Plymouth Barracuda Parts - Rear End

Max-Gear is an ultra-tough automotive gear oil. It?s designed to maximize power and provide unsurpassed protection to heavily loaded gears. It makes gears run smoother, quieter, cooler and longer without overhauls. Max-Gear...

Max-Gear is an ultra-tough automotive gear oil. It?s designed to maximize power and provide unsurpassed protection to heavily loaded gears. It makes gears run smoother, quieter, cooler and longer without overhauls. Max-Gear...

Impress those behind you with a chrome differential cover. This cover is for Dana 60 rear-axles, includes the gasket, fill plug and chrome bolts.

Motive Gear offers some of the toughest drivetrain components on the market today. Their products can be found in the winner's circle at NHRA, IHRA and NASCAR events. The superior quality components is the result of years of...

These u-joint u-bolt kits are designed for use on stock and Yukon pinion yokes with 1310 u-joint size. Includes: two u-bolts (3/8" X 1-11/16") and four nuts. Made in the USA.

Replacement thrust spacer set for 8-3/4" differentials with clutch type Sure-Grip prior to 1970. Required to provide axle thrust surface in four-spider differential applications. One set required per vehicle.

Used by Joe Gibbs Racing in every rear end differential and transmission gear box. This fully synthetic, unique SAE 75W-110 gear oil reduces operating temperatures by up to 15 degrees compared to other brand gear oils.

Mopar 8-3/4" "89" case housing

This locking pawl and flanged nut is used on the right side axle of 8-3/4" differentials. The pawl secures the axle end play adjusting nut once proper bearing play is established.

Used by Joe Gibbs Racing in every rear end differential and transmission gear box. This fully synthetic, unique SAE 75W-110 gear oil reduces operating temperatures by up to 15 degrees compared to other brand gear oils.

Used by Joe Gibbs Racing in every rear end differential and transmission gear box. This fully synthetic, unique SAE 75W-110 gear oil reduces operating temperatures by up to 15 degrees compared to other brand gear oils.

This is a high strength axle shaft for Mopar muscle cars equipped with an 8-3/4" rear end. Yukon axles are made from 1541H alloy and are deeply heat-treated to be 20-25% stronger than OEM 1040/1050 steel axles. The axle...

Did you know the rear axle housing was shipped to the assembly plant without the brake lines and fittings in place? A special piece of tape covered the vent hole to keep debris & moisture out during shipping. The plant then...

The Moser Muscle Pak gives you a complete axle assembly ready to install in your Mopar. Assembly work has been completed by Moser's expert technicians, all you have to do is add gear oil! You get a brand new Moser stamped...

The Moser Dana 60 Muscle Pak gives you a complete axle assembly ready to install in your Mopar. Assembly work has been completed by Moser's expert technicians, all you have to do is add gear oil! You get a brand new Moser...

The Moser Muscle Pak gives you a complete axle assembly ready to install in your Mopar. Assembly work has been completed by Moser's expert technicians, all you have to do is add gear oil! You get a brand new Moser stamped...

The Moser Muscle Pak gives you a complete axle assembly ready to install in your Mopar. Assembly work has been completed by Moser's expert technicians, all you have to do is add gear oil! You get a brand new Moser stamped...

The Moser Dana 60 Muscle Pak gives you a complete axle assembly ready to install in your Mopar. Assembly work has been completed by Moser's expert technicians, all you have to do is add gear oil! You get a brand new Moser...

Original quality replacement rear differential cover gasket. New gaskets should always be used whenever removing or replacing rear end covers. Applications: A-Body 1961-62 Lancer 1961-74 Valiant 1963-74 Dart 1964-69...

This yoke is manufactured specifically for Mopar differentials. Available as a cast iron reproduction. Includes the yoke, and mounting hardware. Important: Use MM3095 strap kit, Note: Uses 7290 series U-joints (sold...

This cast iron reproduction yoke is manufactured specifically for Dana 60 rear axles. Includes the yoke, retaining u-bolt, and mounting hardware. Note: Uses 1330 series U-joints (sold separately) that have a 3.625 " snap...

These Pro-Series ring gear bolt kits from ARP are forged from premium-grade 8740 chromoly steel and heat-treated to a rating of 190,000 psi. This is a set of 12 3/8"-24 LH threaded bolts for the 8-3/4" ring gear. Made in...

The Moser Muscle Pak gives you a complete axle assembly ready to install in your Mopar. Assembly work has been completed by Moser's expert technicians, all you have to do is add gear oil! You get a brand new Moser stamped...

The Moser Muscle Pak gives you a complete axle assembly ready to install in your Mopar. Assembly work has been completed by Moser's expert technicians, all you have to do is add gear oil! You get a brand new Moser stamped...

Get rid of underperforming leaf springs with the Street-Lynx Triangulated 4-Bar System. This system drastically improves geometry, traction, and handling by separating the locating system from the spring, while lighter...

Chrome differential cover bolts for 8-1/4" rear axles. Each set includes enough bolts to mount the differential cover to the axle housing.s

This chrome moly billet yoke is manufactured specifically for Mopar differentials. Includes the yoke, u-bolt, and mounting hardware. Note: Uses 7260 series U-joint (sold separately) that have a 2.125" snap ring sp an with a...

This is a quality replacement U-joint for your Mopar. Features: Cap dia. 1-3/16" and 1-1/16" Forged and case hardened alloy steel crosses Heat-treated needle bearings Cold-formed radial bearing cups for 360° lubrication...

