Mallory; Distributor Points; Standard
Ignition points for all 23, 24, 25 26 and 27 series Mallory breaker point distributors.
Accel; 1955-74; Chrome; 42,000 Volt; 1.4 Ohm Primary; Superstock Ignition Coil; Points
Replace your stock coil with an Accel high performance coil for increased performance, longer life and maximum dependability. Fits 1955-74 with breaker point ignition
Accel; 1955-74; Chrome; 42,000 Volt; 1.4 Ohm Primary; Superstock Ignition Coil; Points
Classic $53.99 ea
1975-82 GM; Ignition Wire Grommet; 4 Hole; With Slits
Reproduction 4-hole igniton wire grommet for various 1975-82 Buick, Chevrolet, Pontiac, and Oldsmobile models. Features convenient slits so it can be installed on each plug wire without removing or replacing the wire end. Can...
Dress your engine with this all chrome coil cover. Fits most early model coils. Includes cover and attaching bracket. For use with small block engines.
4 Piece 6" x 1-1/2" Spark Plug Wire Heat Shield Set
This heat shield set offers spark plug wires and boots the ultimate protection from conductive and radiant heat. The dual purpose sleeving has an aluminized outer surface that reflects 90% of radiant heat, up to 2000° F,...
Mallory; Distributor Cap; For 23, 24, 25, 26, 27 And 37 Series Distributors
Replacement distributor cap for Mallory Unilite distributors. Fits 23, 24, 25, 26, 27 and 37 Series. Mallory Heavy-Duty cap is constructed of top quality material and designed to fit your application for long lasting...
Mallory; Distributor Cap; For 23, 24, 25, 26, 27 And 37 Series Distributors
Classic $41.99 ea
Vacuum Advance Cover; Chrome Plated Steel
Chrome plated steel cover that slides over factory vacuum advance units. Attaches with double sided tape. Fits most classic vaccum advance distributors.
Black 4 Piece Cool-It Plug Wire Sleeve Set
These dual-purpose sleeves enhance performance, reduce misfires, extend plug wire life and will not react with petroleum products. The double-wall construction keeps the wire and boot cooler in a high-temperature engine. It's...
Red 4 Piece Cool-It Plug Wire Sleeve Set
These dual-purpose sleeves enhance performance, reduce misfires, extend plug wire life and will not react with petroleum products. The double-wall construction keeps the wire and boot cooler in a high-temperature engine. It's...
2 Piece 6" x 1-1/2" Spark Plug Wire Heat Shield Set
This heat shield set offers spark plug wires and boots the ultimate protection from conductive and radiant heat. The dual purpose sleeving has an aluminized outer surface that reflects 90% of radiant heat, up to 2000° F,...
Natural 4 Piece Cool-It Plug Wire Sleeve Set
These dual-purpose sleeves enhance performance, reduce misfires, extend plug wire life and will not react with petroleum products. The double-wall construction keeps the wire and boot cooler in a high-temperature engine. It's...
Red 6 Piece Cool-It Plug Wire Sleeve Set
These dual-purpose sleeves enhance performance, reduce misfires, extend plug wire life and will not react with petroleum products. The double-wall construction keeps the wire and boot cooler in a high-temperature engine. It's...
Blue 4 Piece Cool-It Plug Wire Sleeve Set
These dual-purpose sleeves enhance performance, reduce misfires, extend plug wire life and will not react with petroleum products. The double-wall construction keeps the wire and boot cooler in a high-temperature engine. It's...
Silver 6 Piece Cool-It Plug Wire Sleeve Set
These dual-purpose sleeves enhance performance, reduce misfires, extend plug wire life and will not react with petroleum products. The double-wall construction keeps the wire and boot cooler in a high-temperature engine. It's...
Black 6 Piece Cool-It Plug Wire Sleeve Set
These dual-purpose sleeves enhance performance, reduce misfires, extend plug wire life and will not react with petroleum products. The double-wall construction keeps the wire and boot cooler in a high-temperature engine. It's...
