Plymouth Cuda Parts - Door Components

This is a correct reproduction of the original threaded striker washer for use on 1965-02 models. The door lock striker washer is installed on the door jamb for either the right or left hand door.3.50mm thick. 2 required...

Replacement style clip dessigned for use on many different GM models including Camaro. Replaces GM part numbers 4234830 and 12337868. Use as required. Correct hardware can make any installation job easier. Replace your...

Shaved Doors Billet Cable and Knob Emergency Entry Kit

The handles can be modified to fit any door handle and adds a phenomenal look to your ride while delivering simple form and function. The handles are handcrafted in house at Kindig-It Design and can be ordered in two...

Reproduction of the original door striker bolt shim manufactured in die-stamped steel and finished in clear zinc coating. Used to correctly position the door striker bolt for proper alignment with the door latch assembly. Use...

The handles can be modified to fit any door handle and adds a phenomenal look to your ride while delivering simple form and function. The handles are handcrafted in house at Kindig-It Design and can be ordered in two...

Injection molded reproduction of the original plastic washer that pushes through the door glass. Exact reproduction of the original door glass roller washer.

Injection molded reproduction of the original plastic washer that pushes through the door glass. Exact reproduction of the original door glass roller washer.

Correct style rod clip used on various GM vehicles. Fits 5/32" rod diameter, RH offset, 1/4" hole size. Note: For LH offset clip use K4013.

This authentic lock rod clip is designed to hold the door lock knob rod assembly to the lower rod assembly which pivots up and down when the door lock knob is raised or lowered. This is an essential part that is required in...

The handles can be modified to fit any door handle and adds a phenomenal look to your ride while delivering simple form and function. The handles are handcrafted in house at Kindig-It Design and can be ordered in two...

Reproduction of the original door striker bolt shim manufactured in die-stamped steel and finished in clear zinc coating. Used to correctly position the door striker bolt for proper alignment with the door latch assembly. Use...

The handles can be modified to fit any door handle and adds a phenomenal look to your ride while delivering simple form and function. The handles are handcrafted in house at Kindig-It Design and can be ordered in two...

Correct style rod clip used on various GM vehicles. Fits 5/32" rod diameter, LH, 11/64" ID. Note: For LH offset clip use 3962782. Correct hardware can make any installation job easier. Replace your missing or damaged...

Correct style spring steel anti-rattle rod clips used on various GM vehicles from 1958-1966. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions....

The handles can be modified to fit any door handle and adds a phenomenal look to your ride while delivering simple form and function. The handles are handcrafted in house at Kindig-It Design and can be ordered in two...

Reproduction of the original door striker bolt shim manufactured in die-stamped steel and finished in clear zinc coating. Used to correctly position the door striker bolt for proper alignment with the door latch assembly. Use...

The handles can be modified to fit any door handle and adds a phenomenal look to your ride while delivering simple form and function. The handles are handcrafted in house at Kindig-It Design and can be ordered in two...

Correct replacement spring clip designed for various 1970-96 GM models. The door handle requires 1 spring clip per side. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with...

Correct replacement oval Phillips head door latch screws used on various GM vehicles from 1965-1981. 1/4-20 x 5/8". Cadmium plated. 6 piece set. Correct hardware can make any installation job easier. Replace your missing or...

Reproduction of the clip that retains the two inner door lock rods. This nylon clip joins the horizontal rod from the door latch with the verticle rod that the door lock knob screws on to. Sold individually. One required per...

Keep your door working properly by replacing the door latch/lock clips with these new clips. Complete sets are available for 1973-74 E-Body applications.

Reproduction of the door glass channel guides on 1970-72 Barracuda and Challenger models. Used to guide the door glass as it moves up and down inside the door. Every set includes the front guide, rear guide, and the front...

This universal 2 Window set comes with a chrome 2 switch driver's control panel, 1 individual chrome window switch, wiring harnesses and instructions. Note: These window switches are not designed to replace the OE style...

The doors of 1970-74 E-body models were extremely heavy and hard on the hinges, often causing them to wear out prematurely. Installing this new replacement hinge will allow your door to work properly and open and close the ...

Reproduction door lock link rods for all 1970-74 E-Body models. These rods connect the door lock cylinders to the door latch assembly, and are manufactured in the correct diameter stainless steel wire.

Reproduction of the original power window switch designed for use on 1969-77 Mopar Dodge, Plymouth and Chrysler models designed to install in the drivers side front door. This switch is manufactured with original style...

Reproduction of the original front door window regulator designed for use on 1971-1974 Plymouth Barracuda and Cuda models. All stamped steel construction, features correct splined shaft and correct retaining screw threads for...

This complete lock set is designed to replace your ignition, door, and trunk lock assemblies. Each set comes complete with coded locks with Pentastar keys, pawls, clips and gaskets. Note: Not for fiber-optic, tilt &...

Stop wearing your arm out every time you need some air. Enjoy fresh air at the flick of a switch! This power window conversion set includes the electric motors, window glass regulators and all necessary hardware for...

Reproduction of the original nylon door lock cylinder gasket for use on virtually all 1960-74 Mopar A, B and E-Body models. Each gasket is manufactured in quality nylon material to factory specifications. Replacing the door...

