Product#: MG88355

Motive Gear Performance 3.55 Ring and Pinion Sets for Ford 8.8" Rear Ends

Motive Gear Performance ring and pinions for Ford rear ends. Extensive tested Motive Gear?s superior quality of components are the result of years of development, outstanding design, and state-of-the-art manufacturing...

Product#: MG88373

Motive Gear Performance 3.73 Ring and Pinion Sets for Ford 8.8" Rear Ends

Motive Gear Performance ring and pinions for Ford rear ends. Extensive tested Motive Gear?s superior quality of components are the result of years of development, outstanding design, and state-of-the-art manufacturing...

Product#: MG88331

Motive Gear Performance 3.31 Ring and Pinion Sets for Ford 8.8" Rear Ends

Motive Gear Performance ring and pinions for Ford rear ends. Extensive tested Motive Gear?s superior quality of components are the result of years of development, outstanding design, and state-of-the-art manufacturing...

Product#: 141697-BCHW

Chevy Bowtie Emblem Rear End Cover, Gm, 12 Bolt, Passenger Car

Reinforced lightweight aluminum rear end cover designed to strengthen the rear housing case in heavy torque situations. The familiar Bowtie Emblem is raised and precision milled on a black crinkle coated surface. Each cover...

Product#: 141696-BCHW

GM 8.2, 8.5 10 Bolt; Rear End Cover, Chevy Bowtie Emblem

Reinforced lightweight aluminum rear end cover designed to strengthen the rear housing case in heavy torque situations. The familiar Bowtie Emblem is raised and precision milled on a black crinkle coated surface. Each cover...

Product#: LW18000

Lakewood; Universal; Zinc Plated Drive Shaft Safety Loop

Required and approved by all major racing sanctioning bodies this universal driveshaft safety loop is fully adjustable to fit most vehicles. The four piece design is manufactured from 1/4" thick, 2" wide mild steel, bright...

Product#: M7126B

GM 12 Bolt Rear End Cover; Chevy 12-Bolt, Dana 60; Semi Gloss Black

Dress up your 12 Bolt or Dana rear end with our Semi-Gloss Black Powder Coated cover. Available for Chevy 12 Bolt car and Dana 60 rear ends.

Product#: 68082-BCHW

Chrysler Pinion Snubber, Adjustable, 8 3/4 Pin Type

Get better traction and prevent bottoming out with this adjustable pin pinion snubber for Chrysler 8-3/4 in. rear ends. When under heavy load (acceleration) the rear springs will compress, and the axle can rotate. A pinion...

Product#: A4500218

1968-11 Ford/Lincoln/Mercury; Rear Axle Shaft Seal

Centric OE replacement wheel seals retain lubricant, keep contaminants out, and protect wheel bearings from premature wear. Manufactured and inspected to factory standards for direct fit. Sold individually. Click Here For...

Product#: MG88390

Motive Gear Performance 3.90 Ring and Pinion Sets for Ford 8.8" Rear Ends

Motive Gear Performance ring and pinions for Ford rear ends. Extensive tested Motive Gear?s superior quality of components are the result of years of development, outstanding design, and state-of-the-art manufacturing...

Product#: MG88410

Motive Gear Performance 4.10 Ring and Pinion Sets for Ford 8.8" Rear Ends

Motive Gear Performance ring and pinions for Ford rear ends. Extensive tested Motive Gear?s superior quality of components are the result of years of development, outstanding design, and state-of-the-art manufacturing...

Product#: 141695-BCHW

Chevy Bowtie Emblem Rear End Cover, 7.5 Gm, 10 Bolt

Reinforced lightweight aluminum rear end cover designed to strengthen the rear housing case in heavy torque situations. The familiar Bowtie Emblem is raised and precision milled on a black crinkle coated surface. Each cover...

Product#: MG8800

Motive Gear Master Bearing Kits w/ Timken Bearings for Ford 8.8" Rear Ends

Motive Gear Master Bearing Kits with Timken bearings for 8.8" Ford rear ends. These kits include Timken Bearings (Carrier, Front and Rear Pinion, Pilot where applicable), Brush, Cover Gasket (or RTV), Crush Sleeve (or...

Product#: 68083-BCHW

Chrysler Screw Type Pinion Snubber, Adjustable, 8 3/4 Screw-In Type

Get better traction and prevent bottoming out with this adjustable pin pinion snubber for Chrysler 8-3/4 in. rear ends. When under heavy load (acceleration) the rear springs will compress, and the axle can rotate. A pinion...

Product#: M7128B

Moser - Dana 60 Rear End Cover - Semi Gloss Black

Moser rear end cover for 12 bolt rear ends. Semi Gloss Black to make your rear end look amazing. Available for Chevy 12 Bolt car and Dana 60 rear ends. Dress up your 12 Bolt or Dana rear end with our Semi-Gloss Black Powder...

Product#: 8660S

1964-1996 Multi Purpose Seal

Oil and grease seal features precision sealing design to prevent lubricant escape and stop harmful contaminants from entering. Reinforced outer case helps prevent installation damage and enhances durability. Ribbed rubber...

Product#: 1236317

1971-2002 GM; Rear Axle Ventilator; Various Models; Reproduction; For .452 Hole

Reproduction of the original style rear axle ventilator designed for use with various 1971-2002 Buick, Cadillac, Chevrolet, Oldsmobile, and Pontiac models as listed. Each ventilator is manufactured in quality injection...

Product#: C229200

Competition Engineering Fabricated Ford 9" Rear Housing; Full Bodied Car; Mild Steel; 3" Axle Tubes; 60.75" Length

Competition Engineering Mild Steel Rear End. Fabricated Ford 9" rear axle housing triangulated design offers increased strength over three piece stock housings. CAD designed, CNC manufactured and offered in 4130 Chrome Moly...

Product#: 15771000

1953-2010 GM; Rear Axle/Transmission Ventilator; for 3/8" Hole

OER® reproduction of the ventilator used by GM on a multitude of applications from the 1950s thru todays cars and trucks including the rear axle housing, automatic transmissions. front transfer case on 4 x 4 models and...