1975 Chevrolet All Models Parts - Performance Ignition

This performance ignition module is a direct replacement for GM computer controlled distributors. This module provides enhanced high RPM performance and increase spark plug voltage. Engineered with low saturation for maximum...

OEM ignition coil for LS3 V8. 8 required per vehicle.

OEM ignition coil for LS1 V8. 8 required per vehicle.

The Street Fire Capacative Discharge ignition is perfect for performance enthusiasts with a tight budget. Capacative discharge will fire a series of multiple sparks that last for 20 degrees of crankshaft rotation when the...

Upgrade/replacement Ignitor III module for 8 cylinder automotive Pertronix billet distributors. These distributor modules are direct bolt-in replacements for your Pertronix Flame Thrower III distributor. Installed easily and...

Replacement Unilite ignition module for Mallory breakerless distributors. Fits all series Mallory Unilite distributors except 42, 50 & 57. Requires a 1.4 ohms Ballast resistor, Loom resistor or internally resisted coil. ...

Replacement hi-voltage 60,000 volt chrome ignition coil is just what you’ll need to keep your breaker-point ignition system operating efficiently and looking good. Includes 1.4ohm resistor.

The 6LS-2 Ignition Controller allows you to map a timing advance curve, as well as program a two-step rev limiter, a vacuum advance curve, and even a step retard in case you want to add nitrous to the mix. The 6LS-2 is...

Replacement coil cover for MSD # 8362 Street Fire Distributor or stock GM HEI distributor. {fitment}

When running an MSD Atomic EFI or similar throttle body fuel injection system with a 6EFI ignition box, the 6EFI ignition coil is made for you. Designed to match the 6EFI ignition, the 6EFI coil has a clean black appearance...

Don't let the compact size of the Blaster SS Coil fool you because it is packed with performance. The efficient E-core windings are designed to produce high amounts of current without sacrificing the voltage output. In fact,...

MSD's new Digital 6A is the base model of the capacitive discharge multiple spark 6 Series design. Like all of the MSD 6 Series Ignitions, the 6A will work with virtually any vehicle as long as it has a 12-18 volt...

If you are looking to upgrade your stock coil or want to complement the performance of your MSD 5, 6 and 7 Series Ignition, the Blaster Coil is the right choice. The Blaster 2 Coil shares the same special windings and high...

If your vehicle is equipped with a V8 engine with a GM factory distributor, upgrade to Accel components during your next tune-up. You'll enjoy increased performance, longer life and maximum dependability. {specs} {fitment}

This performance ignition module is a direct replacement for GM computer controlled distributors. This module provides enhanced high RPM performance and increase spark plug voltage when used with a corresponding Flame Thrower...

If your vehicle is equipped with a GM factory HEI distributor, upgrade to Mallory control module during your next tune-up. You'll enjoy increased performance, longer life and maximum dependability. {specs} {fitment}

If you are looking to upgrade your stock coil or want to complement the performance of your MSD 5, 6 and 7 Series Ignition, our Blaster Coils are the right choice. The Blaster 3 Coil shares the same special windings and high...

Replacement distributor cap for stock breaker point GM V8 distributors or MSD Pro-Billet Distributors # 8394 with female terminal. Made in USA

Complete your ignition upgrade with a Flame Thrower high performance ignition coil! The Flame Thrower coil fits into your existing coil bracket for a clean, factory look. Enables larger plug gaps for greater fuel efficiency...

Complete your ignition upgrade with a Flame Thrower high performance ignition coil! The Flame Thrower coil fits into your existing coil bracket for a clean, factory look. Enables larger plug gaps for greater fuel efficiency...

Complete your ignition upgrade with a Flame Thrower high performance ignition coil! The Flame Thrower coil fits into your existing coil bracket for a clean, factory look. Enables larger plug gaps for greater fuel efficiency...

Ignition points for all 23, 24, 25 26 and 27 series Mallory breaker point distributors. {specs} {fitment}

Taylor Thunder Volt 8.2mm Chevrolet small block "Under Headers" Custom Race Fit ignition wires are dyno tested and proven to increase horsepower and torque. Designed with a Ferrite spiral-wound core coated with a blend of...

Taylor Thunder Volt 8.2mm Chevrolet small block "Under Headers" Custom Race Fit ignition wires are dyno tested and proven to increase horsepower and torque. Designed with a Ferrite spiral-wound core coated with a blend of...

Taylor 409 Pro Race 10.4mm high performance ignition wires are designed for street and track performance. Featuring tightly woven heat treated fiberglass braid over a 100% silicone Spiro-Pro ignition wire providing a 3-layer...

Taylor Thunder Volt 8.2mm Chevrolet small block "Under Headers" Custom Race Fit ignition wires are dyno tested and proven to increase horsepower and torque. Designed with a Ferrite spiral-wound core coated with a blend of...

Taylor 409 Pro Race 10.4mm high performance ignition wires are designed for street and track performance. Featuring tightly woven heat treated fiberglass braid over a 100% silicone Spiro-Pro ignition wire providing a 3-layer...

Taylor 409 Pro Race 10.4mm high performance ignition wires are designed for street and track performance. Featuring tightly woven heat treated fiberglass braid over a 100% silicone Spiro-Pro ignition wire providing a 3-layer...

