Plymouth All Models Parts - Electrical & Wiring

This flasher is recommended when upgrading to LEDs. Due to the lower current that LED lighting draws, the factory flasher may cause inconsistant flashing. Replaces the standard 552 flasher found on a wide variety of classic...

OE style replacement cloth insulator for electrical wires such as the temperature sender wiring harness. Measures 3/16" I.D., 5/16" O.D. Sold per foot. 2-3 feet required.

Mounts in 5/16" hole. 12 Volt operation. Made in USA

A hot exhaust manifold can cause serious damage to your electrical system. If not properly fastened, the wiring harness leading to your alternator/generator or other wiring harnesses could fall into an open area between the...

When upgrading your distributor, don't overlook this essential component.

In today?s high-heat environment, starters take in a lot of damaging heat that destroys the windings of the starter and solenoid. To combat this problem, we offer a non-conductive strap-on heat shield with a highly-reflective...

Sometimes after installing a new sound system, you may experience some bothersome engine/alternator noise, typically characterized by a whine that increases in pitch with engine speed. Though this is usually caused by a poor...

Now you can turn any modern style battery into a vintage looking one by adding this battery topper featuring the correct special grain just as original. Battery toppers are designed to be used with any maintenance free flat...

Add an under trunk or hood lamp to your classic with this universal lamp set. Includes bracket, bulb, internal switch and wiring to install.

This safety feature is a must have for any electric fuel-pump fed Muscle Car. If your motor stalls and your float is sticking, or worse, if you're in an accident severe enough to stop the motor, your electric fuel pump will...

This weatherproof Fan-Thom II kit comes with a threaded thermostat that screws into the engine block or intake manifold for a professional looking installation. This is inexpensive protection for an electric fan and a...

OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. Note: For a money saving set of 10 use...

Starter Cable Boot for 1954-1960 Oldsmobile 88, Dynamic, Super, Fiesta and 98 models, Also 1932-1953 Buick models and other various 1954-1972 GM models as required.

The DEI Cell Saver Battery insulation kit is designed to solve the problem of heat soak into batteries preventing premature failure due to heat. Batteries are very susceptible to heat and vibration that could cause premature...

Install extra driving or fog lights easily with this set. Set includes: Lighted switch Switch base Wiring harness Mounting hardware 30 amp relay Connectors Switch can be wired to turn lights on per state law requirements:...

Correct replacement voltage regulator washer head bolts used on various GM vehicles fron 1969-1972. Note: For 1/2" hole well nut with captive brass inserts. use A13010K. Correct hardware can make any installation job...

Correct replacement battery tray bolts used on various GM vehicles 1964 and newer. 1/2" hex with flat tip with 1-1/8" free spinning conical washer. Black phosphate coated. Correct hardware can make any installation job...

Correct replacement voltage regulator serrated washer head shoulder bolts used on various GM vehicles fron 1963-1968. Note: For 3/8" hole well nut with captive brass inserts. use A16240K. Correct hardware can make any...

Correct replacement voltage regulator well nuts used on various GM vehicles. 10-24, fits 3/8" hole. Neoprene with captive brass nut. Note: For a money saving set of 3 use A16240K. Correct hardware can make any installation...

Replacement fuse block screws used on various GM vehicles. Black phosphate with wax sealer. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions....

Correct style external tooth lock washers used on various GM vehicles. Zinc plated. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part...

EFI Wiring Harness 2006-12 GM LS2/LS3/LS7 This harness is designed for use on any 2006-12 LS2, LS3, LS7, or LS99 with throttle by wire. It uses the factory ECM & TCM and will operate engines with or without varible valve...

Turn your electric fan on at whatever your desired temperature is with this adjustable temperature sensor. The sensor adjusts from 180°F to 240°F and helps prevent overheating in performance vehicles when driving at...

Billet Style Illuminated Console-Mount 2 Switch Kit

Nu-Relics Power Windows S- Boots door wiring conduit. These boots install between the jamb and the door to protect the wiring and seal out the elements. Can be used in vehicles 1958 and up. Sold in pairs.

Universal replacement headlight pigtail wiring harness for vehicles with 3-prong H4/9003 halogen headlamp bulbs. The original socket assemblies are often missing, cracked or brittle on classic cars. This replacement, heavy...

Reproduction tie strap used on various late model GM vehicles to secure the wiring harnesses within the engine compartment. Can be used on any vehicle by simply drilling a standard 1/4" hole. Correct hardware can make any...

Reproduction "T" clip used on various late model vehicles to secure the wiring harnesses within the engine compartment. Can be used on any vehicle by simply drilling a standard 1/4" hole. Correct hardware can make any...

Reproduction of the hard-to-find switch to replace original inoperative headlamp switch on 1976-78 Chevette. This reproduction switch will fit exactly as original and is designed as a service replacement for original GM part...

