1978 GMC Jimmy Parts - Steering

Reproduction power steering pump bracket which is required when mounting the power steering pump on Big Block applications.

This is an all new gear box manufactured with brand new tooling. Replaces gear box with casting number of 5698180 and was used in many GM 2wd pickups from 1967-86. Can also replace Dodge 3496910, but alignment flat may not...

If you’re in the market to replace the worn out, damaged or missing power steering pump, choose this OER® Authorized remanufactured power steering pump that is thoroughly remanufactured, carefully inspected and restored...

1975-86 C10 Pickup; Pitman Arm; Power Steering

Reproduction of the original steering column coupler components commonly known as the rag joint. These special components can be a weak link between the steering column and the steering gear box. Each set includes the correct...

Convenient set of hardware for steering shaft couplers on many GM vehicles. Set includes the (1) 3/8"-24 hex nut and lock washer and (1) 5/16"-24 nut and lock washer. Also includes the 12-point coupler bolt that secures the...

If you’re in the market to replace the worn out, damaged or missing power steering pump, choose this OER® Authorized remanufactured power steering pump that is thoroughly remanufactured, carefully inspected and restored...

Quality reproduction of the original pitman arm designed for 1973-91 Chevrolet and GMC models with power steering. Manufactured to exact factory specifications. Each assembly features heat treated components and forging, and...

This is the O-ring set for Saginaw power steering pumps. Includes 8 pieces to re-seal the pump to the reservoir. Does not include the shaft seal. Fits most Saginaw pumps through 1977 including Saginaw P series. Chevrolet...

Reproduction of the original pitman arm designed for use with various 1969-89 Chevrolet and GMC trucks. Each pitman arm is manufactured in heavy duty cast iron replicating the original in design, appearance and fitment. Is...

Reproduction of the power steering pump cap designed for use with a variry of 1962-2005 GM, and Chrysler, Dodge, Plymouth models that included a Saginaw power steering pump. Each cap is manufactured in quality injection...

If you’re in the market to replace the worn out, damaged or missing power steering pump, choose this OER® Authorized remanufactured power steering pump that is thoroughly remanufactured, carefully inspected and restored...

This 11 piece set includes the o-rings, gaskets, seals, hardware and washers you will need to install a reservoir on your saginaw power steering pump. This set has chrome hardware that are designed to be used with a chrome...

If you're looking for a power steering pump for your classic vehicle and are finding that your part has become obsolete and cores for reman units are unavailable, you can now replace that obsolete pump with a brand-new...

If you're looking for a replacement power steering pump, now you can replace it with a brand-new OER® Authorized pump that has been thoroughly tested, and manufactured to meet the highest OEM standards of quality. This...

If you’re in the market to replace the worn out or damaged power steering pump, choose our replacement style power steering pump. Each power steering pump is thoroughly remanufactured and carefully inspected to provide years...

Reproduction of the original power steering brackets designed for use with various 1969-72 Chevrolet models with small block and long water pump. . Each bracket is manufactured in quality stamped steel replicating the...

This 11 piece set includes the o-rings, gaskets, seals, hardware and washers you will need to install a reservoir on your saginaw power steering pump. This set has unfinished hardware that are designed to be used with a...

Replace a non working or worn out gear box with this quality remanufactured power steering gear box. Each gear box is completely tested for reliability and quality before leaving the factory, has a 1 year limited warranty and...

This is the hose adapter fitting for Saginaw power steering gear box or pump. Straight, inverted flare zinc coated steel, 5/8"-18 to -6AN. Fits most Saginaw gear boxes or pumps 1960 through 1977 including Saginaw P series. ...

Rebuilt power steering gear box for a variety of truck applications. Each gear box is completely tested for reliability and quality before leaving the factory. Replaces competitor #'s 27-7512, CP7512 7512, 1248, 36G0059. ...

This is the stud and bolt kit for Saginaw power steering pumps. Includes (2) studs (3/8"-16 thread), (1) bolt 3/8"-16 thread). Fits most Saginaw pumps through 1977 including Saginaw P series. This set is the chrome plated set...

Replace a non working or worn out gear box with this quality remanufactured power steering gear box. Each gear box is completely tested for reliability and quality before leaving the factory, has a 1 year limited warranty...

