Product#: 3415

Bumper Bolt with Hex Nut; Stainless Steel Capped Head ; 3/8-16" x 1"; Zinc Plated

Reproduction GM bumper bolt for a variety of General Motors and Chrysler applications. Each zinc-plated steel carriage bolt features a polished stainless steel cap for superb cosmetic appearance, corrosion resistance and long...

Product#: 2710

Chrome Trim Screw, #8 x 3/4", With #8 Phillips Oval Head

Replacement chrome plated trim screws used on various GM vehicles. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is original...

Product#: 3822

Bumper Bolt with Hex Nut; Stainless Steel Capped Head ; 3/8-16 x 1-1/2; Zinc Plated

Reproduction bumper bolt for a variety of General Motors applications. Each zinc-plated steel carriage bolt features a polished stainless steel cap for superb cosmetic appearance, corrosion resistance and long life. Each bolt...

Product#: 8610

Flat Washer; 1/2" USS; Zinc Plated

1/2" USS zinc plated Flat Washer for a variety of applications. A washer is a thin plate (typically disk-shaped) with a hole (typically in the middle) that is normally used to distribute the load of a threaded fastener, such...

Product#: DW859T

1976-89 Mopar F/M-Body; Windshield; Light Green Tint; With Blue/Green Shade

OER reproduction windshield glass for various 1976-89 Mopar F-Body and M-Body models. Replacing your original damaged or missing windshield glass will enhance your vehicle?s appearance and safety by allowing you to see...

Product#: 10362

Bolt, 5/16-18 x 13/16" Pointed Tip With Hex Washer Head, Black Phosphate

OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. Note: For a money saving set of 10...

Product#: 3899508

1959-80 Trico Windshield Wiper Blade; 15" Length; Various Models; Each

Reproduction 15 inch "TRICO Style # PR-15-2W" wiper blade for a wide variety of classic vehicle models. Each blade features stainless steel construction and is loaded with a period-correct TRICO RF-15 style insert with a...

Product#: K51020

1962-76 GM, Dodge, Plymouth; Convertible Top Boot Storage Bag; Various Models

Why leave your top boot in the trunk exposed when you can keep it safe and clean by safely storing it in this special top boot storage bag. The storage bag will help protect your vehicles top boot while being stored in the...

Product#: 11503957

U-Nut; M6 - 1.0; Panel Range .030" to .160"; Center of Hole to Edge: 17/32"; Black Phosphate; Each

Black phosphate metric u-nut or foldover nut, that measures M6-1.0 to install and secure various components. Fits panel thickness from .80mm to 4 mm. (.030" to .160") Specifications: OE #: 11503957 Quantity: Individual...

Product#: MP40101

1965-74 Chrysler, Dodge, Plymouth; Windshield Washer Pump; Replacement

Replacement style windshield washer pump assembly designed for use with the applications listed below. The windshield washer pump circulates water from the windshield washer jar to the washer nozzles. This is a replacement...

Product#: *C15315

U-Nut Set; M6 - 1.0; Panel Range .030" to .160"; Black Phosphate; 25 Piece Set

Black phosphate metric u-nut or foldover nut, that measures M6-1.0 to install and secure various components. Fits panel thickness from .80mm to 4 mm. (.030" to .160"). Set of 25 u-nuts. Specifications: OE #: 11503957 ...

Product#: A5713K

5/16" X 18 X 1-1/4" Hex Washer Head Spin Lock Bolt; Phospate Coating; Set of 24

Reproduction 5/16" x 18 x 1-1/4" hex washer head spin lock bolt finished iin a black phospate coating for an authentic original appearance and corrosion resistance. Set of 24. Use as required. Product Specifications: ...

Product#: *R1383

Hood Insulation Fastener; 5/16" Stem Diameter; 3/4" Stem Length; 1-3/4" Head Diameter; 20-Pieces

Replacement black nylon 1-3/4" hood insulation retainer is just what your GM vehicle needs to keep your original hood insulation where it belongs... attached to the hood. This retainer is a service replacement for most...

Product#: 11500367

1965-2002 GM; Door Lock Striker Washer; 3.50MM Thick; Each

Correct reproduction of the original threaded striker washer for use on 1965-2002 Buick, Chevrolet, Pontiac, and Oldsmobile models as listed. The door lock striker washer is installed on the door jamb for either the right or...

Product#: 20540336

Weatherstrip Retainer, Plastic, Various GM and Ford Models

OER reproduction retaining pin used by GM for various applications. Manufactured from injection molded plastic as original, this retaining pin measures M4.2 x 1.41 x 15 and fits a 4.75MM dia. hole. Sold individually. Use as...

Product#: LF122175A

1975 Plymouth License Plate Frame - Black and Chrome with White Lettering

Flaunt your Mopar pride with this OER® custom license plate frame that shows off your vehicle year and model. Produced in die-cast zinc with an elegant, rust-preventive triple chrome plating with top mounting holes. ...

Product#: LF122176A

1976 Plymouth License Plate Frame - Black and Chrome with White Lettering

Flaunt your Mopar pride with this OER® custom license plate frame that shows off your vehicle year and model. Produced in die-cast zinc with an elegant, rust-preventive triple chrome plating with top mounting holes. ...

Product#: LF122175B

1975 Plymouth License Plate Frame - Blue and Chrome with White Lettering

Flaunt your Mopar pride with this OER® custom license plate frame that shows off your vehicle year and model. Produced in die-cast zinc with an elegant, rust-preventive triple chrome plating with top mounting holes. ...

Product#: LF122176B

1976 Plymouth License Plate Frame - Blue and Chrome with White Lettering

Flaunt your Mopar pride with this OER® custom license plate frame that shows off your vehicle year and model. Produced in die-cast zinc with an elegant, rust-preventive triple chrome plating with top mounting holes. ...

Product#: LF121075A

1975 Mopar License Plate Frame - Black and Chrome with White Lettering

Flaunt your Mopar pride with this OER® custom license plate frame that shows off your vehicle year and model. Produced in die-cast zinc with an elegant, rust-preventive triple chrome plating with top mounting holes. ...