Blue 6 Piece Cool-It Plug Wire Sleeve Set
These dual-purpose sleeves enhance performance, reduce misfires, extend plug wire life and will not react with petroleum products. The double-wall construction keeps the wire and boot cooler in a high-temperature engine. It's...
Spark Plug Deluxe Wire Separator Set; Blue
This set of spark plug wire separators is made from high grade plastic which helps insulate the plug wires and reduce shorts and crosstalk. Includes two 4-wire separators, two 3-wire separators, and two 2-wire separators
Chrome 4 Hole 5-1/4" High Lift Wire Looms - Pair
Beautifully chromed, heavy gauge steel with easy snap in grommets eliminates the need for removing wires for quick installation. Sold as a pair.
Alter Ego 812 Series; Insulated Billet Aluminum Line Clamp; 4 Hole/Separator; 3/16" to 3/8"
Alter Ego 812 Series insulated billet aluminum line clamp/separator with Delrin inserts. These clamps are great for cleaning up your engine bay. Safe for use with most hard and soft fluid and air lines. Perfect for custom...
1961-73 Mopar 361, 383, 400, 413 Single Point Standard Ignition Remanufactured Distributor
If your classic is having problems starting, has a rough idle or the performance is not what it use to be, it could be time to change your distributor. Each distributor is remanufactured and tested to guarantee you get the...
1961-73 Mopar 361, 383, 400, 413 Single Point Standard Ignition Remanufactured Distributor
Classic $139.99 ea
Blue 6-Piece Taylor Clamp-Style 10.4MM Wire Separator Set
Organize your engine bay with Taylor clamp style wire separators. Manufactured from non-conductive type 6/6 nylon that won't melt, distort, fade or crack. Each six piece set includes two 4 wire separators, two 3 wire...
MSD; Blaster 3 Series; 45,000 Volt Ignition Coil; Extra Tall Tower; Red
If you are looking to upgrade your stock coil or want to complement the performance of your MSD 5, 6 and 7 Series Ignition, our Blaster Coils are the right choice. The Blaster 3 Coil shares the same special windings and high...
MSD; Blaster 3 Series; 45,000 Volt Ignition Coil; Extra Tall Tower; Red
Classic $66.99 ea
4 Piece Thermo-Flex Plug Wire Heat Shield Set
Thermo-Flex Plug Wire Heat Shield is manufactured with a combination of materials to provide thermal insulation and radiant heat protection. Thermo-Flex Plug Wire Heat Shields can withstand extreme temperatures up to...
Blue 6 Piece Taylor Clamp-Style 7-8.2 MM Wire Separator Set
Organize your engine bay with Taylor clamp style wire separators. Manufactured from non-conductive type 6/6 nylon that won't melt, distort, fade or crack. Each six piece set includes two 4 wire separators, two 3 wire...
MSD Spark Plug Boot & Terminal - Silicon 90&Deg; (Pair)
These boots are designed with longevity in mind. Each boot provides excellent resistance as well as maximum protection against spark loss.
Red 6 Piece Taylor Clamp-Style 7-8.2 MM Wire Separator Set
Organize your engine bay with Taylor clamp style wire separators. Manufactured from non-conductive type 6/6 nylon that won't melt, distort, fade or crack. Each six piece set includes two 4 wire separators, two 3 wire...
Black 6 Piece Taylor Clamp-Style 7-8.2 MM Wire Separator Set
Organize your engine bay with Taylor clamp style wire separators. Manufactured from non-conductive type 6/6 nylon that won't melt, distort, fade or crack. Each six piece set includes two 4 wire separators, two 3 wire...
Black 6-Piece Taylor Clamp-Style 10.4MM Wire Separator Set
Organize your engine bay with Taylor clamp style wire separators. Manufactured from non-conductive type 6/6 nylon that won't melt, distort, fade or crack. Each six piece set includes two 4 wire separators, two 3 wire...
