Chevrolet All Models Parts - Accelerator Components

Pedal floor spacers are recommended when installing the pedal on vehicles with thick carpet or under carpet padding. Made in USA

Universal style accelerator throttle rod designed for use on various GM, Ford, Chrysler, Dodge, Plymouth models. This accelerator rod is for use when modifications will not allow the use of the original rod between the...

Lokar direct fit pedal pads for use with Lokar?s drive-by-wire throttle control assembly. The standard model measures 4" x 1-1/2" and the XL model measures 5" x 2". Both sizes are available in brushed and black finishes to...

The first spring loaded pedals in the industry! This chromed steel throttle assembly is spring loaded like the OE design, and features a removable, splined lower arm for versatile mounting to the right or left of the bracket...

Fits Holley 2300 and 2305 2 bbl. or Holley 4150 and 4160 4 bbl. carburetors mounted on any manifold.

This beautifully carved brushed billet aluminum throttle assembly has a spring-loaded pad like the OE design and features a splined removable lower arm for versatility in mounting to the right or left of the bracket. The...

Gleaming polish not your style? Then take a look at this stealthy black anodized billet spring-loaded throttle assembly that features a removable lower arm and is splined for versatile mounting to either the right or left...

Three piece universal billet aluminum pedal kits from Billet Specialties. This kit comes with easy to use drill templates and the necessary stainless steel hardware for installation. Made in USA Dimensions: Gas Pedal -...

Pedal floor spacers are recommended when installing on vehicles with thick carpet or carpet padding. Made in USA

This chrome throttle cable bracket can be used with all 4150 and 4160 model square bore Holley carburetors. It includes dual stainless steel return springs.

This beautifully carved brushed billet aluminum throttle assembly has a spring-loaded pad like the OE design and features a splined removable lower arm for versatility in mounting to the right or left of the bracket. The...

Pedal floor spacers are recommended when installing on vehicles with thick carpet or carpet padding. Made in USA

When using an electronic overdrive transmission, such as a 4L60E, with a carbureted engine, the transmission control unit requires a throttle position signal. This sensor bolts on to the carburetor and sends the proper...

Chromed steel brake pedal pad is designed with a 1/2"-20 thread and includes a 1/2"-20 stud in kit for mounting. Made in USA

Lokar direct fit pedal pads for use with Lokar?s drive-by-wire throttle control assembly. The standard model measures 4" x 1-1/2" and the XL model measures 5" x 2". Both sizes are available in brushed and black finishes to...

This beautifully carved brushed billet aluminum throttle assembly has a spring-loaded pad like the OE design and features a splined removable lower arm for versatility in mounting to the right or left of the bracket. The...

This chrome universal carb return bracket is designed to replace the original bracket for most carburetors. Adds a high performance touch to any carburetor.

This Lokar billet aluminum drive-by-wire electronic throttle control assembly is preprogrammed specifically for Ford Coyote 5.0L crate engines and will accept both factory and aftermarket wiring harnesses. Made in USA ...

Lokar direct fit pedal pads for use with Lokar?s drive-by-wire throttle control assembly. The standard model measures 4" x 1-1/2" and the XL model measures 5" x 2". Both sizes are available in brushed and black finishes to...

This beautifully carved brushed billet aluminum throttle assembly has a spring-loaded pad like the OE design and features a splined removable lower arm for versatility in mounting to the right or left of the bracket. The...

Stainless steel GM designed dual springs for use with Lokars SR4001 bracket (sold separately). Made in USA

The first spring loaded pedals in the industry! This chromed steel throttle assembly is spring loaded like the OE design, and features a removable, splined lower arm for versatile mounting to the right or left of the bracket...

Some vehicles, especially vehicles with air conditioning, require a throttle solenoid to automatically increase engine rpm. This throttle solenoid set from Demon Fuel Systems includes the solenoid, bracket, and mounting...

This Lokar billet aluminum drive-by-wire electronic throttle control assembly is preprogrammed specifically for Ford Coyote 5.0L crate engines and will accept both factory and aftermarket wiring harnesses. Made in USA ...

Pedal floor spacers are recommended when installing the pedal on vehicles with thick carpet or under carpet padding. Made in USA

Three piece universal billet aluminum pedal kits from Billet Specialties. This kit comes with easy to use drill templates and the necessary stainless steel hardware for installation. Made in USA Dimensions: Gas Pedal -...

Lokar direct fit pedal pads for use with Lokar?s drive-by-wire throttle control assembly. The standard model measures 4" x 1-1/2" and the XL model measures 5" x 2". Both sizes are available in brushed and black finishes to...

Gleaming polish not your style? Then take a look at this stealthy black anodized billet spring-loaded throttle assembly that features a removable lower arm and is splined for versatile mounting to either the right or left...

Correct reproduction of the original accelerator rod and pin designed for use with 1953-57 Chevrolet and GMC truck models. Will replace the missing or damaged original rod and pin allowing the accelerator to function...

Designed for bolt on installation, this bracket adapts the popular GM 10379038 or equivalent pedal to your 1967-68 Camaro. Remove the factory throttle linkage and bolt in place for a simple install. Adjustable to accommodate...

Rod that hooks from carburetor to upper control arm on passing gear lever.

