Product#: MM2268

1947-1992; Emblem Installation Barrel Nut; For 3/16 inch Stud; Fits 7/32 inch Hole Diameter; Each

This is the nut needed to allow you to install all emblems for the fenders, header panel and trunk lid, etc. The barrel nut is a push on style versus the original twist on, which will not require removal of body panels for...

Product#: *MM2267K

Barrel Nut, Fits 1/8" Emblem Stud, Fits 5/32" Hole, Spring Steel, Phosphate Coated, 10 Piece Set

Replacement barrel nuts used on various GM vehicles. The barrel nut is a push on style versus the original thread cutting pal nut, which will not require the removal of body panels for emblem installation. Simply install each...

Product#: *A2100K

Push On Flat Nut, Fits 3/32" Stud, Black Phosphate Coated, 10 Piece Set

Replacement push on flat nuts used on various vehicles. Black phosphate coated. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is...

Product#: *A2896K

Thread Cutting Pal Nut, 3/16" Stud Size, Hex Washer Head, Zinc Plated

Replacement thread cutting pal-nuts used on various GM vehicles. Hex washer head, zinc plated. Mastic sealer washers sold separately. Correct hardware can make any installation job easier. Replace your missing or damaged...

Product#: *A10733K

Thread Cutting Pal Nut, 5/16" Stud Size, Hex Washer Head, Zinc Plated, 10 Piece Set

Replacement thread cutting pal-nuts used on various GM vehicles. Hex washer head, zinc plated. Mastic sealer washers sold separately. Correct hardware can make any installation job easier. Replace your missing or damaged...

Product#: *WA300K

Round Push On Flat Nut, Fits 5/32" Stud Size, Zinc Plated, 10 Piece Set

Replacement push on round flat nuts used on various vehicles. Zinc plated. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is...

Product#: *A3405K

Thread Cutting Pal Nut, 1/4" Stud Size, Hex Washer Head, Zinc Plated, 10 Piece Set

Replacement thread cutting pal-nuts used on various GM vehicles. Hex washer head, zinc plated. Mastic sealer washers sold separately. Correct hardware can make any installation job easier. Replace your missing or damaged...

Product#: *R404

Speed Nut for 3/16" Stud - Self Threading - 8 Piece Set; with Rubber Pad

OER®speed nut designed for use with various original and reproduction emblem mounting studs that have a 3/16" stud. This speed nut can be applied to virtually any emblem or product that has a 3/16" stud and pressed into...

Product#: A13964

Universal Emblem Barrel Nut Kit, fits 1/8" Stud, fits 11/64" Hole; 10 Piece Set

Replacement barrel nuts used on various GM vehicles. The barrel nut or tubular nut is a push on style versus the original thread cutting pal nut, which will not require the removal of body panels for emblem installation....

Product#: *R406

Speed Nut 1/4" Self Threading Nut Retainer Set - Set of 6

Speed nuts are a great way of installing parts with studs onto the vehicle. These speed nuts are applied to the stud and pushed into the hole. The part is held in place by the self threading nut. 6 piece speed nut set is...

Product#: *11293K

Barrel Nut; Fits 1/8" Emblem Stud; Fits 3/16" Hole; Spring Steel; Black Phosphate Finish; 10 Piece Set

Replacement barrel nuts used on various GM vehicles. The barrel nut is a push on style versus the original thread cutting pal nut, which will not require the removal of body panels for emblem installation. Simply install each...

Product#: *5195K

Barrel Nut, Fits 1/8" Emblem Stud, Fits 1/4" Hole, Spring Steel, Phosphate Coated, 10 Piece Set

Replacement barrel nuts used on various GM vehicles. The barrel nut is a push on style versus the original thread cutting pal nut, which will not require the removal of body panels for emblem installation. Simply install each...

Product#: *11501047K

Thread Cutting Pal Nut Set; with Sealer, 3/16" Stud Size, Hex Washer Head, Zinc Plated, 10 Piece Set

Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is original equipment for multiple GM applications, it can be used for other...

Product#: *A2098K

Push On Flat Nut, Fits 1/16" Stud, Black Phosphate Coated, 10 Piece Set

Replacement push on flat nuts used on various vehicles. Black phosphate coated. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is...

