Auto Rotisserie EZ Spin; with Jacks
The Auto Rotisserie E-Z Spin features 12 multi-angle postioning stops every 30 degrees, HD swivel casters and rotates a full 360 degrees. It's work height is adjustable from 44" to 59", center line is adjustable from 10" to...
Blair Tools; Holcutter Set; 1/8" D.O.C.
Holcutters are not hole saws. They are precision ground, heat treated tools that easily cut through the stock rather than ripping, tearing, and pushing thru as do typical hole saws. They can produce holes 3 times faster and...
Glass Molding Clip Installation Tool
This handy tool makes a difficult job much easier. This tool removes or installs the clips found on most exterior moldings and helps to avoid damage to the moldings or the surface that they are mounted to.
The auto hood puller is designed for easy pulling and mounting of the hood. Helps to eliminate scratches and dings to the paint on the hood and fenders. To be used with any engine pulling hoist.
Great tool to have when replacing your OEM or aftermarket steering wheel. Allows for easy removal, can be used for almost any model and includes instructions.
Windshield Molding / Door Handle Clip Remover
Specialty pliers for removing door handle clips and chrome molding on most windshields and rear glass. Jaws slip under door handle without damage to panel material, and offset handle permits easy access to molding clips.
Blair Tools; Rotabroach 8mm-20Mm Metric Cutter Set; 1/4" Depth of Cut
For precision hole making in sheet metal and frame materials up to 1/4" thick, Rotabroach® annular cutters make clean, burr-free, round holes with no deforming of stock or damage to the surrounding material. Ideal for...
Blair Tools; Rotabroach 8mm-20Mm Metric Cutter Set; 1/4" Depth of Cut
Classic $87.99 set
Body Shims 1/16" Thick, 1-1/4" x 1-1/8" with 3/8" Bolt Slot. Zinc Plated, 50 Piece Set
When replacing sheet metal one of the most essential items are shims. Shims are important when it comes to aligning front end sheet metal. Please check your originals to be sure your ordering the correct shims necessary for...
Body Shims 1/16" Thick, 1-1/4" x 1-1/8" with 3/8" Bolt Slot. Zinc Plated, 50 Piece Set
Classic $17.99 set
Body Shims 1/8" Thick, 1-1/4" x 1-1/8" With 3/8" Bolt Slot. Zinc Plated, 50 Piece Set
When replacing sheet metal one of the most essential items are shims. Shims are important when it comes to aligning front end sheet metal. Please check your originals to be sure your ordering the correct shims necessary for...
Body Shims 1/8" Thick, 1-1/4" x 1-1/8" With 3/8" Bolt Slot. Zinc Plated, 50 Piece Set
Classic $22.99 set
Blair Tools; 3/8" Spotweld Cutter Set; With Skip Proof Pilot
When you have a lot of spotwelds to remove, step up to the premium spotweld cutters for longer life in today's high-strength body steels. These cutters have a heavier wall (.090") for extreme durability and two step geometry...
Blair Tools; Antenna/Access Holcutter™ Set
Holcutter™ is not a hole saw. It's a precision ground, heat treated tool that easily cuts through the stock rather than ripping, tearing and pushing through as do typical hole saws. The Holecutter™ can produce...
Universal Molding Release Tool
Slide tool left or right under the molding until it hooks a retaining clip, then just rock the tool with a twist of the wrist to release the clip. Heat treated, high-carbon steel.
The ultimate solution for removing door pins fast. Drives out even stubborn hinge pins. Works on all GM cars with removable hinge pins. Includes pin puller to remove loosened pins.
Super Seam Buster (For Air Hammers)
This heavy-duty chisel allows you to easily separate spot welded or bonded panels. Save up to 15 minutes per panel replacement. Great for quarter panels, rocker panels and other pinch welded areas. Sharpened on two edges, the...
Blair Tools; Paintless Dent Removal Access Hole Set
This Rotabroach® set is for cutting access holes, fabrication, removing spot welds and body work. Rotabroach® Cutters are for precision hole making in sheet metal, frame materials, and plate stock up to 1/2" thick,...
Blair Tools; Rustproofer Cutter Set; With Skip Proof Pilot
This Rotabroach® set is for rustproofing and cutting access holes. Rotabroach® Cutters are for precision holemaking in sheet metal, frame materials, and plate stock up to 1/2" thick, whether Mild Steel, Stainless...
Blair Tools; Rustproofer Cutter Set; With Standard Pilot
This Rotabroach® set is for rustproofing and cutting access holes. Rotabroach® Cutters are for precision hole making in sheet metal, frame materials, and plate stock up to 1/2" thick, whether Mild Steel, Stainless...
Blair Tools; Blair Holcutter™ 2-3/4" Cutter With 1/8" Depth Of Cut
Holcutter™ is not hole saw. It is precision ground, heat treated tool that easily cuts through the stock rather than ripping, tearing, and pushing thru as do typical hole saws. The Holecutter™ can produce holes 3...