Driver Side Mount Performance High-Torque Light Weight Starter 168 Tooth Flywheel
Classic now offers high torque starters that will replace your original with upgraded performance.This high torque, light weight performance starter features 200 ft. lbs. of torque, 4.4:1 gear reduction, billet aluminum...
Driver Side Mount Performance High-Torque Light Weight Starter 168 Tooth Flywheel
Classic $349.99 ea
Starter Bolt 3/8"-16 X 4-11/16"
Replacement starter bolt for models that require a 3/8"-16 x 4-11/16" bolt.
Painless Hot Shot Starter Solution; without Engine Bump Start Switch
The solution for vehicles with GM starters that are hard to start when hot, or vehicles with old or worn out electrical systems. Works by boosting available amperage to the starter solenoid. Installation Instructions:...
Painless Hot Shot Starter Solution; without Engine Bump Start Switch
Classic $36.99 ea
In today's high-heat environment, starters take in a lot of damaging heat that destroys the windings of the starter and solenoid. To combat this problem, we offer a non-conductive strap-on heat shield with a highly-reflective...
Painless Remote Starter Solenoid Set
This set allows you to position the starter solenoid any place you need to in order to make maintenance easier, clean up an inner fender or just replace a factory starting circuit. Installation Instructions: Download Here Set...
Powermaster Mopar replacement starters for all 1965-76 Mopar models. Each starter includes a dyno sheet to show how well the starter you just bought performs.
GM Starter Bolt 3/8"-16 X 1-7/8"
Genuine GM starter bolt for various models. Replaces OE # 14097279 - starter mounting bolt (short) 3/8-16 x 1.87" (or 3/8"-16 X 1-7/8"). Fits most (non gear reduction) small block & big block chevy starters. Sold...
Replacement Shim Kit For P/N 66256
Fits Proform Starter #66256 for Small/Big Block Chevy
3/8"-16 X 3-5/8" Starter Mount Bolt
This replacement shouldered medium length bolt commonly used to secure starters with a cast iron staggered pattern nose to a big block engine. Two bolts required per vehicle.
Touch Sensitive Starter System with Advanced Security - For Use without Ron Francis Harness
Looking for something to set your ride apart, make it more like late model rides? Install this complete touch sensitive starter system from Ron Francis. This system simulates all five positions of a typical keyed ignition...
Painless Hot Shot Plus Starter Solution; with Engine Bump Start Switch
The solution for vehicles with GM starters that are hard to start when hot, or vehicles with old or worn out electrical systems. Works by boosting available amperage to the starter solenoid. The Hot-Shot Plus model includes...
Painless Hot Shot Plus Starter Solution; with Engine Bump Start Switch
Classic $56.99 ea
Starter Bolt; 3/8"-16 X 4.33"; For 4.3L 5.0L 5.7L, or 502 Engine
Genuine GM starter bolts for various models. For 4.3L 5.0L 5.7L, or 502 Engine. Replaces GM Numbers 12338064, 09000852, or 10465167. Works with GM Performance 9000852 or 12606096 high-torque mini starters, also works with...
No more jumping from under the hood, to the front seat, to under the hood! Easily test your engine with the PROFORM Remote Starter Switch.
Replacement Pinion For P/N 66256, 66258 & 66259.
Replacement for Starter #66256, #66258, #66259, and other similar models
Touch Sensitive Starter System with Advanced Security - For Use with Ron Francis Harness
Looking for something to set your ride apart, make it more like late model rides? Install this complete touch sensitive starter system from Ron Francis. This system simulates all five positions of a typical keyed ignition...
1962-76 Mopar A, B & E-Body Starter
Replace your burned-out original starter with these quality remanufactured starter motors. Remanufactured to meet or exceed original factory specifications, each will fit, install and function exactly as original....
Xs-Torque Starter 200 Ft/Lb Chrome
Powermaster Mopar replacement starters for all 1965-76 Mopar models. Each starter includes a dyno sheet to show how well the starter you just bought performs. The torque output of a starter is the most important...
Ultra-Torque Starter 250 Ft/Lb Natural
Powermaster Mopar replacement starters for all 1965-76 Mopar models. Each starter includes a dyno sheet to show how well the starter you just bought performs. The torque output of a starter is the most important...