Taylor Thunder Volt 8.2mm ignition wires are dyno tested and proven to increase horsepower and torque. Designed with a Ferrite spiral-wound core coated with a blend of copper/nickle bonded with a conductive acrylic cover for...

Taylor Thunder Volt 8.2mm ignition wires are dyno tested and proven to increase horsepower and torque. Designed with a Ferrite spiral-wound core coated with a blend of copper/nickle bonded with a conductive acrylic cover for...

Taylor Thunder Volt 8.2mm Chevrolet small block "Over Valve Covers" Custom Race Fit ignition wires are dyno tested and proven to increase horsepower and torque. Designed with a Ferrite spiral-wound core coated with a blend...

Taylor Thunder Volt 8.2mm Chevrolet small block "Over Valve Covers" Custom Race Fit ignition wires are dyno tested and proven to increase horsepower and torque. Designed with a Ferrite spiral-wound core coated with a blend...

Taylor Thunder Volt 8.2mm Chevrolet small block "Over Valve Covers" Custom Race Fit ignition wires are dyno tested and proven to increase horsepower and torque. Designed with a Ferrite spiral-wound core coated with a blend...

Taylor Thunder Volt 8.2mm Chevrolet small block "Over Valve Covers" Custom Race Fit ignition wires are dyno tested and proven to increase horsepower and torque. Designed with a Ferrite spiral-wound core coated with a blend...

Taylor Thunder Volt 8.2mm Chevrolet small block "Under Headers" Custom Race Fit ignition wires are dyno tested and proven to increase horsepower and torque. Designed with a Ferrite spiral-wound core coated with a blend of...

Taylor Thunder Volt 8.2mm ignition wires are dyno tested and proven to increase horsepower and torque. Designed with a Ferrite spiral-wound core coated with a blend of copper/nickle bonded with a conductive acrylic cover for...

Taylor Thunder Volt 8.2mm ignition wires are dyno tested and proven to increase horsepower and torque. Designed with a Ferrite spiral-wound core coated with a blend of copper/nickle bonded with a conductive acrylic cover for...

Taylor Thunder Volt 8.2mm ignition wires are dyno tested and proven to increase horsepower and torque. Designed with a Ferrite spiral-wound core coated with a blend of copper/nickle bonded with a conductive acrylic cover for...

Taylor Thunder Volt 8.2mm Chevrolet small block "Under Headers" Custom Race Fit ignition wires are dyno tested and proven to increase horsepower and torque. Designed with a Ferrite spiral-wound core coated with a blend of...

Taylor Thunder Volt 8.2mm Chevrolet Big Block "Over Valve Covers" Custom Race Fit ignition wires are dyno tested and proven to increase horsepower and torque. Designed with a Ferrite spiral-wound core coated with a blend of...

Taylor Thunder Volt 8.2mm Chevrolet Big Block "Over Valve Covers" Custom Race Fit ignition wires are dyno tested and proven to increase horsepower and torque. Designed with a Ferrite spiral-wound core coated with a blend of...

Taylor Thunder Volt 8.2mm Chevrolet Big Block "Over Valve Covers" Custom Race Fit ignition wires are dyno tested and proven to increase horsepower and torque. Designed with a Ferrite spiral-wound core coated with a blend of...

Taylor Thunder Volt 8.2mm Chevrolet small block "Over Valve Covers" Custom Race Fit ignition wires are dyno tested and proven to increase horsepower and torque. Designed with a Ferrite spiral-wound core coated with a blend...

Taylor Thunder Volt 8.2mm Chevrolet small block "Over Valve Covers" Custom Race Fit ignition wires are dyno tested and proven to increase horsepower and torque. Designed with a Ferrite spiral-wound core coated with a blend...

Taylor Thunder Volt 8.2mm Chevrolet big block "Over Valve Covers" Custom Race Fit ignition wires are dyno tested and proven to increase horsepower and torque. Designed with a Ferrite spiral-wound core coated with a blend of...

Taylor Thunder Volt 8.2mm Chevrolet big block "Under Headers" Custom Race Fit ignition wires are dyno tested and proven to increase horsepower and torque. Designed with a Ferrite spiral-wound core coated with a blend of...

Taylor Thunder Volt 8.2mm Chevrolet big block "Under Headers" Custom Race Fit ignition wires are dyno tested and proven to increase horsepower and torque. Designed with a Ferrite spiral-wound core coated with a blend of...

Taylor Thunder Volt 8.2mm Chevrolet big block "Under Headers" Custom Race Fit ignition wires are dyno tested and proven to increase horsepower and torque. Designed with a Ferrite spiral-wound core coated with a blend of...

This distributor features a flawless lightweight CNC-machined 6061-T-6 billet aluminum housing and a polished steel shaft with a QPQ coating. This process produces a durable finish that reduces friction and resists corrosion....

Upgrade/replacement Flame Thrower III module for 8 cylinder automotive Pertronix billet distributors. These distributor modules are direct bolt-in replacements for your Pertronix Flame Thrower III distributor. Installed...

Fits 55 - 82 Chevy small block and big block engines. NO rebuilt components: 100% NEW! It has a high-performance control module, a hardened gear, a capacitor that prevents radio static, a high-dielectric cap with brass...

The ACCEL SuperBox Capacitive Discharge Ignition System is one of the best ignition values on the market, a perfect blend of value and performance. When the engine is running at low rpm, this modern capacitive-discharge...