1969-74 Chrysler 8-3/4" With 1-7/8 Pinion Stem Master Bearing Set
Yukon master overhaul kit for Chrysler 8.75" rear ends. Included in this kit are Timken carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, oil...
1969-74 Chrysler 8-3/4" With 1-7/8 Pinion Stem Master Bearing Set
Classic $322.99 set
Mopar 8-3/4" Differential Cast Iron 10-Spline Rear Yoke (Uses 7260 Series Strap Retained U-Joint)
This cast iron yoke is manufactured specifically for Mopar differentials. Includes the yoke, and mounting hardware. Important: Use MM3311 s trap kit, Note: Uses 7260 series U-joint (sold separately) that have a 2.125"...
Mopar 8-3/4" Differential Cast Iron 10-Spline Rear Yoke (Uses 7260 Series Strap Retained U-Joint)
Classic $210.99 ea
8-3/4" Adjustable Pinion Snubber
If you are using your stock leaf spring rear suspension and you have added horsepower to your engine; then you need to add an adjustable pinion snubber. This helps control axle windup by adjusting the height to the floor pan....
Mopar - Yukon Strap Kit - With 7260 U-Joint
These u-joint strap kits are designed for use on stock and Yukon pinion yokes with 7260 u-joint size. Includes: two straps and four bolts. Made in the USA.
Mopar - 8.3/4" "89" Rear Differential Crush Sleeve For 1.7/8" Pinion
Mopar 8-3/4" "89" case housing
Mopar - 8.3/4" "89" Rear Differential Crush Sleeve For 1.7/8" Pinion
Classic $18.99 ea
Mopar - 8-3/4" Or 9-1/4" With "41" Or "89" Rear Differential - Pinion Seal
Mopar 8-3/4" or 9-1/4" with "41" or "89" case housing
Mopar - 8-3/4" Or 9-1/4" With "41" Or "89" Rear Differential - Pinion Seal
Classic $13.99 ea
Dana 60 Chrome Hex Head Differential Cover Bolt Set
This set is for use on Dana 60, or any other rear end using 3/8"-16 x 3/4" bolts. Includes 12 chrome finished bolts and 12 Flat washers (not chromed).
This locking pawl and flanged nut is used on the right side axle of 8-3/4" and 9-3/4" differentials. The pawl secures the axle end play adjusting nut once proper bearing play is established.
Mopar 8-3/4" (Coarse Spline) Pinion Nut Washer
This pinion nut washer is for the Mopar 8-3/4" 10 spline pinion. FITS: Mopar 8-3/4", 41 Case Housing Mopar 8-3/4", 42 Case Housing Mopar 8-3/4", 89 Case Housing
1960-76 Mopar Rear End Housing E-Brake and Brake Line Clip Set
Reproduction rear and housing e-brake, and brake line clip set for all 1960-76 models. Replace your rusted originals with these correct replacements. Must be welded to the factory locations.
1960-69 Chrysler 8-3/4" With 1-3/4 Pinion Stem Master Bearing Set
Yukon master overhaul kit for Chrysler 8.75" rear ends. Included in this kit are Timken carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, oil...
1960-69 Chrysler 8-3/4" With 1-3/4 Pinion Stem Master Bearing Set
Classic $458.99 set
Mopar 8-3/4" Differential Billet Steel 10-Spline Rear Yoke (Uses 1350 Series U-Bol Retained U-Joint)
This billet steel yoke is manufactured specifically for Mopar differentials. Includes the yoke, and mounting hardware. Important: Use MM3307 u-bolt kit, Note: Uses 1350 series U-joint (sold separately) that have a...
Mopar 8-3/4" Differential Billet Steel 10-Spline Rear Yoke (Uses 1350 Series U-Bol Retained U-Joint)
Classic $381.99 ea
1960-72 Chrysler 8-3/4" With 1-3/8 Pinion Stem Master Bearing Set
Yukon master overhaul kit for Chrysler 8.75" rear ends. Included in this kit are Timken carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, oil baffles and...
1960-72 Chrysler 8-3/4" With 1-3/8 Pinion Stem Master Bearing Set
Classic $366.99 set
Mopar 8-3/4" Differential Forged Steel 10-Spline Rear Yoke (Uses 1350 Series Strap Retained U-Joint)
This forged steel yoke is manufactured specifically for Mopar differentials. Includes the yoke, and mounting hardware. Important: Use MM3310 strap kit, Note: Uses 1350 series U-joint (sold separately) that have a...
Mopar 8-3/4" Differential Forged Steel 10-Spline Rear Yoke (Uses 1350 Series Strap Retained U-Joint)
Classic $199.99 ea
Mopar 8-3/4" Differential Billet Steel 29-Spline Rear Yoke (Uses 1350 Series U-Bol Retained U-Joint)
This billet steel yoke is manufactured specifically for Mopar differentials. Includes the yoke, and mounting hardware. Important: Use MM3307 u-bolt kit, Note: Uses 1350 series U-joint (sold separately) that have a...
Mopar 8-3/4" Differential Billet Steel 29-Spline Rear Yoke (Uses 1350 Series U-Bol Retained U-Joint)
Classic $198.99 ea
8-1/4" Master Bearingset With Timken Bearings
Motive Gear master bearing overhaul set for Chrysler 8.25" rear ends. Included in this set are Timken carrier bearings and races, pinion bearings and races, pinion seal, complete shims, ring gear bolts, pinion nut, crush...
Filtermag; Rear Differential Filter Magnet
FilterMag powerful rare-earth magnet traps and holds wear inducing metal particles smaller than 40-microns down to 1-micron. The super-strong magnetic force holds FilterMag to the cover, is reusable and will reduce...
Mopar - Yukon U-Bolt Kit (W/ 1310 U-Joint) - 2 U-Bolts (3/8" X 1-11/16") & 4 Nuts
These u-joint u-bolt kits are designed for use on stock and Yukon pinion yokes with 1310 u-joint size. Includes: two u-bolts (3/8" X 1-11/16") and four nuts. Made in the USA.
Mopar - Yukon U-Bolt Kit (W/ 1310 U-Joint) - 2 U-Bolts (3/8" X 1-11/16") & 4 Nuts
Classic $27.99 set
5/16"-18 X 3/4" ARP Stainless Steel Differential Cover Bolt Set
Enhance the appearance of your rear end with ARP's stainless steel rear cover bolts. These bolts add a lustrous contrast to a painted OEM cover, compliment a chrome plated aftermarket version or add flash to that cast...
Differential Pinion Thrust Spacer Set
Replacement thrust spacer set for 8-3/4" differentials with clutch type Sure-Grip prior to 1970. Required to provide axle thrust surface in four-spider differential applications. One set required per vehicle.