Product#: *A8855K

Thread Cutting Pal Nut, 5/32" Stud Size, Hex Washer Head, Zinc Plated, 10 Piece Set

Replacement thread cutting pal-nuts used on various GM vehicles. Hex washer head, zinc plated. Mastic sealer washers sold separately. Correct hardware can make any installation job easier. Replace your missing or damaged...

Product#: *8545K

Barrel Nut, Fits 5/32" Stud, Fits 7/32" Hole, Spring Steel, Phosphate Coated, 10 Piece Set

Replacement barrel nuts used on various GM vehicles. The barrel nut is a push on style versus the original thread cutting pal nut, which will not require the removal of body panels for emblem installation. Simply install each...

Product#: A3404

Speed Nut 3/16" Self Thread Cutting - Small Washer - Each

OER®speed nut designed for use with various original and reproduction emblem mounting studs that have a 3/16" stud. This speed nut can be applied to virtually any emblem or part that has a 3/16" stud and pressed into the...

Product#: *11502547K

Thread Cutting Pal Nut Set; with Sealer, 1/8" Stud Size, Hex Washer Head, Zinc Plated, 10 Piece Set

Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is original equipment for multiple GM applications, it can be used for other...

Product#: *A2102K

Push On Flat Nut, Fits 5/32" Stud, Black Phosphate Coated, 10 Piece Set

Replacement push on flat nuts used on various vehicles. Black phosphate coated. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is...

Product#: 11502547

Thread Cutting Pal Nut With Sealer, 1/8" Stud Size, Hex Washer Head, Zinc Plated

OER® thread cutting pal nut with sealer is designed for use with various original and reproduction emblem mounting studs that have a 1/8" stud. This speed nut can be applied to virtually any emblem or product that has a...

Product#: *A3400K

Thread Cutting Nut, 1/8" Stud Size, 1/4" Hex, 10 Piece Set

Replacement thread cutting pal-nuts used on various GM vehicles. Hex head, zinc plated. Mastic sealer washers sold separately. Correct hardware can make any installation job easier. Replace your missing or damaged hardware...

Product#: *A3138K

Push On Flat Nut, Fits5/16" Stud, Black Phosphate Coated, 10 Piece Set

Replacement push on flat nuts used on various vehicles. Black phosphate coated. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is...

Product#: *A2103K

Push On Flat Nut, Fits 3/16" Stud, Black Phosphate Coated, 10 Piece Set

Replacement push on flat nuts used on various vehicles. Black phosphate coated. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is...

Product#: *A3401K

Thread Cutting Nut, 1/8" Stud Size, 5/16" Hex, 10 Piece Set

Replacement thread cutting pal-nuts used on various vehicles. Hex head, zinc plated. Mastic sealer washers sold separately. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with...

Product#: *A2099K

Push On Flat Nut, Fits 1/8" Stud, Black Phosphate Coated, 10 Piece Set

Replacement push on flat nuts used on various vehicles. Black phosphate coated. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is...

Product#: MM2267

Barrel Nut, Fits 1/8" Emblem Stud, Fits 5/32" Hole, Spring Steel, Black Phosphate Coated

Replacement barrel nuts used on various GM vehicles. The barrel nut is a push on style versus the original thread cutting pal nut, which will not require the removal of body panels for emblem installation. Simply install each...

Product#: 11293

Barrel Nut; Fits 1/8" Emblem Stud; Fits 3/16" Hole; Spring Steel; Black Phosphate Coated

Replacement barrel nuts used on various GM vehicles. The barrel nut is a push on style versus the original thread cutting pal nut, which will not require the removal of body panels for emblem installation. Simply install each...

Product#: A2098

Push On Flat Nut, Fits 1/16" Stud, Black Phosphate Coated

Replacement push on flat nuts used on various vehicles. Black phosphate coated. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is...

Product#: A10733

Thread Cutting Pal Nut, 5/16" Stud Size, Hex Washer Head, Zinc Plated

Replacement thread cutting pal-nuts used on various GM vehicles. Hex washer head, zinc plated. Mastic sealer washers sold separately. Correct hardware can make any installation job easier. Replace your missing or damaged...

