1974 Plymouth Duster Parts - Differential Hardware

Yukon master overhaul kit for Chrysler 8.75" rear ends. Included in this kit are Timken carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, oil...

This cast iron yoke is manufactured specifically for Mopar differentials. Includes the yoke, and mounting hardware. Important: Use MM3311 s trap kit, Note: Uses 7260 series U-joint (sold separately) that have a 2.125"...

If you are using your stock leaf spring rear suspension and you have added horsepower to your engine; then you need to add an adjustable pinion snubber. This helps control axle windup by adjusting the height to the floor pan....

These u-joint strap kits are designed for use on stock and Yukon pinion yokes with 7260 u-joint size. Includes: two straps and four bolts. Made in the USA.

Mopar 8-3/4" "89" case housing

This locking pawl and flanged nut is used on the right side axle of 8-3/4" differentials. The pawl secures the axle end play adjusting nut once proper bearing play is established.

Yukon master overhaul kit for Chrysler 8.75" rear ends. Included in this kit are Timken carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, oil...

This billet steel yoke is manufactured specifically for Mopar differentials. Includes the yoke, and mounting hardware. Important: Use MM3307 u-bolt kit, Note: Uses 1350 series U-joint (sold separately) that have a...

This billet steel yoke is manufactured specifically for Mopar differentials. Includes the yoke, and mounting hardware. Important: Use MM3307 u-bolt kit, Note: Uses 1350 series U-joint (sold separately) that have a...

This forged steel yoke is manufactured specifically for Mopar differentials. Includes the yoke, and mounting hardware. Important: Use MM3310 strap kit, Note: Uses 1350 series U-joint (sold separately) that have a...

Enhance the appearance of your rear end with ARP's stainless steel rear cover bolts. These bolts add a lustrous contrast to a painted OEM cover, compliment a chrome plated aftermarket version or add flash to that cast...

Replacement thrust spacer set for 8-3/4" differentials with clutch type Sure-Grip prior to 1970. Required to provide axle thrust surface in four-spider differential applications. One set required per vehicle.

These u-joint u-bolt kits are designed for use on stock and Yukon pinion yokes with 1310 u-joint size. Includes: two u-bolts (3/8" X 1-11/16") and four nuts. Made in the USA.

These u-joint u-bolt kits are designed for use on stock and Yukon pinion yokes with 7260 and 7290 u-joint size. Includes: two u-bolts (5/16" X 1-9/16") and four nuts. Made in the USA. One kit required per vehicle. NOTE:...

These u-joint strap kits are designed for use on stock and Yukon pinion yokes with 1350 u-joint size. Includes: two straps and four bolts. Made in the USA.

These u-joint u-bolt kits are designed for use on stock and Yukon pinion yokes with 1350 u-joint size. Includes: two u-bolts and four nuts. Made in the USA.

These u-joint strap kits are designed for use on stock and Yukon pinion yokes with 1310 u-joint size. Includes: two straps and four bolts. Made in the USA.

Replacement crush sleeve for setting up your rear axle. Crush sleeves cannot be reused if you are changing a ring and pinion or the front seal. Includes pinion nut washer and pinion flange nut. These are for the 9-1/4"...

This cast iron reproduction yoke is manufactured specifically for Dana 60 rear axles. Includes the yoke, retaining u-bolt, and mounting hardware. Note: Uses 1330 series U-joints (sold separately) that have a 3.625 " snap...

This forged steel reproduction yoke is manufactured specifically for Dana 60 rear axles. Includes the yoke, retaining u-bolt and mounting hardware. Note: Uses 1350 series U-joint (sold separately) that have a 3.62 5" snap...

This chrome moly billet yoke is manufactured specifically for Mopar differentials. Includes the yoke, u-bolt, and mounting hardware. Note: Uses 7260 series U-joint (sold separately) that have a 2.125" snap ring sp an with...

This cast iron reproduction yoke is manufactured specifically for Dana 60 rear axles. Includes the yoke, strap, and mounting hardware. Note: Uses 1310 series U-joints (sold separately) that have a 3.219" snap ring span...

This cast iron reproduction yoke is manufactured specifically for Dana 60 rear axles. Includes the yoke, retaining strap and mounting hardware. Note: Uses 1350 series U-joint (sold separately) that have a 3.625" s nap ring...

This set is for use on Dana 60, or any other rear end using 3/8"-16 x 3/4" bolts. Includes 12 chrome finished bolts and 12 Flat washers (not chromed).

Reproduction rear and housing e-brake, and brake line clip set for all 1960-76 models. Replace your rusted originals with these correct replacements. Must be welded to the factory locations.

This billet steel reproduction yoke is manufactured specifically for Dana 60 rear axles. Includes the yoke, retaining strap and mounting hardware. Note: Uses 1350 series U-joint (sold separately) that have a 3 .625" snap...

This chrome moly billet reproduction yoke is manufactured specifically for Mopar differentials. Includes the yoke, u-bolt, and mounting hardware. Note: Uses 7290 series U-joints (sold separately) that have a 2.62 5" snap...

This cast iron reproduction yoke is manufactured specifically for Dana 60 rear axles. Includes the yoke, strap, and mounting hardware. Note: Uses 7290 series U-joints (sold separately) that have a 2.625" snap ring span...

This cast iron reproduction yoke is manufactured specifically for Dana 60 rear axles. Includes the yoke, u-bolt, and mounting hardware. Note: Uses 1310 series U-joints (sold separately) that have a 3.219" snap rin g span...

This cast iron reproduction yoke is manufactured specifically for Dana 60 rear axles. Includes the yoke, retaining strap and mounting hardware. Note: Uses 1350 series U-joint (sold separately) that have a 3.625" s nap ring...

FilterMag powerful rare-earth magnet traps and holds wear inducing metal particles smaller than 40-microns down to 1-micron. The super-strong magnetic force holds FilterMag to the cover, is reusable and will reduce...

Ring gear bolts for Mopar 8-1/4" and 8-3/4" differentials. These are factory replacement quality. Sold as a set of 12.

Ring gear bolt for Mopar 8-1/4" and 8-3/4" differentials. This is factory replacement quality. Sold individually.

Work on your differential third member safely and easily with this lightweight fixture. It can be clamped or bolted to your work bench or simply mounted in a vise, and it fits neatly in your tool chest when the job is...

These Pro-Series ring gear bolt kits from ARP are forged from premium-grade 8740 chromoly steel and heat-treated to a rating of 190,000 psi. This is a set of 12 3/8"-24 LH threaded bolts for the 8-3/4" ring gear. Made...

Chrome differential cover bolts for 8-1/4" rear axles. Each set includes enough bolts to mount the differential cover to the axle housing.s

Chrome differential cover bolts for Dana 60 rear axles. Each set includes enough bolts to mount the differential cover to the axle housing.

Ring gear bolts for Mopar 8-1/4" and 8-3/4" differentials. These are genuinely direct from Mopar Performance. Sold as a set of 12.

OER® reproduction of the ventilator used by GM on a multitude of applications from the 1950s thru todays cars and trucks including the rear axle housing, automatic transmissions. front transfer case on 4 x 4 models and...

Did you know the rear axle housing was shipped to the assembly plant without the brake lines and fittings in place? A special piece of tape covered the vent hole to keep debris & moisture out during shipping. The plant then...

Did you know the rear axle housing was shipped to the assembly plant without the brake lines and fittings in place? A special piece of tape covered the vent hole to keep debris & moisture out during shipping. The plant then...