Complete set designed to replace your ignition and door lock assemblies. This lock set includes coded ignition and door locks with coded OEM keys, pawls, clips and gaskets. Note: Not for fiber-optic applications. ...

Keep your door working properly by replacing the door latch/lock clips with these new clips. Complete sets are available for 1970-71 E-Body applications.

Elevate your classic's style with these electronic exterior door handles from Lokar! Each billet door handle is made from 6061 T-6 billet aluminum and utilizes a weatherproof 12 volt pressure-pad switch to supply power to an...

Elevate your classic's style with these electronic exterior door handles from Lokar! Each billet door handle is made from 6061 T-6 billet aluminum and utilizes a weatherproof 12 volt pressure-pad switch to supply power to an...

Reproduction bottom glass stop for 1970-74 E-Body models. Manufactured from dense rubber material, as original. One required per door. Applications: 1970-74 Dodge Challenger 1970-74 Plymouth Barracuda, 'Cuda

Replacement door and trunk (clear) gasket. Available for most 1960-76 models.

Replacement door lock strikers for various 1970-76 Mopar models. Manufactured to function and fit like the original, but manufactured in bright stainless steel. Applications 1970-76 A-Body 2 door models 1970-74 B-Body 2 ...

Reproduction of the original style door hinge pins and bushings. These repair kits are designed for use on various 1966-76 A, B and E-Body models. The components in this kit will restore proper hinge action and reduce noise...

Elevate your classic's style with these electronic exterior door handles from Lokar! Each billet door handle is made from 6061 T-6 billet aluminum and utilizes a weatherproof 12 volt pressure-pad switch to supply power to an...

Elevate your classic's style with these electronic exterior door handles from Lokar! Each billet door handle is made from 6061 T-6 billet aluminum and utilizes a weatherproof 12 volt pressure-pad switch to supply power to an...

Reproduction quarter window roller sets for 1970-74 Mopar E-Body models. Each set includes all the necessary hardware and rollers to repair the both RH and LH rear quarter windows. Includes 2 rollers, 2 glass guides and 2...

When you are rebuilding your door hinges don?t stop at pins and bushings, make sure you replace those worn out springs at the same time. Replace the worn out hinge spring with this reproduction designed to fit and function...

This 22 piece hardware set services the inner door components associated with the proper mounting and operation of the glass/ regulator mechanism. Manufactured from high quality injection molded material just as original....

Elevate your classic's style with these electronic exterior door handles from Lokar! Each billet door handle is made from 6061 T-6 billet aluminum and utilizes a weatherproof 12 volt pressure-pad switch to supply power to an...

Replace your worn door locks with a coded door lock set complete with 2 coded lock cylinders, 2 OEM keys, lock pawls and retaining brackets. Applications: 1970-74 Barracuda 1970-74 'Cuda 1970-74 Challenger Note:Must use...

Replace your broken or missing window regulator arm clip that mounts where the arm meets the roller. Sold individually.

Reproduction of the original style rubber outside door lock cylinder gaskets designed for use on the various models listed below. Each gasket is manufactured to original specifications in gray color and matches the original...

Reproduction inner door handle rod sleeve for all 1960-76 models. Features the correct sized material and includes enough for both doors. Sold as a 6 ft. sleeve. Must trim as required.

Reproduction of the door glass channel guides on 1970-72 Barracuda and Challenger models. Used to guide the door glass as it moves up and down inside the door. Every set includes the front guide, rear guide, and the front...

Reproduction of the original front door window regulator designed for use on 1970 Plymouth Barracuda and Cuda models. All stamped steel construction, features correct splined shaft and correct retaining screw threads for use...

Having the right hardware is essential when your working on your Mopar. One of the more common issues you may encounter when having problems with your outer door handle is the lock rod clip. When your outer door handle won't...

Keep your door working properly by replacing the door latch/lock clips with these new clips. Complete sets are available for 1972 E-Body applications.

Reproduction door handles. Replaces pitted, worn or inoperative door handle assemblies. Features: Die Cast Metal like original American SAE Hardware Correct Riveted Gasket like original Includes mounting hardware Mopar...

Reproduction of the original front door window regulator designed for use on 1970 Plymouth Barracuda and Cuda models. All stamped steel construction, features correct splined shaft and correct retaining screw threads for use...

OER reproduction door glass guide for 1970-73 Dodge/Plymouth E-Body models. For use on 1970-73 1st design doors (not 1974). This glass guide installs on the glass and rides in the vertical channel guiding and giving the glass...

Nu-Relics standard GM-Style chrome power window switch and harness kit for door placement. This kit includes one quad switch for the driver door and three single pole switches for the passenger doors and/or quarter panels....

Reproduction of the original front door window regulator designed for use on 1971-1974 Plymouth Barracuda and Cuda models. All stamped steel construction, features correct splined shaft and correct retaining screw threads for...

Reproduction lower door hinge bolt set for 1970-74 E-Body models. Manufactured to look and fit like the originals.

Reproduction door hinge bolt set for 1966-70 B-Body and 1970-74 E-Body models. Manufactured to look and fit like the originals.