Product#: A2100

Push On Flat Nut, Fits 3/32" Stud, Black Phosphate Coated

Replacement push on flat nuts used on various vehicles. Black phosphate coated. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is...

Product#: A2102

Push On Flat Nut, Fits 5/32" Stud, Black Phosphate Coated

Replacement push on flat nuts used on various vehicles. Black phosphate coated. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is...

Product#: B11245K

Mastic Sealer Washers, 7/16" Diameter, Seals Pal Nuts And Clip Nuts to Body Panel, 25 Piece Set

Replacement mastic sealer washers used to seal emblem studs and molding clips to the body on various GM vehicles. Use with molding nuts and thread cutting nuts. 25 piece set. Correct hardware can make any installation job...

Product#: B11280K

Mastic Sealer Washers, 1-3/4" Diameter, Seals Pal Nuts And Clip Nuts to Body Panel, 4 Piece Set

Replacement mastic sealer washers used to seal emblem studs and molding clips to the body on various GM vehicles. Use with molding nuts and thread cutting nuts. 4 piece set. Correct hardware can make any installation job...

Product#: *R408

Speed Nut 1/4" Self Thread Cutting - 12 Piece Set

Speed nuts are a great way of installing parts with studs onto the vehicle. These speed nuts are applied to the stud and pushed into the hole. The part is held in place by the self threading nut. 12 piece speed nut set is...

Product#: *R401

Speed Nut for 1/8" Stud - Self Threading - 8 Piece Set - with Rubber Pad

OER®speed nut designed for use with various original and reproduction emblem mounting studs that have a 1/8" stud. This speed nut can be applied to virtually any emblem or product that has a 1/8" stud and pressed into the...

Product#: *R403

Speed Nut for 3/16" Stud - Self Threading - with Rubber Pad; 4 Piece Set

OER®speed nut designed for use with various original and reproduction emblem mounting studs that have a 3/16" stud. This speed nut can be applied to virtually any emblem or product that has a 3/16" stud and pressed into...

Product#: 8545

Barrel Nut, Fits 5/32" Emblem Stud, Fits 7/32" Hole, Spring Steel, Black Phosphate Coated

Replacement barrel nuts used on various GM vehicles. The barrel nut is a push on style versus the original thread cutting pal nut, which will not require the removal of body panels for emblem installation. Simply install each...

Product#: *R402

Speed Nut for 1/8" Stud - Self Threading - 4 Piece Set; with Rubber Pad

OER®speed nut designed for use with various original and reproduction emblem mounting studs that have a 1/8" stud. This speed nut can be applied to virtually any emblem or product that has a 1/8" stud and pressed into the...

Product#: K424

Universal Emblem & Trim Installation Speed Nut Set ; 5/16" ; 8 Piece Set

Keep your emblems and side marker bezels securely mounted with this speed nut set designed for applications using 5/16" mounting studs. These versatile fasteners are ideal for a variety of original and reproduction emblems,...

Product#: WA300

Round Push On Flat Nut, Fits 5/32" Stud Size, Zinc Plated

Replacement push on round flat nuts used on various vehicles. Zinc plated. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is...

Product#: 11501047

1930-2007 GM; Thread Cutting Pal Nut with Sealer; 3/16" Stud Size; Hex Washer Head; Zinc Plated

OER®thread cutting pal nut with sealer is designed for use with various original and reproduction emblem mounting studs that have a 3/16" stud. This speed nut can be applied to virtually any emblem or product that has a...

Product#: K423

Universal Emblem & Trim Installation Speed Nut Set ; 5/16" ; 4 Piece Set

Keep your emblems and side marker bezels securely mounted with this speed nut set designed for applications using 5/16" mounting studs. These versatile fasteners are ideal for a variety of original and reproduction emblems,...

Product#: 5195

Barrel Nut, Fits 1/8" Emblem Stud, Fits 1/4" Hole, Spring Steel, Black Phosphate Coated

Replacement barrel nuts used on various GM vehicles. The barrel nut is a push on style versus the original thread cutting pal nut, which will not require the removal of body panels for emblem installation. Simply install each...

