts - Carburetor Components

Correct style rod clip used on various GM vehicles. Fits 1/4" rod diameter, RH, 17/64" ID. These reproduction transmission linkage rod clips need to be replaced when replacing your linkage rods. 1955-57 Chevrolet...

Reproduction set of the original 2-1/2" flat blade carburetor fuel bowl screws for Holley carburetors. These special screws are specifically designed in the correct original configuration with the proper head design for the...

Die-cut reproduction air cleaner to carburetor gasket manufactured for use with any 2 bbl or 4 bbl carburator with a 5-1/8" base. Can be used with any small or big block engine. Fits most 1964 and newer Ford applications,...

The Edelbrock part #6593 Narrow Band LED Air-Fuel Ratio Monitor was designed for use with all aftermarket carburetor and EFI kits. The kit comes complete with an LED light display, oxygen sensor, sensor bung and wire harness....

Direct replacement components to turn a street carburetor into a high-performance carb: get that extra performance out of your ride in less than 30 minutes! Add up to 25-50 HP with PROFORM's 100% NEW, high-performance...

Direct replacement components to turn a street carburetor into a high-performance carb: get that extra performance out of your ride in less than 30 minutes! Add up to 25-50 HP with PROFORMs 100% NEW, high-performance...

Upgrade your carb with PROFORM new Billet Throttle Base Plate! Made from solid billet construction versus die cast aluminum for added strength and durability this base plate comes with button torx head throttle plate screws,...

Upgrade your carb with PROFORM's new Billet Throttle Base Plate! Made from solid billet construction versus die cast aluminum for added strength and durability this base plate comes with button torx head throttle plate...

Lokar Duo-Pak throttle cable set will easily adapt to most gas pedals and throttle assemblies. Cable comes equipped with aluminum fittings and aluminum ferrules to eliminate fraying and feature a "U-Cut-to-Fit" outer housing...

Lokar billet aluminum carburetor bracket and return spring kit for Edelbrock Carburetors. It attaches to both rear carb bolts to eliminate movement and ease the installation of Lokar?s throttle and kick down cables. Made...

Lokar Duo-Pak throttle cable sets will easily adapt to most gas pedals and throttle assemblies. Cable comes equipped with aluminum fittings and aluminum ferrules to eliminate fraying and feature a "U-Cut-to-Fit" outer housing...

Lokar Duo-Pak throttle cable set will easily adapt to most gas pedals and throttle assemblies. Cable comes equipped with aluminum fittings and aluminum ferrules to eliminate fraying and feature a "U-Cut-to-Fit" outer housing...

The Lokar Billet Aluminum Throttle/Kickdown Cable Mounting Bracket for Street Demon™ Carburetors is CNC machined from 6061-T6 billet aluminum. It provides easy installation of Lokar?s Throttle and Kickdown Cables. ...

Looking for an inexpensive replacement aluminum baseplate for you carburetor? PROFORM's new cast aluminum base plates are an inexpensive way to replace your existing plate, though we'd strongly suggest you consider upgrading...

Looking for an inexpensive replacement aluminum baseplate for you carburetor? PROFORM's new cast aluminum base plates are an inexpensive way to replace your existing plate, though we'd strongly suggest you consider upgrading...

This Lokar Hi-Tech "U-Cut-to-Fit" polished stainless steel outer housing with a "U-Cut-to-Fit" stainless inner wire throttle cable is designed with a specially extruded liner for extended service life and innovative clevis...

This Lokar Hi-Tech "U-Cut-to-Fit" outer housing with a "U-Cut-to-Fit" stainless inner wire throttle cable is designed with a specially extruded liner for extended service life and innovative clevis cable ends to eliminate the...

This Lokar Hi-Tech "U-Cut-to-Fit" outer housing with a "U-Cut-to-Fit" stainless inner wire throttle cable is designed with a specially extruded liner for extended service life and innovative clevis cable ends to eliminate the...

This Lokar Hi-Tech "U-Cut-to-Fit" outer housing with a "U-Cut-to-Fit" stainless inner wire throttle cable is designed with a specially extruded liner for extended service life and innovative clevis cable ends to eliminate the...

Primary metering block for all 2300, 4150, 4160 models except carburetors with an accelerator pump transfer tube or reverse idle mixture system. Uses standard fuel bowl and metering block gaskets. Timed spark or ported vacuum...

This Lokar Hi-Tech "U-Cut-to-Fit" outer housing with a "U-Cut-to-Fit" stainless inner wire throttle cable is designed with a specially extruded liner for extended service life and innovative clevis cable ends to eliminate the...

Lightweight aluminum center-hung fuel bowls with sight glass windows for easy visual float adjustment. Kit comes with two (2) fuel bowls and two (2) gaskets and anodized aluminum 5/8" x 18 inverted flare fuel inlets. Fits...

This Lokar Hi-Tech "U-Cut-to-Fit" outer housing with a "U-Cut-to-Fit" stainless inner wire throttle cable is designed with a specially extruded liner for extended service life and innovative clevis cable ends to eliminate the...

During hard acceleration the float bowls in a carburetor become uneven, causing moderate fuel starvation. This aluminum spacer tilts the carburetor forward 5 degrees to help keep it level. Spacer measures .830" at it's...

If you don't have hours to spend accumulating all these small parts, then PROFORM's performance rebuild kit is the perfect solution. The kit includes two size 110 machined needle and seat assemblies, needle and seat...