Ultra-Torque Starter 200 Ft/Lb High Speed Natural
Powermaster Mopar replacement starters for all 1965-76 Mopar models. Each starter includes a dyno sheet to show how well the starter you just bought performs. The torque output of a starter is the most important...
1966-72 Mopar A, B & E-Body; Remanufactured Starter; 3-Bolt
Replace your burned-out original starter with these quality remanufactured starter motors. Remanufactured to meet or exceed original factory specifications, each will fit, install and function exactly as original....
1964-74 Mopar Starter Mounting Hardware Set
Starter mounting hardware set for all 1964-74 Mopar models, excluding Hemi with Manual transmission. Each set includes studs, washers and all other hardware needed to mount the starter. Will not fit direct drive starter....
Powermax Mini-Starter 160 Ft/Lb Natural
Powermaster Mopar replacement starters for all 1965-76 Mopar models. Each starter includes a dyno sheet to show how well the starter you just bought performs. The torque output of a starter is the most important...
Xs-Torque Starter 200 Ft/Lb Natural
Powermaster Mopar replacement starters for all 1965-76 Mopar models. Each starter includes a dyno sheet to show how well the starter you just bought performs. The torque output of a starter is the most important...
Mopar SB & BB; XS Torque Starter; 200 FT/LB; Natural Finish
Powermaster's highly efficient XS Torque starters feature extra-powerful motors that churn out up to 200 lbs.-ft. of torque. Coupled with their 4.4:1 gear-reduction ratio, that equals reliable cranking power for engines, up...
Mastertorque Starter 180 Ft/Lb Natural
Powermaster Mopar replacement starters for all 1965-76 Mopar models. Each starter includes a dyno sheet to show how well the starter you just bought performs. The torque output of a starter is the most important...
Mopar Performance Big Block / 426 Hemi Lightweight Starter
This specially designed starter with heavy duty features for Mopar V8 applications needs no adapaters. Weighing approximately 7 lbs complete, these units are lighter than the pervious Mopar Performance lightweight starter and...
1964-76 Mopar A, B & E-Body Starter
Replace your burned-out original starter with these quality starter motors. Manufactured to meet or exceed original factory specifications, each will fit, install and function exactly as original. Applications: Mopar A, B &...
1965-87 Mopar V8 Xs High-Torque Starter - Natural Finish
Cast-aluminum mounting block with nose. Rated 200 ft/lbs. torque.
High Torque Starter. 100% New. Fits Chrysler Lightweight, V6 & V8, 1.4 Kw, 14:1 Comp.
High-torque, gear-reduction design. 100% NEW, not rebuilt. The high-torque, high-output motor spins the engine over faster than stock starters, delivering more cranking power. 4.41-to-1 sealed gear-reduction drive and full...
High Torque Starter. 100% New. Fits Chrysler Lightweight, V6 & V8, 1.4 Kw, 14:1 Comp.
Classic $153.99 ea
MSD; Mopar Small And Big Block; Dynaforce Starter
MSD DynaForce starters are designed for severe duty, high compression applications. The 3.4 hp motor uses a 4.4:1 gear reduction to easily start even an 18:1 small block or big block Mopar engines with a lower current draw...
1962-76 Mopar A, B & E-Body 6-Cyl & 8-Cyl Starter
Why buy a remanufactured starter when you can buy new at a fraction of the cost? this direct replacement starter is brand new and priced competitively against remanufactured starters. Designed to replace your worn out...
1968-74 Mopar Starter Dust Shield
Replacement starter dust shield for 1968-74 Mopar models. Mounts between starter and bellhousing.
High Torque Starter; Chrysler V6 or V8, 4.41:1 Gear Reduction Ratio
Featuring the retro-style Mopar Emblem, this high-torque, gear-reduction design starter is made entirely of 100 percent NEW, not rebuilt components. Offset design results in more clearance between the oil pan and the starter....
High Torque Starter; Chrysler V6 or V8, 4.41:1 Gear Reduction Ratio
Classic $211.99 ea
1960-64 Mopar A & B-Body 170/225Ci 6-Cylinder 2-Bolt Remanufactured Starter
Replace your burned-out original starter with these quality remanufactured starter motors. Remanufactured to meet or exceed original factory specifications, each will fit, install and function exactly as original....