Ring gear bolts for Mopar 8-1/4" and 8-3/4" differentials. These are factory replacement quality. Sold as a set of 12.

This cast iron yoke is manufactured specifically for Mopar differentials. Includes the yoke, and mounting hardware. Important: Use MM3311 s trap kit, Note: Uses 7260 series U-joint (sold separately) that have a 2.125" snap...

Required and approved by all major racing sanctioning bodies this universal driveshaft safety loop is fully adjustable to fit most vehicles. The four piece design is manufactured from 1/4" thick, 2" wide mild steel, bright...

This forged steel reproduction yoke is manufactured specifically for Dana 60 rear axles. Includes the yoke, retaining u-bolt and mounting hardware. Note: Uses 1350 series U-joint (sold separately) that have a 3.62 5" snap...

Ring gear bolt for Mopar 8-1/4" and 8-3/4" differentials. This is factory replacement quality. Sold individually.

This is a quality replacement U-joint for your Mopar. Features: Forged and case hardened alloy steel crosses Heat-treated needle bearings Cold-formed radial bearing cups for 360° lubrication distribution Superior-quality...

This cast iron reproduction yoke is manufactured specifically for Dana 60 rear axles. Includes the yoke, retaining strap and mounting hardware. Note: Uses 1350 series U-joint (sold separately) that have a 3.625" s nap ring...

Ring gear bolts for Mopar 8-1/4" and 8-3/4" differentials. These are genuinely direct from Mopar Performance. Sold as a set of 12.

The Moser Dana 60 Muscle Pak gives you a complete axle assembly ready to install in your Mopar. Assembly work has been completed by Moser's expert technicians, all you have to do is add gear oil! You get a brand new Moser...

Work on your differential third member safely and easily with this lightweight fixture. It can be clamped or bolted to your work bench or simply mounted in a vise, and it fits neatly in your tool chest when the job is...

Did you know the rear axle housing was shipped to the assembly plant without the brake lines and fittings in place? A special piece of tape covered the vent hole to keep debris & moisture out during shipping. The plant then...

Mopar 8-3/4" "89" case housing

These u-joint strap kits are designed for use on stock and Yukon pinion yokes with 1350 u-joint size. Includes: two straps and four bolts. Made in the USA.

Mopar 8-3/4" "89" case housing

This set is for use on Dana 60, or any other rear end using 3/8"-16 x 3/4" bolts. Includes 12 chrome finished bolts and 12 Flat washers (not chromed).

Replacement crush sleeve for setting up your rear axle. Crush sleeves cannot be reused if you are changing a ring and pinion or the front seal. Includes pinion nut washer and pinion flange nut. These are for the 9-1/4"...

Max-Gear is an ultra-tough automotive gear oil. It?s designed to maximize power and provide unsurpassed protection to heavily loaded gears. It makes gears run smoother, quieter, cooler and longer without overhauls. Max-Gear...

Reproduction rear and housing e-brake, and brake line clip set for all 1960-76 models. Replace your rusted originals with these correct replacements. Must be welded to the factory locations.

FilterMag?s powerful rare-earth magnet trap and hold wear inducing metal particles smaller than 40-microns down to 1-micron. The super-strong magnetic force holds FilterMag to the cover, is reusable and will reduce...

Enhance the appearance of you GM 10 or 12-bolt rear end with ARP's stainless steel rear cover bolts. These bolts add a lustrous contrast to a painted OEM cover, compliment a chrome plated aftermarket version or add flash to...

Mancini Racing's driveshaft safety loops will contain the driveshaft in case of a front U-joint failure, keeping it from contacting the track and possibly flipping the vehicle. Loop uses existing factory OEM chassis mounting...

Factory-style replacement rear axle bumpers for 1970-73 E-body vehicles. Axle bumpers prevent the axle from slamming against the frame if the suspension is ever "bottomed out." Sold as a pair. Note: Moun ting hardware is...

Replacement 29 spline yoke for Chrysler 8-3/4" rear end applications with 1-7/8" pinion stem. Designed to be a high strength factory-style replacement for the original. Note: Uses 7290 series U-joints (sold separa tely) that...

Yukon master overhaul kit for Chrysler 8.75" rear ends. Included in this kit are Timken carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, oil...

Yukon master overhaul kit for Chrysler 8.75" rear ends. Included in this kit are Timken carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, oil...

Auburn Gear?s Pro Series limited-slip differential outperforms standard OEM differentials hands down. It delivers more traction and faster engagement for controlled power transfer and lightning fast reaction to changing load...

Factory-style replacement rear axle bearing retainer gasket for most 1960-76 A, B and E-Body Dodge and Plymouth models. For use with 8-3/4", 9-1/4" and 9-3/4" rear ends. Made in USA

This cast iron reproduction yoke is manufactured specifically for Dana 60 rear axles. Includes the yoke, strap, and mounting hardware. Note: Uses 1310 series U-joints (sold separately) that have a 3.219" snap ring span with...

This forged steel yoke is manufactured specifically for Mopar differentials. Includes the yoke, and mounting hardware. Important: Use MM3310 strap kit, Note: Uses 1350 series U-joint (sold separately) that have a 3.625"...

This billet steel yoke is manufactured specifically for Mopar differentials. Includes the yoke, and mounting hardware. Important: Use MM3307 u-bolt kit, Note: Uses 1350 series U-joint (sold separately) that have a 3.625"...