Chrome 6 Piece Taylor Clamp-Style 7-8.2 MM Wire Separator Set
Organize your engine bay with Taylor clamp style wire separators. Manufactured from non-conductive type 6/6 nylon that won't melt, distort, fade or crack. Each six piece set includes two 4 wire separators, two 3 wire...
Spark Plug Gapper & Feeler Gauge Set
All-in-one tool comes with 6 spark plug gap wires, an electrode bending tool, and 12 steel blades. Precision wires and blades can measure both spark plug and ignition system settings. Blades are approximately 1/2" wide by 3...
MSD; Magnetic Pickup; Replacement For All MSD Billet Dististibutors
The MSD Magnetic Pick-Up replacement is the same high output assembly that is currently found in all MSD Distributors. It is supplied with the two pin connector installed. NOTE: No further discounts apply.
MSD; Magnetic Pickup; Replacement For All MSD Billet Dististibutors
Classic $49.99 ea
1972-85 Mopar Replacement Ignition Coil Ballast Resistor - With Electronic Ignition
Replacement Ballast Resistor for 1972-85 Mopar models with electronic ignition. The ballast resistor works in conjunction with the ignition coil. During low speed operation, the ballast resistor heats up. The increase in...
1972-85 Mopar Replacement Ignition Coil Ballast Resistor - With Electronic Ignition
Classic $7.99 ea
Mopar A, B & E-Body 8-Cylinder Distributor Cap
Standard quality replacement distributor cap for 1962-76 Mopar A, B & E-Body models with an 8-Cylinder engine.
1960-76 Chrysler, Plymouth, Dodge Small Block; Oil Pump Intermediate Shaft; Melling
Melling oil pump intermediate shaft also known as the distributor drive gear assembly. Fits all small block Mopar 273, 318, 340, or 360 engines. This is the drive shaft that drives the oil pump as well as the distributor off...
1960-76 Chrysler, Plymouth, Dodge Small Block; Oil Pump Intermediate Shaft; Melling
Classic $62.99 ea
Reproduction of the original vacuum advance unit for various 1962-79 Mopar Big Block engines. Fits 1962-72 Big Block engines with a single point distributor and 1971-79 Big Block engines with an electronic distributor....
1962-76 Mopar Distributor Rotor - 6 & 8-Cyl
Factory style replacement distributor rotor for 1962-76 Mopar 6 and 8-cylinder models. Sold individually. Applications: 1962-76 Mopar 6 & 8-Cylinder models without dual points 1973-76 Mopar 6 & 8-Cylinder models (all)
1960-76 Mopar V8; Pro Billet/Ready To Run Distributor Cap & Rotor Set; Red
Replacement cap and rotor set for Pro-Billet and Ready To Run Mopar V8 distributors. Applications: MN2519 MN2520 MN2521 MN2522
1960-76 Mopar V8; Pro Billet/Ready To Run Distributor Cap & Rotor Set; Red
Classic $12.99 set
340/440 6 Bbl Dual Point Distributor Leads
Dual point distributor leads with correct logo and original style terminal ends. Made from heat resistant wire with resistance welded D-ring terminal and has correct red sleeve for coil mounting.
Mopar A, B & E-Body Distributor Rotor Gold Quality
Professional Gold quality replacement distributor rotor for 1962-76 Mopar A, B & E-Body models.
Reproduction of the original vacuum advance unit for various 1962-79 Mopar Small Block engines. Fits 1962-72 Small Block engines with a single point distributor and 1971-79 Small Block engines with an electronic distributor....
1964-76 Mopar V8 Distributor Mounting Gasket
Reproduction distributor mounting gasket for various Mopar models. This gasket prevents moisture from entering the distributor shaft tube. Applications: 1964-65 413 CI Mopar Engines 1964-69 273 CI Mopar Engines 1964-71 383 &...
Mopar A, B & E-Body 8-Cylinder Gold Quality Distributor Cap
Professional Gold quality replacement distributor cap for 1962-76 Mopar A, B & E-Body models with an 8-Cylinder engine.
