DeSoto All Models Parts - Suspension

Original replacement screw-in style lower ball joint for select Chrysler B-body models. These OE quality ball joints meet or exceed factory specifications. Sold individually. Note: Threaded ball joints are distinguishable by...

Standard design strut rod bushing kit for 1957-65 Chrysler/Pymouth/Dodge B-body vehicles. These rubber bushings are factory replacement for various models listed. They will meet or exceed the factory ride and handling. 1 kit...

Correct replacement self locking nuts used on various GM vehicles. Zinc plated. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is...

This 5/16-inch medium split stainless steel washer is for use with 18-8 fasteners. Product Specifications: Stainless steel medium split washer Size: 5/16-inch Outer diameter: 19/32-inch Minimum thickness: .078-inch

Mustang II Coil Spring Ride Height Adjuster Kit.

This 1/4-inch stainless steel medium split lock washer is for use with 18-8 fasteners. Product Specifications: Stainless steel medium split washer Size: 1/4-inch Outer diameter: 31/64-inch Minimum thickness: .062-inch

This 5/16"-24 "Keps" lock washer and nut is zinc plated steel and is sold as each. Product Specifications:Keps lock washer and nut Zinc plated steel Thread size: 5/16"-24 Hex width: 1/2"

This is a stainless steel 5/16-18x1-inch hex head cap screw that has many uses for your project vehicle. Specifications: Thread Size : 5/16-18 Length : 1" Thread Length : Partial Head Style : Hex Material : 18-8 Stainless...

This hex head sems tapping screw is 5/16-inch 18x3-inch and has a 5/8-inch attached washer. Product Specifications: Hex head sems tapping screw Phosphate M4.2-1.41 x 20mm (#8 x 25/32") Washer O.D.: 16mm (5/8-inch) 7mm hex...

This stainless steel 5/16-inch flat washer is for use with 18-8 fasteners. Product Specifications: Stainless steel commercial flat washer Bolt size: 5/16-inch Inner diameter: 11/32-inch Outer diameter: 3/4-inch Approximate...

This 1/4-inch x 7/16-inch steel acorn cap nut is nickel plated. Product Specifications: Steel acorn cap nut Nickel plated Thread size:1/4"-20 Hex width: 7/16" Height: 3/8"

Replacement push on round flat nuts used on various vehicles. Zinc plated. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is...

This 1/2"-13 zinc plated steel lock nut is sold as each.

Adjust vehicle height at the push of a button while maintaining balanced air springs. The RidePro E5 control system tunes air ride suspension for proper handling and world-class ride quality by way of sophisticated pressure...

In case you lost or just need a jam nut for your QA1 coilovers we now have them.

Universal Polyurethane Sway Bar End Link Grommets and Washers Universal - Set of 8 Inner Diameter - 3/8" Nipple Outer Diameter - 11/16" Outer Diameter - 1-1/8" Height - 0.725"

Designed to fit most leaf springs, these bars strengthen rear suspension and reduce wheel hop. They are constructed from heavy gauge rectangular steel and feature MIG welded brackets for extra strength. Rubber snubbers,...

Universal Spring Isolators - Red. Made of superior HYPERFLEX polyurethane material. Saves replacing again and again lasting from 3 to 10 times longer than rubber isolators. Pad Details Inside Diameter - 2-1/8" Lip Outside...

Fits 25mm (1 Inch) Sway Bars Only

Reproduction control arm bushing for the lower control arm on various 1971-05 GM and various other models. Manufactured in steel clad rubber to be pressed into place. If your suspension rattles or makes noises when turning...

Adjust vehicle height at the push of a button while maintaining balanced air springs. The RidePro E5 control system tunes air ride suspension for proper handling and world-class ride quality by way of sophisticated pressure...

Our Mustang II drop spindles are built from forged steel and heat treated for superior strength. Designed to drop the front end approximately 2" lower than stock while maintaining stock geometry. Will fit 1974-78 Ford...

7/16" F436 Washer. ASTM F436 covers the chemical and mechanical requirements for hardened washers in diameters ranging from 1/4? to 4? inclusive. These heat treated washers are for general purpose and structural use. For use...

CPP's Mustang II stock height front spindles are built from forged steel and heat treated for superior strength. Will fit 1974-78 Ford Mustang, 1974-80 Ford Pinto, and 1975-80 Mercury Bobcat. Mustang II style spindles are...

Speed nuts for various original or reproduction emblems that include 5/16" mounting studs. This speed nut set can be utilized for many of the emblems that don't include attaching nuts. Set includes 8 speed nuts without...

Our Mustang II stock height front spindles are built from forged steel and heat treated for superior strength. Will fit 1974-78 Ford Mustang, 1974-80 Ford Pinto, and 1975-80 Mercury Bobcat. Mustang II style spindles are also...

Nut 7/16"-20 Grade 8 Hi .625 Tall, 11/16 Hex Head. Hex nuts are six-sided, internally threaded fasteners, mated with bolts, studs, screws, and other externally threaded products. The addition of the hex nut ensures that the...

Specifications: Diameter: 5/8" Width: 2-3/4" Length: 9" Features: Includes Nuts E-Coated For Corrosion Resistance Ductile Iron With Fixed Center Pins

CPP's Mustang II drop spindles are built from forged steel and heat treated for superior strength. Designed to drop the front end approximately 2" lower than stock while maintaining stock geometry. Will fit 1974-78 Ford...

Prothane universal style greasable sway bar bushings for classic Mustang. These bushings feature have a grease fitting built into the heavy duty brackets for convenient lubrication and contoured grooves molded into the...

Prothane universal style greasable sway bar bushings for classic Mustang. These bushings feature have a grease fitting built into the heavy duty brackets for convenient lubrication and contoured grooves molded into the...

Speed nuts for various original or reproduction emblems that include 5/16" mounting studs. This speed nut set can be utilized for many of the emblems that don't include attaching nuts. Set includes 4 speed nuts without...

Designed to fit most leaf springs, these bars strengthen rear suspension and reduce wheel hop. They are constructed from heavy gauge rectangular steel and feature MIG welded brackets for extra strength. Rubber snubbers,...

Black phosphate coated hex head bolts with washer. Measures 3/8-16 x 1" SEMS with 1" outside diameter to fit a variety of applications, including the hood latch on 1970-81 Firebird, and 1973-80 Chevrolet or GMC truck, among...

Fits 25mm (1 Inch) Sway Bars Only

RidePro-HP ride height sensors upgrade your existing RidePro-X pressure-based system. The ultimate air suspension management system measures BOTH pressure and ride height. With the addition of RidePro-Hp ride height and...