Product#: UK915

Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 36" Long

This universal anti-squeak insulator set includes two rubber strips that insert in between the gas tank and the mounting straps to eliminate any noise from tank movement and vibration which may occur. One foam rubber pad...

Product#: AL124

Accelerator Throttle Rod; Universal Fit

Universal style accelerator throttle rod for various GM, Ford, Chrysler, Dodge, Plymouth models. This accelerator rod is for use when modifications will not allow the use of the original rod between the accelerator pedal...

Product#: C67808

Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 39" Long; For 1" Wide Straps

Universal style anti squeak cushions are designed to install between the gas tank and the gas tank straps. These fuel tank anti squeek pads cushion the gas tank from the body and straps to reduce noise caused by metal to...

Product#: CX5042

1965-97 GM; Fuel Tank Sending Unit; 0-90 Ohm; Universal Fit; For 6" to 24" Deep Fuel Tanks; Without Pick-Up Tube

Universal fuel tank sending unit for various 1965-97 Chevrolet and GMC trucks with custom tank under the bed and other GM models 1965 and later, that require a 90 ohm sender. Designed for use with OE or aftermarket 0-90 ohm...

Product#: 9202A

1948-86 Ford; Fuel Tank Sending Unit Brass Float; Various Models

Reproduction of the original style and correct brass float for use with various 1948-86 Ford and Mercury models as listed below. This sending unit brass float is desirable for its long-lasting dependability as it lasts much...

Product#: 153665B

Throttle Cable 36"" Cut-To-Fit; Stainless Steel; Black

This throttle cable is designed with a specially extruded liner to extend the life of the cable. Cables are equipped with aluminum fittings and aluminum ferrule to eliminate fraying. Clevis is designed to eliminate cotter...

Product#: 9047G

Fuel Filler Hose; Nitrile 70 Shore Rubber; 2" ID x 20" Length

Fuel filler hose to connect fuel neck to fuel tank on a variety of models requiring a 2" ID fuel hose. This hose can be used as is, or if you require a shorter piece, you can cut this 20" fuel hose to your desired length....

Product#: 9047E

Fuel Filler Hose; Nitrile 70 Shore Rubber; 2" ID x 15" Length

Reproduction fuel filler hose to connect fuel neck to fuel tank on a variety of models requiring a 2" ID fuel hose. This hose can be used as is, or if you require a shorter piece, you can cut this 15" fuel hose to your...

Product#: A4700298

1977-78 Mustang II, Pinto, Bobcat; Fuel Tank Mounting Straps; Pair

Reproduction of the original fuel tank mounting straps designed for use with 1977-78 Mustang II, Pinto, and Bobcat models. Manufactured with high strength corrosion-resistant steel to factory dimensions. Straps measure...

Product#: A4700297

1974-76 Mustang II, Pinto, Bobcat; Pair; Fuel Tank Mounting Straps; ST297; Pair

Reproduction of the original fuel tank mounting straps designed for use with 1974-76 Mustang II, Pinto, and Bobcat models. Manufactured with high strength corrosion-resistant steel to factory dimensions. Straps measure...

Product#: TF700512

Spring Steel Rod Clip, Fits 1/4" Rod Diameter, RH, 17/64" ID.

Correct style rod clip used on various GM vehicles. Fits 1/4" rod diameter, RH, 17/64" ID. These reproduction transmission linkage rod clips need to be replaced when replacing your linkage rods. 1955-57 Chevrolet Transmission...

Product#: 92L010

1966-96 Ford, Mercury; Lower Fuel Tank Filler Pipe Seal; Various Models

Reproduction of the original fuel tank to filler pipe seal designed for use on various1966-97 Ford and Mercury applications. Each seal is manufactured to correct factory specifications and replaces the old or missing original...

Product#: 14048

1958-88 Holley Carburetor Fuel Bowl Screw; 2-1/2"

Reproduction 2-1/2" flat blade carburetor fuel bowl screw for Holley carburetors. This special screw is specifically designed in the correct original configuration and head design for the early model Holley carburetors. Many...

Product#: K915

Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 24" Long; For 1" Wide Straps

Reproduction fuel tank anti squeek set for vehicle models. Includes one 5-1/4" x 2" x 1/2" precision die cut neoprene tank to floor cushion, two 24" x 1-1/4" molded rubber strap to tank cushions, and two 24" x 2 " x.060" flat...

Product#: T76063

Billet Aluminum; Fuel Filler Neck; with Pop-Up Gas Cap

Billet aluminum flush mount fuel filler neck with pop-up gas cap is the perfect addition to your classic car or truck when adding a non-stock fuel filler location or relocating your fuel tank. Features a super sanitary and...

Product#: 1256633

1955-79 Air Cleaner to Carb Gasket; 5-1/8".060" Thick; Various Models; Universal Fit

Reproduction air cleaner to carburetor gasket manufactured for use with any 2 bbl or 4 bbl carburator with a 5-1/8" base. Can be used with any small or big block engine. Fits most 1964 and newer Ford applications, most 1965...

Product#: CX5041

1931-64 GM; Fuel Tank Sending Unit; 0-30 Ohm; Universal Fit; For 6" to 24" Deep Fuel Tanks; Without Pick-Up Tube

Universal fuel tank sending unit for various 1931-53 Chevrolet and GMC trucks with custom tank under the bed and other GM models up to 1964 that require a 30 ohm sender. Designed for use with OE or aftermarket 0-30 ohm...

Product#: TK0121

Fuel Tank Sending Unit; 5 Hole; "Universal" 240-33 Ohm; For Many Aftermarket Gauges

Our universal fuel tank senders mount with five mounting screws. They work on fuel tanks from 6 to 24 inches deep by cutting to length using the instructions included. Since fuel tank senders only read resistance to ground...

Product#: 14305

Carburetor Float Bowl Screws; Set of 8; For Holley Carburetors

Reproduction set of 2-1/2" slotted head carburetor fuel bowl screws for Holley carburetors. These special screws are designed in the correct original configuration with the proper head design for the early model Holley...

Product#: 1308EDL

Edelbrock VRS-4150 850 CFM Performance Carburetor #1308; Mechanical Secondary; Aluminum; Natural Finish

Edelbrock VRS-4150 race & performance 850 CFM carburetor is street friendly but race ready. The 3.75"-tall cast aluminum main body fits all 4150 and 4500 carb flange manifolds without requiring an adapter plate. Multiple...