1960-64 Mopar A & B-Body 170/225Ci 6-Cylinder 2-Bolt Remanufactured Starter
Classic $289.99 ea
Starter/transmission linkage splash shield for A/B Body vehicles. Comes with 10 staples and a drill bit for installation. Original factory assembly line manual shows 9 staples to be used but we have seen anywhere from 5 to 7...
1963-66 Dodge, Plymouth A-Body; 1962-65 B-Body; Starter / Automatic Transmission Linkage Splash Shield
Classic $11.99 ea
1966-68 Charger, Coronet, GTX, Road Runner, Satellite; Ignition Switch Bezel; Chrome; 7/8" ID
Reproduction of the ignition switch bezel for various 1966-68 Dodge Charger, Coronet, and Plymouth Belvedere, GTX, Road Runner, and Satellite models. Replace the scratched, pitted, damaged bezel with this quality reproduction...
1966-68 Charger, Coronet, GTX, Road Runner, Satellite; Ignition Switch Bezel; Chrome; 7/8" ID
Classic $13.99 ea
1967-74 Dodge, Plymouth; Mounting Bolt Set; 4-Piece Set; For Plastic Starter Shields
Starter shield mounting bolt set for plastic starter shields. Each set includes (4) 1/4"-20 x 3/4" Serrated head bolts to mount PLASTIC K Frame and Starter Splash Shields on all 1966-74 auto trans models equipped with the...
1967-74 Dodge, Plymouth; Mounting Bolt Set; 4-Piece Set; For Plastic Starter Shields
Classic $8.99 ea
1966-69 Mopar Starter Mounting Hardware Set
Starter mounting hardware set for all 1966-69 Mopar models with a Hemi engine and manual transmission. This mounting set is for the direct drive starter that was used exclusively on 1966-69 manual Hemi models. Each set...
1970-74 Challenger; Barracuda; Cuda; Starter Heat Shield / Splash Shield; with Auto Trans
Reproduction starter heat shield or sp[lash shield for 1970-74 E-body models. Manufactured in injection molded ABS, this heat shield mounts to the frame and shields the starter from excess heat or the elements on E-Body...
1970-74 Challenger; Barracuda; Cuda; Starter Heat Shield / Splash Shield; with Auto Trans
Classic $203.99 ea
1962-65 Mopar B-Body Starter Splash Shield - Each
Reproduction of the original style starter splash shield designed for use on various Mopar B-body models. Each splash shiled is designed to replace the original exactly. Die-cut to exact dimensions and ready to install. Sold...
Reproduction starter splash shield or heat shield for various 1966-70 Dodge and Plymouth B-Body models. Many times missing and almost always rusted and in need of repair. This shield attaches to the LH front frame rail on...
1966-70 Dodge, Plymouth B-Body; Starter / Automatic Transmission Linkage Splash Shield
Starter/transmission linkage splash shield for 1966-70 B-Body vehicles. Comes with 9 staples and a drill bit for installation. Original factory assembly line manual shows 9 staples to be used but we have seen anywhere from 5...
1966-70 Dodge, Plymouth B-Body; Starter / Automatic Transmission Linkage Splash Shield
Classic $11.99 ea
Starter/transmission linkage splash shield for 1970 E-Body vehicles. Comes with 9 staples and a drill bit for installation. Original factory assembly line manual shows 9 staples to be used but we have seen anywhere from 5 to...
1970 Dodge Challenger TA, Plymouth Barracuda AAR; Starter / Automatic Transmission Linkage Splash Shield
Classic $11.99 ea
1966-70 Dodge, Plymouth B-Body; Starter / Automatic Transmission Linkage Splash Shield
Starter/transmission linkage splash shield for 1965-71 C-Body vehicles. Comes with 9 staples and a drill bit for installation. Original factory assembly line manual shows 9 staples to be used but we have seen anywhere from 5...
1966-70 Dodge, Plymouth B-Body; Starter / Automatic Transmission Linkage Splash Shield
Classic $13.99 ea
1967-72 Dodge, Plymouth A-Body; Starter / Transmission Linkage Splash Shield
Starter/transmission linkage splash shield for A-Body vehicles. Comes with 9 staples and a drill bit for installation. Original factory assembly line manual shows 9 staples to be used but we have seen anywhere from 5 to 7...
1967-72 Dodge, Plymouth A-Body; Starter / Transmission Linkage Splash Shield
Classic $11.99 ea