This is the stud and bolt kit for Saginaw power steering pumps. Includes (2) studs (3/8"-16 thread), (1) bolt 3/8"-16 thread). Fits most Saginaw pumps through 1977 including Saginaw P series. This set is black phosphate...

1966-75 F100; Tie Rod End Adjusting Sleeve; 4 X 4

Replace your worn out original wheel bearings to maintain proper alignment and smooth rolling. Always check the bearings whenever removing the brake drum or rotor. 2 required per vehicle. Applications: 1962-70 C10 With...

1971-86 C10 Pickup; Ball Joint; Front; Lower

1973-86 C10 Pickup; Ball Joint; Front; Upper

1973-86 C10 Pickup; Control Arm Bushing; Front; Lower

1973-87 C10 Pickup; Control Arm Bushing; Lower

1973-86 C10 Pick up; Control Arm Bushing; Front; Upper

Reproduction of the original tie-rod end designed for use with various 2-wheel drive Chevrolet and GMC truck models. Restores vehicle handling, and OE alignment. Reduces tire wear, and improves steering response. Each tie-rod...

Reproduction of the original outer tie-rod end for 1976-86 Chevrolet and GMC K-Series 4WD truck models and 1987-91 V-Series 4WD models. Each outer tie rod end is manufactured to factory specifications that meet or exceed...

1975-86 C10 Pickup; Tie Rod End; Outer; LH/RH

1976-86 Chevy K10; Tie Rod End; Right; Outer

1975-86 C10 Pick Up; Tie Rod End; Inner; LH/RH

Reproduction of the original outer tie-rod end designed for use with various 1976-91 Chevrolet and GMC truck models. Each tie rod end is manufactured to meet or exceed factory specifications for a ease of installation and...

Reproduction of the original outer tie-rod end designed for use with various 1971-97 Chevrolet and GMC truck models with 2-wheel drive. Restores vehicle handling, and OE alignment. Reduces tire wear, and improves steering...

1976-80 K10; K20; K5 Blazer, Tie Rod End, Front Left Outer

1975-82 C10, C20, C30 Pickup; Idler Arm

1973-74 and 1987-91 Blazer and K10; Stabilizer Bar Bushing; Front; Eye Bushing

Each OER® Authorized reproduction rear drag link end is manufactured to meet or exceed factory specifications for a ease of installation and years of trouble-free service. Measures 1" in diameter and 8.33" in length. ...

Repair torn and worn-out tie rod end boots - without having to buy the entire tie rod. Add durability surpassing most OEM rubber boots. Made of high performance polyurethane for added performance and durability. Tie rod...

1975-86 K10 and Blazer; Tie Rod End; Inner; LH/RH

1975-86 K10 and Blazer; Tie Rod End; Outer; LH/RH

1969-74 Blazer; Tie Rod End Adjusting Sleeve

Repair torn and worn-out tie rod end boots - without having to buy the entire tie rod. Add durability surpassing most OEM rubber boots. Made of high performance polyurethane for added performance and durability. Tie rod...

Each OER® Authorized reproduction front drag link end is manufactured to meet or exceed factory specifications for a ease of installation and years of trouble-free service. Measures 1" in diameter and 6.33" in length. ...

Reproduction of the original style tie-rod adjusting sleeve designed for use with various 1957-2005 General Motors and AMC model vehicles. Each adjusting sleeve is manufactured to factory specifications replicating the...

1973-77 Regal; Tie Rod End Adjusting Sleeve

Power Steering Serpentine Pulley

Our Power Steering Conversion Hose kit is designed to fit the GM Saginaw power steering pump with inverted flare pressure fitting. It fits POL Rack and Pinion and the GM 500, 605, 800 and 600 Series power steering gear box!...

In-line Magna-Pure Filter - Serviceable Magnetic filter element with patented built in bypass for optimal performance; filters up to 190 micron particles. Protects the entire steering system from contmination. Flushing the...

To complete your ididit steering column installation, you should also replace your rag joint. When installing an ididit column in your car, you must use the correct application to match the column output shaft. Made in USA

This coupler connects the intermediate shaft to the steering column on several GM models with a 1" 48 spline x 3/4" double D shape.