426 Hemi Dual Point Distributor Leads
Dual point distributor leads with correct logo and original style terminal ends. Made from heat resistant wire with resistance welded D-ring terminal and has correct red sleeve for coil mounting.
Mopar A, B & E-Body 6-Cylinder Gold Quality Distributor Cap
Gold quality replacement distributor cap for 1962-76 Mopar A, B & E-Body 6-Cylinder models.
Mopar Small Block Distributor Hold Down Clamp - Chrome
Protect yourself from unwanted timing changes! This replacement distributor hold down clamp prevents the distributor from turning in the intake manifold, ensuring correct timing under any condition. Each clamp set includes...
1961-73 Mopar 413, 426, 440 (Except High Performance) Single Point Remanufactured Distributor
If your classic is having problems starting, has a rough idle or the performance is not what it use to be, it could be time to change your distributor. Each distributor is remanufactured and tested to guarantee you get the...
Standard Ignition Spark Plug Wire Set; 8 Cylinder
Spark plug wires are a major component in the vehicles ignition system. Electrical failure can be greatly hastened by loose connections at the ignition coil(s), distributor or spark plugs causing telltale corrosion at...
1972-83 Mopar A/B Body; Ignition Control Module; 5-Pin
5 pin ignition control module replacement unit for 1972-83 Mopar A and B-body models.
1972-89 Mopar A, B & E-Body 8-Cylinder Reluctor
Ignition reluctor replacement unit for 1972-89 Mopar A, B and E-body 8-Cylinder models.
1970-87 Mopar A, B & E-Body 6-Cylinder Hall Effect / Pick-Up Coil
Ignition hall-effect / pick-up coil replacement unit for 1970-87 Mopar A, B and E-body 6-Cylinder models.
1973-76 Mopar A, B & E-Body Reluctor 6-Cylinder
Replacement Ignition reluctor unit designed for use on various 1973-76 Mopar A, B and E-body 6-Cylinder models.
1972-90 Mopar 8 Cylinder Vacuum Advance
The vacuum advance is a primary component in your vehicle's ignition system. Attached to the distributor, the vacuum advance is a mechanism that moves the breaker point or pick-up coil plate when it receives vacuum generated...
1960-76 Mopar Big Block Engine Spark Plug Wire Shield
Factory-style replacement spark plug wire shield for all Mopar Big Block engines from late 1969-76. This exact replacement spark plug wire shield mounts to the fourth exhaust manifold stud from the front of the engine to...
1972-76 Mopar A, B & E-Body 8-Cylinder Hall Effect / Pick-Up Coil
Ignition hall-effect / pick-up coil replacement unit for 1972-76 Mopar A, B and E-body 8-Cylinder models.
1966-76 Mopar with 273 Small Block, Big Block, & Hemi Engines - Ignition Wire Insulator
Ignition wire insulator for Mopar models with 273 Small Block, Big Block and Hemi engines. Injection molded in nylon. Insulates the ignition wires from valve covers or wire routing brackets. Note: Fits spark plug wire routing...
1966-76 Mopar with 273 Small Block, Big Block, & Hemi Engines - Ignition Wire Insulator
Classic $2.99 ea
Flame Thrower 8-Cylinder 7Mm Spark Plug Wires - Black
These Flame Thrower high performance spark plug wires were created with the classic car in mind. They are manufactured in original 7mm size jackets to fit stock wiring looms. With no markings or script of any kind on the...
1973-76 Mopar 6 Cylinder Vacuum Advance
The vacuum advance is a primary component in your vehicle's ignition system. Attached to the distributor, the vacuum advance is a mechanism that moves the breaker point or pick-up coil plate when it receives vacuum generated...
Mopar A, B & E-Body 6-Cylinder Distributor Cap
Standard quality replacement distributor cap for 1962-76 Mopar A, B & E-Body 6-Cylinder models.