Product#: 3415

Bumper Bolt with Conical Keps Hex Nut; Polished Stainless Steel Capped Head; 3/4" Diameter; 3/8-16" x 1"; Zinc Plated

Reproduction GM bumper bolt for a variety of General Motors and Chrysler applications. Each zinc-plated steel carriage bolt features a polished stainless steel cap for superb cosmetic appearance, corrosion resistance and long...

Product#: 2710

Chrome Trim Screw, #8 x 3/4", With #8 Phillips Oval Head

Replacement chrome plated trim screws used on various GM vehicles. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is original...

Product#: 8610

Flat Washer; 1/2" USS; Zinc Plated

1/2" USS zinc plated Flat Washer for a variety of applications. A washer is a thin plate (typically disk-shaped) with a hole (typically in the middle) that is normally used to distribute the load of a threaded fastener, such...

Product#: 13757

1965-69 Impala, Camaro, Bel Air, Firebird; Hood Insulation Fastener; Black Nylon

Replacement black nylon 2" square head hood insulation retainer is just what your classic vehicle needs to keep your original hood insulation where it belongs...attached to the hood. This retainer is a service replacement for...

Product#: 3798372

1962-84 Windshield Washer Jar Cap ; Various GM Models

Reproduction of the original windshield washer jar cap designed for use on a variety of GM models including 1967-74 Camaro models. This cap is manufactured in injection molded ABS and replicates the original. Features correct...

Product#: 548935

1962-1977 GM; Windshield Washer Jar Bracket; Various Models

OER® replacement of the original windshield washer jat bracket designed for use on various 1962-77 GM models as listed. This bracket is manufactured in stamped steel and features an EDP coating for rust resistance. This...

Product#: 9785616

1955-82 Spare Tire Hold Down Nut; 5/16"-18 Thread; 3.88" Wide; Zinc Finish

OER® reproduction wing nut for many GM models. This spare tire hold down nut is used in conjunction with the spare tire hold down rod. Manufactured in stamped steel and features correct threads and wing nut design....

Product#: 3764424

1962-72 Chevrolet/Pontiac; OE Style Firewall Pad Fastener; Plastic; 7/16" X 1.50"; Various Models

Correct reproduction plastic firewall pad fastener for various GM models including 1967-69 Camaro, 1967-69 Firebird, 1962-72 Nova and 1962-69 Impala models. These fasteners are required to allow the firewall pad to attach...

Product#: 10362

Bolt, 5/16-18 x 13/16" Pointed Tip With Hex Washer Head, Black Phosphate

OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. Note: For a money saving set of 10 use...

Product#: 3899508

1959-80 Trico Windshield Wiper Blade; 15" Length; Various Models; Each

Reproduction 15 inch "TRICO Style # PR-15-2W" wiper blade for a wide variety of classic vehicle models. Each blade features stainless steel construction and is loaded with a period-correct TRICO RF-15 style insert with a...

Product#: CX2048

1963-67 Chevrolet Corvette; Rear Bumper; Chrome; Driver Side; LH

Reproduction rear chrome bumper for 1963-67 Chevrolet Corvette models. Manufactured to factory specifications featuring correct mounting points and triple chrome plating. LH driver side. {fitment}

Product#: CX2049

1963-67 Chevrolet Corvette; Rear Bumper; Chrome; Passenger Side; RH

Reproduction rear chrome bumper for 1963-67 Chevrolet Corvette models. Manufactured to factory specifications featuring correct mounting points and triple chrome plating. RH passenger side. {fitment}

Product#: CX2044

1963-67 Chevrolet Corvette; Chrome Front Bumper; LH Driver Side

Reproduction of the original front bumper for use with 1963-67 Chevrolet Corvette models. Each bumper is manufactured to correct factory specifications offering an authentic appearance anf fitment. Features a triple chrome...

Product#: CX2045

1963-67 Chevrolet Corvette; Chrome Front Bumper; RH Passenger Side

Reproduction of the original front bumper for use with 1963-67 Chevrolet Corvette models. Each bumper is manufactured to correct factory specifications offering an authentic appearance anf fitment. Features a triple chrome...

Product#: HK231

1956-62 Corvette; Convertible Top Motor Pump Assembly; Original Style; Made in the USA!

Reproduction top motor made to provide consistent hydraulic pressure and dependability. Raise and lower the power top with ease. The motor comes complete with rubber mounts. Features original style mounting locations as well...

Product#: K51020

1962-76 GM, Dodge, Plymouth; Various Models; Convertible Top Boot Vinyl Storage Bag

Why leave your top boot in the trunk exposed when you can keep it safe and clean by safely storing it in this special top boot vinyl storage bag. The storage bag will help protect your vehicles top boot while being stored in...

Product#: 4753019

1959-72 Buick; Chevrolet; Oldsmobile; Pontiac; Trunk Lock Latch Assembly; Manual; Various GM Models

This OER® reproduction of the original manual trunk lid latch assembly. This correct reproduction installs in the trunk area and is connected to the trunk lock cylinder by the handle shaft. Allows the trunk lid to lock...

Product#: 3825828

1963-67 Chevrolet, Oldsmobile, Pontiac; Hood Hinge Assembly; RH Passenger Side

Reproduction hood hinge assembly for various 1963-67 GM models. Each hood hinge is manufactured from stamped steel to factory specifications assuring a quality replacement. Features correct mounting points for ease of...

Product#: 11503957

U-Nut; M6 - 1.0; Panel Range.030" to.160"; Center of Hole to Edge: 17/32"; Black Phosphate; Each

Black phosphate metric u-nut or foldover nut, that measures M6-1.0 to install and secure various components. Fits panel thickness from.80mm to 4 mm. (.030" to.160") Specifications: OE #: 11503957 Quantity: Individual Clip...

Product#: A1017

3/8"-16 x 15/16" Bumper Bolt With Flat; Zinc Plated Shank; Stainless Steel Flat Head; Each

Correct replacement style bolt to replace the original missing or damaged bumper bolt. Each bolt is manufactured to original specifications and will match the original. Fits a variety of different years and models. Measures...