Lokar's answer to LT cable problems. Stainless Throttle and Kickdown Brackets replace factory brackets. Kits include stainless arm to mount on throttle body to operate kickdown. Designed to be used with Lokar's Tuned-Port...

Reproduction of the complete accelerator pedal assembly which extends from the firewall on all V8-equipped 1967 Firebird models. This accelerator pedal assembly comes complete with the pedal, pedal mount pin and spring,...

Original GM bracket used to hold the cruise control module in place under the hood.

Reproduction of the original throttle arm designed for use with 1955-57 Chevrolet Bel Air, 150, 210, and Nomad 8 cylinder models. The throttle arm is manufactured in stamped steel to factory dimensions and replaces the...

Reproduction of the original style starter pedal pad designed for use with 1947-59 Chevrolet and GMC trucks. The foot starter pedal pad can crack and wear out over time. Replacing the pad will help the appearance of the...

Black Billet Aluminum. Single Hole Stud For Throttle Cable Only. Lokar throttle cable brackets are available for a variety of different motors including carbureted set ups, LS1, Ram Jet 350 & 502 and more. Carburetor...

Lokar 1955-57 Chevy fullsize passenger car models billet aluminum throttle pedal assembly is designed to bolt into the stock location on the firewall, allowing yout o change from the factory rod linkage to a modern throttle...

Reproduction of the original pedal pads designed for 1969-71 Camaro and 1970-71 Firebird models equipped with 3" brake and 2-3/8" clutch pedal. Each pad is manufactured to original factory specs! 8 piece set includes the 3"...

Lokars traditional flat style billet aluminum throttle pedal pad lets you retain the factory throttle linkage, with a updated look inside the car. The direct fit throttle pad replaces the factory pad, measures 2" x 5" and...

These CNC machined pedal pads are specifically designed to compliment your Billet Specialties gas pedal. Each pad includes all the stainless steel hardware needed for a quick and clean install. Note: Replaces factory pad.

This complete kit is designed to replace pedal pads and trim plates on 1970-71 models with floor mounted gas pedal , drum brakes and a manual transmission. For models with the 3" clutch pedal. To ensure proper fit, measure...

This billet aluminum cable bracket from Lokar mounts to the side of your TPI intake plenum and allow you to install your throttle cable. Made in USA Black billet aluminum. Single hole stud for throttle cable only.

Give your cockpit a serious, hardcore look with these Dark Series billet pedal covers for the Generation 5 Camaro. Machined from 6061-T6 billet aluminum, these pedals are then finished in flat black anodized hard coat and...

Looking to give your pedal assembly a modern look? Look no further. Give your interior a fresh look with a Muscle Car Pedal set. This is a direct bolt in assembly, manufactured from lightweight aluminum and features graphite...

Reproduction of the original accelerator pedal pad rod designed for use on Camaro and Nova models. This rod connects between the throttle arm and the accelerator pedal. Manufactured in correct configuration, replaces the bent...

This throttle rod adapter removes the guesswork when installing a Street Demon carburetor using mechanical linkage in almost any carbureted GM application. All brackets have a clear zinc coating for corrosion protection and...

Lokar 1962-67 Nova billet aluminum throttle pedal assembly is designed to bolt into the stock location on the firewall, allowing you to change from the factory rod linkage to a modern throttle cable set up. The traditional...

This is the retainer bracket which holds the rear loop of the throttle return spring in place. This bracket which mounts on top of the coil bracket was used on 1968-70 Camaro, Nova, Impala, Bel Air, and Caprice models with a...

These aluminum pedal covers are unique to the market as they actually bolt-on to your pedal instead of clamping on like most aftermarket pedal covers. Manufactured with a hard coat black anodized inner and a brushed aluminum...

Reproduction of the original throttle arm designed for use on 1968-69 Camaro models. Each throttle arm is produced to replicate the original in quality and fit. Replace your worn out or damaged original throttle arm with this...

These aluminum pedal covers are unique to the market as they actually bolt-on to your pedal instead of clamping on like most aftermarket pedal covers. Manufactured with a hard coat black anodized inner and a brushed aluminum...

Sprint Booster is a plug & play electronic device which attaches to your accelerator pedal, and eliminates the delay of electronic throttle response, providing instant acceleration. Available in a Version2, and Version3....

Correct reproduction of the commonly missing spring which inserts between the carburetor and water neck. Fits 1976-79 models with L6 engine (outer)

Chrome plated bracket is precision stamped for a secure attachment which prevents from rotating out of position. Features a slotted design to fit most applications. Note: Match with T9756 for accurate function and...

Lokar 1968-72 Nova billet aluminum throttle pedal assembly is designed to bolt into the stock location on the firewall, allowing you to change from the factory rod linkage to a modern throttle cable set up. The traditional...

Pedal floor spacers are recommended when installing the pedal on vehicles with thick carpet or under carpet padding. Made in USA

This billet aluminum cable bracket from Lokar mount to the side of your TPI intake plenum and allow you to install your Throttle, Kickdown, and Cruise Control cable. Made in USA

Reproduction of the original accelerator throttle cable bracket for use on 1970-72 Camaro and Firebird models with Holley Carburetors. This quality bracket is manufactured in stamped steel to the original factory...

Correct support assembly which supports the accelerator rod through the firewall. Each support is designed and manufactured to replace the craked or missing original. For use on various GM applications. Applications:...