Universal fit headlamp switch for a wide variety of vehicle applications from the 1940's and beyond. Each switch features 3 position push/pull functionality with knob and shaft. Required a 3/8 diameter hole for mounting, and...

Single male fan pigtail connector for Northern or SPAL single fans. Required when not using Northern relay harness. Note: This same pigtail is included on Northern relay harnesses. Use part# 40080 for Northern relay...

This Painless Performance modular blank fuse block can be used on any vehicle where additional circuits are needed. The four circuit ATO fuse center works great for in-line wiring applications, such as trailer wiring or when...

For alternators that produce up to 100 AMPS, this add-on kit provides heavier gauge wiring with connectors to complete the high output alternator installation process quickly, easily and safely.

Single contact pigtail with with 1 wire. For use with lamps 63, 67, 87, 89, 93, 97, 209, 1003, 1073, 1129, 1133, 1141 & 1156.

DEI Easy Loom split wire sleeve installation tool for 8-11mm lines.

This set allows you to position the starter solenoid any place you need to in order to make maintenance easier, clean up an inner fender or just replace a factory starting circuit. Set includes: Starter solenoid Wire ha...

This set allows you to position the starter solenoid any place you need to in order to make maintenance easier, clean up an inner fender or just replace a factory starting circuit. Set includes: Starter solenoid Wire ha...

Correct style external tooth lock washers used on various GM vehicles. Zinc plated. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part...

Correct style external tooth lock washers used on various GM vehicles. Zinc plated. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part...

This hose bracket is designed to secure a pair of hoses to the body or frame to prevent damage of the hoses and keep the engine compartment neat and tidy in appearance.

This universal ignition switch panel is a great solution for hot rods, race cars, or customized muscle cars. Polished aluminum panel. Toggle switch with cover ? 25 amps at 12 volts. Toggle switch without cover ? 25 amps at...

This Painless Performance wiring fuse block four circuit add-on is a universal fit. The component includes the fue block and the terminals. It weighs one pound and ships via UPS.

This eight block add-on electrical fuse block is a universal fit. The fuse block and the terminals comprise the kit. It weighs four ounces and ships via UPS.

Polarity reversing module for power windows, door locks, or actuators. This module is designed to reverse the polarity on modern power window motors, door locks, or linear actuators. It will enable the use of stock-type...

Correct style external tooth lock washers used on various GM vehicles. Zinc plated. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part...

Correct style external tooth lock washers used on various GM vehicles. Zinc plated. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part...

Correct style external tooth lock washers used on various GM vehicles. Zinc plated. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part...

This set is designed to allow a wide range of temperature adjustments for your electric fan. A bulb at the top of the capillary tube is designed to probe or be attached to the top or hottest portion of the radiator. The...

This Fan-Thom II kit comes with a threaded thermostat that screws into the engine block or intake manifold for a professional looking installation. This is inexpensive protection for an electric fan and a vehicle's wire...

This is a replacement switch for use with the Painless Fan-Thom II electric fan relay set. Made in USA Includes: 195° F on / 185° F off thermostat 1/2" NPT to 3/8" NPT adapter Insulated terminals

This is a replacement switch for use with the Painless Fan-Thom II electric fan relay set. Made in USA Includes: 185° F on / 175° F off thermostat 1/2" NPT to 3/8" NPT adapter Insulated terminals

This set, complete with a 250 amp solenoid, will effectively handle alternator feedback of the highest amperage alternators. Eliminates engine run-on when the master disconnect is turned off. Alternator feedback can keep your...

This set, complete with a 250 amp solenoid, will effectively handle alternator feedback of the highest amperage alternators. Eliminates engine run-on when the master disconnect is turned off. Alternator feedback can keep your...

This is inexpensive protection for an electric fan and a vehicle's wire harness. Provides constant voltage, protects from voltage and amperage spikes and prevents the fan from back feeding voltage through the vehicle's wire...

When you need protection from the harsh conditions, this set provides complete protection from the elements to ensure reliable and dependable performance. This is inexpensive protection for an electric fan and a vehicle's...

Mounts in 5/16" hole. 12 Volt operation. Made in USA

Designed specifically to prevent voltage drops at the fuel pump to maintain constant fuel pump pressure and to prevent fuel pump amperage overloads from damaging the vehicle's electrical system. Set includes: 30 amp heavy...

It's a good idea to relay your fuel pump for the street and a must when you're racing. Designed specifically to prevent voltage drops at the fuel pump to maintain constant fuel pump pressure and to prevent fuel pump amperage...

When upgrading tail lights to the newer high wattage halogens, always use a relay. This set gives you everything you need to protect your wiring and switches. Made in USA

This set is designed to allow a wide range of temperature adjustments for your electric fan. A bulb at the top of the capillary tube is designed to probe or be attached to the top or hottest portion of the radiator. The...