1999 Chevrolet Camaro Parts - Steering

Replace your damaged or missing power steering reservoir cap with this quality aftermarket cap. This cap fits perfectly on original and reproduction power steering pump reservoirs.

Replace your damaged or missing power steering reservoir cap with this quality aftermarket cap. This cap fits perfectly on original and reproduction power steering pump reservoirs.

Reproduction of the 12-point, grade 8 bolt that secures the steering coupler to the steering shaft on most GM vehicles. The original couplers came with a 12-point bolt in the location where tightening this bolt squeezes the...

Our Power Steering Conversion Hose kit is designed to fit the GM Saginaw power steering pump with inverted flare pressure fitting. It also fits the GM 500, 605, 800 and 600 Series power steering gear box! These hose kits are...

Replace your damaged or missing power steering reservoir cap with this GM replacment cap. This cap fits perfectly on original and reproduction power steering pump reservoirs.

Original GM power steering pump cap designed for use with a variety of Buick, Chevrolet, Cadillac, Pontiac, and Oldsmobile models as listed. Replace your damaged or missing power steering reservoir cap with an original GM...

Power Steering Hose Applications: 1998-2002 Chevrolet Camaro - 5.7L V8 1998-2002 Pontiac Firebird - 5.7L V8

Power Steering Hose Applications: 1995-1999 Chevrolet Camaro - 3.8L V6 1995-1999 Pontiac Firebird - 3.8L V6

Original GM power steering pump pulleys for 1998-02 Firebird models. These stamped steel pulleys may be just what you need to get your power steering working at peak efficiency. Warning: Concerning Steering Pump Pulleys...

Power Steering Hose Applications: 1998-2002 Chevrolet Camaro - 5.7L V8 1998-2002 Pontiac Firebird - 5.7L V8

Power Steering Hose Applications: 1995-2002 Chevrolet Camaro - 3.8L V6 1995-2002 Pontiac Firebird - 3.8L V6

This billet aluminum power steering reservoir is designed for March Performance pulley sets that use GM type 2 power steering pumps. Includes cap, mounting bracket and mounting hardware. NOTE: Does not incl ude hoses or...

A leak in your power steering system can make a mess of your engine compartment, your driveway and garage floor. You can also burn up your power steering pump by driving your classic when it is low on fluid. Replace your...

BMR's custom width rack for the 4th gen is biased to the passenger side and the steering shaft is moved 1" to the drivers side for improved header clearance. Flaming River's billet bearing-style u-joints sized to the OE...

Customize your LS1 engine with a Type II power steering pump. This pump is designed as a direct bolt-in replacement for stock components, offering easy installation. 100% new components Made in USA

Customize your LS1 engine with a Type II power steering pump. This pump is designed as a direct bolt-in replacement for stock components, offering easy installation. 100% new components Made in USA

A leak in your power steering system can lead to a very serious and possibly dangerous situation. Leaking hoses can cause a loss of steering. Replace your worn out or cracked power steering return hose before big problems...

Customize your LS1 engine with a Type II power steering pump. This pump is designed as a direct bolt-in replacement for stock components, offering easy installation. 100% new components Made in USA

A leak in your power steering system can make a mess of your engine compartment, your driveway and garage floor. You can also burn up your power steering pump by driving your classic when it is low on fluid. Replace your...

BMR's custom width rack for the 4th gen is biased to the passenger side and the steering shaft is moved 1" to the drivers side for improved header clearance. Flaming River's billet bearing-style u-joints sized to the OE...

Original GM power steering pump pulley for use 1995-2002 Camaro and Firebird 6 cylinder 3.8 liter models. This stamped steel pulley may be just what you need to get your power steering working at peak efficiency. {fitment}

BMR's custom width rack for the 4th gen is biased to the passenger side and the steering shaft is moved 1" to the drivers side for improved header clearance. Flaming River's billet bearing-style u-joints sized to the OE...

If you?re in the market to replace the worn out, damaged or missing power steering pump, choose our replacement style power steering pump. Thoroughly remanufactured, this pump is carefully inspected and remanufactured to...

Old Air Power steering pump bracket for GM small block engines using Wide Mount brackets and a Saginaw power steering pump. Deigned for use with long water pumps.