If you don't have hours to spend accumulating all these small parts, then PROFORM's performance rebuild kit is the perfect solution. The kit includes two size 110 machined needle and seat assemblies, needle and seat...

Reproduction phenolic carb spacers for all 2-4 inline AFB carburetors. Manufactured to factory specs featuring original style thickness and correct size openings.

Carburetor spacer kits are now available for Holley carburetors. Each kit includes mounting hardware and gaskets.

Reproduction throttle bracket for Mopar models equipped with a 361/383 engine, and 2x4 inline carburetors. Features the correct shape for a proper for a proper fit.

The Edelbrock #3578 Air Temp Sensor is for push in connections. This Edelbrock #36018 Air Temp Sensor includes a rubber grommet and has a range from -40 to 284 Deg Fahrenheit.

Replacement hood scoop-to-filter seals for 1970-74 A body Dart, Demon & Duster models. These are the rubber hood seals that connect the filter to the scoop on A-body models equipped with scoop hoods. Fits the factory approx....

Reproduction throttle return springs for all Mopar models equipped with a 2-4 inline or Long Ram carburetor set up. Manufactured to factory specs featuring the correct length and tension.

This stainless steel bracket mounts to rear of Holley, Edelbrock, AFB, Quadrajet, Demon, and in-line dual quads. Bracket is used to mount Lokar?s throttle cable and kickdown assemblies. This design provides improved...

Correct reproduction float bowl screw set for Holley carburetors. Each set includes the proper length screws (4 long & 8 short) in the correct original zinc dichromate finish for an authentic period-correct cosmetic...

Carburetor linkage studs for various models. These studs are used to connect the throttle cable, return spring, and transmission kick-down linkage to the carburator. Features correct stud with cadmium or zinc phosphate...

This throttle lever adapter fits 1966 and later vehicles to correctly adapt Performer and Thunder Series carburetors for use with the original cables. Features a black finish and works with vehicles equipped with cruise...

Replacement round head solenoid plunger for various Mopar models.

Carburetor linkage studs for various models. These studs are used to connect the throttle cable, return spring and transmission kick-down linkage to the carburator. Feature correct cadmium or zinc phosphate plating, include...

Carburetor linkage studs for various models. These studs are used to connect the throttle cable, return spring and transmission kick-down linkage to the carburator. Feature correct cadmium or zinc phosphate plating, include...

Carburetor linkage studs for various models. These studs are used to connect the throttle cable, return spring and transmission kick-down linkage to the carburator. Feature correct cadmium or zinc phosphate plating, include...

Carburetor linkage studs for various models. These studs are used to connect the throttle cable, return spring and transmission kick-down linkage to the carburetor. Feature correct cadmium or zinc phosphate plating, include...

Precision machined for exacting fuel flow with larger stem base on the needle for accurate response to float arm movement. For gasoline applications with Viton tip.

Fits all PROFORM carburetors and all Holley vacuum secondary carburetors except six pack, 3 bbl, and early Mopar applications.

Replacement carburetor linkage stud nut for all Mopar 1966-70 models. Each nut is unique for the years specified, the early style nut features a conical spin washer and recessed thread end. The later style nut has a stamped...

Replacement carburetor linkage stud nut for all Mopar 1970-76 models. Each nut is unique for the years specified, the early style nut features a conical spin washer and recessed thread end. The later style nut has a stamped...

Replacement idle solenoid wire connector boot for various Mopar models.

We now offer a variety of stud sets to fit just about any Holley or Rochester carburetor. Set includes: 4 studs 4 nuts 4 washers For 1-3/8" set see Part # T2046 For 2" set see Part # T2047

Replacement choke rod clip used to secure the thermostatic choke rod to the air valve lever on all Mopar applications. Manufactured from correct gauge spring steel material and finished in black oxide. Measures 1/8" and wil...

Replace the missing or damaged air cleaner mounting hardware on your Mopar with our correctly manufactured replacement stud. Each stud features original phosphate finish with correctly formed thread lengths on each end for a...

For all carburetors that require a vacuum fitting for a 5/32" tube.

Direct replacement components to turn a street carburetor into a high-performance carb: get that extra performance out of your ride in less than 30 minutes! Add up to 25-50 HP with PROFORM's 100% NEW, high-performance...

The Edelbrock Idle Compensator Kit #8059 is designed for use with Edelbrock AVS2, Performer and Thunder series AVS carbs. This Edelbrock Idle Compensator kit maintains correct idle speed when the air conditioning is on. The...

Direct replacement components to turn a street carburetor into a high-performance carb: get that extra performance out of your ride in less than 30 minutes! Add up to 25-50 HP with PROFORMs 100% NEW, high-performance...

Direct replacement components to turn a street carburetor into a high-performance carb: get that extra performance out of your ride in less than 30 minutes! Add up to 25-50 HP with PROFORM's 100% NEW, high-performance...

Direct Replacement Components to turn a street carburetor into a high-performance carb: get that extra performance out of your ride in less than 30 minutes! Add up to 25-50 HP with PROFORMs 100% NEW, high-performance...

Upgrade your Double Pumper with race-ready billet metering blocks! Primary block retains the original vacuum provisions. Secondary block has no power valve provision to fit the latest generation of carburetors. Kit includes...

Lokar Duo-Pak throttle cable set will easily adapt to most gas pedals and throttle assemblies. Cable comes equipped with aluminum fittings and aluminum ferrules to eliminate fraying and feature a "U-Cut-to-Fit" outer housing...