Product#: A6021

1/8" Flanged Acorn Thread Cutting Capped Palnut w/ Mastic Sealer

Stamped steel 1/8" flanged pal nut used by multiple makes on various models. These self threading domed nuts were originally used to attach emblems, molding, and trim items. It features a period correct zinc coating, cap/dome...

Product#: K13063

Tubular Barrel Nut Retainer Clip; For Emblem Installation; For 3/32" Stud; Fits 1/8" Diameter Hole in Panel

Specialty barrel nut designed to install emblems on the body. Can be used for fender emblems, quarter panel emblems, and other body emblems. The barrel nut makes installation of emblems easy. Simply put the barrel nut onto...

Product#: A6023

10-24 Stamped Acorn Palnut; Gold/Yellow Zinc

Stamped steel 10-24 thread palnut used by multiple makes on various models. These self threading domed nuts were originally used to attach emblems, molding, and trim items. It features a period correct yellow zinc coating and...

Product#: NT400

Speed Nut; 4 mm

Speed nut designed for use with various original and reproduction emblem mounting studs that have a 4mm stud. This speed nut can be applied to virtually any emblem or product that has a 4mm stud and pressed into the hole for...

Product#: A3401

Thread Cutting Nut, 1/8" Stud Size, 5/16" Hex

Replacement thread cutting pal-nuts used on various vehicles. Hex head, zinc plated. Mastic sealer washers sold separately. Used to install 1972 "DODGE" Charger grill emblem. Correct hardware can make any installation job...

Product#: A2426

Push-on Flat Nut; Fits 3/16" Stud Size; Measures 3/8" x 5/8"

Universal flat push-on clip used for variuos applications with a 3/16" stud. Clip measures 3/8" x 5/8" and has a black phosphate finish.

Product#: A6022

8-32 Flanged Stamped Acorn Capped Machine Thread Nut w/o Mastic Sealer

Stamped steel 8-32 flanged machine thread nut used by multiple makes on various models. These self threading domed nuts were originally used to attach emblems, molding, and trim items. It features a period correct zinc...

Product#: K18249

1/8 Stud 5/32 Hole Barrel Clip

Product#: J222

OER Logo With Tag Decal

Product#: 22729684

Supercharged Emblem; Rectangular; 4.3" x 0.7"; Each;

Reproduction SUPERCHARGED emblem for various applications. Peel-and-stick application allows you to use this emblem in almost any location on any vehicle. Measures 4.3" long x 0.7" wide. Sold individually.

Product#: *EM9684Z

Supercharged Emblem; Rectangular; 4.3" x 0.7"; Set of 3

Reproduction SUPERCHARGED emblem set for various applications. Peel-and-stick application allows you to use this emblem in almost any location on any vehicle. Measures 4.3" long x 0.7" wide. Sold as a set of 3 emblems.

Product#: MM3

Magnetic Sign; Look And Enjoy...But Please Don't Touch!

Make sure people know to "Look And Enjoy...But Please Don't Touch!" with this small but effective magnet.

Product#: CP10A

4" X 1-1/2" Classic Industries Decal

When it comes to quality products, Classic Industries® can't be beat! Our new full color decals can be applied to virtually any clean surface.

Product#: ME00434

Polished Stainless Steel "454" Fender Engine cid Callout Emblems; Flat Panel

Morris Classic Concepts flat polished stainless steel engine cubic inch callout emblems will adhere to most any flat surface. Engine size emblems are laser cut in the factory font from 0.09" thick mirror-polished stainless...

Product#: ME00540

Polished Stainless Steel "540" Fender Engine cid Callout Emblems; Flat Panel

Morris Classic Concepts flat polished stainless steel engine cubic inch callout emblems will adhere to most any flat surface. Engine size emblems are laser cut in the factory font from 0.09" thick mirror-polished stainless...

Product#: ME00396

Polished Stainless Steel "397" Fender Engine cid Callout Emblems; Flat Panel

Morris Classic Concepts flat polished stainless steel engine cubic inch callout emblems will adhere to most any flat surface. Engine size emblems are laser cut in the factory font from 0.09" thick mirror-polished stainless...

Product#: CP10B

8-1/2" x 4" Classic Industries Decal

When it comes to quality products, Classic Industries® can't be beat! Our new full color decals can be applied to virtually any clean surface.