Note: No further discounts apply.

This chrome plated self-locking nut is designed for aluminum performance power steering pulleys. It can also be used with OE and aftermarket pulleys on Saginaw power steering pumps with a 9/16"-18 threaded shaft. Made in USA

This braided stainless steel power steering hose set is designed for March Performance pulley sets that use GM type 2 power steering pumps with a remote reservoir. Includes three hoses that connect the pump and reservoir to...

This braided stainless steel power steering hose set is designed for March Performance pulley sets that use GM type 2 power steering pump with a remote reservoir. Includes three hoses that connect the pump and reservoir to...

Note: No further discounts apply.

Original GM tie rod end dust boot for 1993-02 models. Tie rod end dust boots should be replaced when changing the tie rods. (2 required per vehicle)

1988-04 Regal; Rack and Pinion Mount Bushing

OER Authorized reproduction of the original inner tie-rod end designed for use with various GM models. Restores vehicle handling, and OE alignment. Reduces tire wear, and improves steering response. Each tie-rod end includes:...

1993-02 Camaro, Firebird; Ball Joint; Upper

1993-02 Camaro, Firebird; Rack and Pinion Bellow Kit

1993-02 Camaro/Firebird; Tie Rod End; Inner; LH/RH

Moog reproduction tie-rod end for various GM models. Restores vehicle handling, and OE alignment. Reduces tire wear, and improves steering response. Each tie-rod end includes: (1) Tie Rod End, (1) Jam Nut. Specifications:...

1993-02 Camaro and Firebird; Control Arm Bushing; Lower

Reproduction tie-rod end for various GM models. Restores vehicle handling, and OE alignment. Reduces tire wear, and improves steering response. Each tie-rod end includes: (1) Tie Rod End, (1) Castle Nut, (1) Cotter Pin, (1)...

1993-02 Camaro and Firebird; Tie Rod End; Outer; LH/RH

1978-96 Regal, 1993-88 C1500; Stabilizer Bar Bushing; Front; 1-7/16" Bar

1967-69 Camaro; Stabilizer Bar Link Kit; Black

1973-77 Regal; Stabilizer Bar Link Kit; Front

1973-77 Regal; Stabilizer Bar Link Kit; Front

1973-87 Regal; Ball Joint; Front; Lower

Our Power Steering Conversion Hose kit is designed to fit the GM Saginaw power steering pump with inverted flare pressure fitting. It also fits the GM 605, 800 and 600 Series power steering gear box! These hose kits are the...

Our Power Steering Conversion Hose kit is designed to fit the GM Saginaw power steering pump with inverted flare pressure fitting. It also fits the GM 605, 800 and 600 Series power steering gear box! These hose kits are the...

Repair torn and worn-out tie rod end boots without having to purchase the entire tie rod. Add durability surpassing most OEM rubber boots with this quality reproduction. Manufactured in high performance polyurethane for added...

Repair torn and worn-out tie rod end boots - without having to buy the entire tie rod. Add durability surpassing most OEM rubber boots. Exclusive octagon style features 5-point sealing action. Made of high performance...

Repair torn and worn-out tie rod end boots without having to purchase the entire tie rod. Add durability surpassing most OEM rubber boots with this quality reproduction. Manufactured in high performance polyurethane for added...

When replacing or just repacking your wheel bearings, don?t use ordinary grease. Protect those bearings with a high quality, high temperature bearing grease. This is a very stable aluminized complex thickened grease used for...

Universal joints are used for installation of ididit tilt steering columns when an adjustment of geometry is necessary Made in USA

Manufactured and inspected to OEM-level standards, Centric?s OE replacement axle shaft bearings are guaranteed to enable smooth, easy wheel rotation with their optimally configured friction and load handling. Sold...

When it comes time to install bearing races, you?ll find this tool to be an excellent way of saving time. Includes all you need to install or remove bearing races.

This tool is great for pulling oil or grease seals. Convenient tool that comes in handy when needed.

To complete your ididit steering column installation, you should also replace your rag joint. When installing an ididit column in your car, you must use the correct application to match the column output shaft. Made in USA