Product#: PX40011

Pertronix Flame Thrower 8-Cylinder 40,000 Volt 1.5 Ohm Black Oil Filled Ignition Coil

Complete your ignition upgrade with a Flame Thrower high performance ignition coil! The Flame Thrower coil fits into your existing coil bracket for a clean, factory look. Enables larger plug gaps for greater fuel efficiency...

Product#: 12171A

1949-74 Ford, Mercury; Pertronix Ignitor Electronic Ignition; 6 Cylinder; With Thermactor

IGNITOR BREAKERLESS ELECTRONIC IGNITION by PERTRONIX Fits 1965 - 1967 Mustang, 6 cyl. with thermactor (with "C" shaped shaft under rotor). 1968 - 1973 6 cyl. (all) Ignitor electronic ignitions will increase horsepower,...

Product#: D500700

Pertronix Ignitor II Ignition Module

Replacement Ignitor II module for all Pertronix Flame Thrower billet distributors. Gain horsepower, quicker starting and longer plug life. Ignitor II offers enhanced performance levels only found in more expensive "box type"...

Product#: PX40001

Pertronix Flame Thrower 8 Cylinder 40,000 Volt 1.5 Ohm Chrome Oil Filled Ignition Coil

Complete your ignition upgrade with a Flame Thrower high performance ignition coil! The Flame Thrower coil fits into your existing coil bracket for a clean, factory look. Enables larger plug gaps for greater fuel efficiency...

Product#: PX45001

Pertronix Flame Thrower II 4 -6 - 8 Cylinder 45,000 Volt 0.6 Ohm Chrome Oil Filled Ignition Coil

Complete your ignition upgrade with a Flame Thrower II high performance ignition coil! The Flame Thrower coil fits into your existing coil bracket for a clean, factory look. Enables larger plug gaps for greater fuel...

Product#: PX44001

Pertronix Flame Thrower III 8 Cylinder 45,000 Volt 0.32 Ohm Chrome Oil Filled Ignition Coil

The Flame Thrower III Coil is a rapid charge ignition coil to optimize the Ignitor III module. The Flame Thrower III is a traditional oiled filled canister for the "old school" appearance; but will work with modern day...

Product#: PX40111

PerTronix Flame Thrower 8 Cylinder 40,000 Volt 1.5 Ohm Black Epoxy Filled Ignition Coil

Complete your ignition upgrade with a Flame Thrower high performance ignition coil! The Flame Thrower coil fits into your existing coil bracket for a clean, factory look. Enables larger plug gaps for greater fuel efficiency...

Product#: PX45011

Pertronix Flame Thrower II 4 -6 - 8 Cylinder 45,000 Volt 0.6 Ohm Black Oil Filled Ignition Coil

Complete your ignition upgrade with a Flame Thrower II high performance ignition coil! The Flame Thrower coil fits into your existing coil bracket for a clean, factory look. Enables larger plug gaps for greater fuel...

Product#: PX8001

Pertronix Flame Thrower HEI Tune Up Set with Red Distributor Cap (Red/Yellow Coil Wires)

This Performance Tune-Up Set will perk up the performance of your stock GM HEI distributor. Set includes Street/strip 4-pin module and coil combination Premium red distributor cap Premium rotor Coil cover Adjustable vacuum...

Product#: PX104600

Flame-Thrower Cast Stock Look Distributor with Ignitor

This Flame-Thrower distributor from Pertronix looks like a stock point type Chevy distributor but is anything than stock. The distributor is 100% new inside and out, not rebuilt. A hardened precision ground gear with...

Product#: PX20021

1987-91 Pertronix Flame Thrower 8 Pin, 6.0 Amp Ignition Module

This performance ignition module is a direct replacement for GM computer controlled distributors. This module provides enhanced high RPM performance and increase spark plug voltage when used with a corresponding Flame Thrower...

Product#: PX8002

Pertronix Flame Thrower HEI Tune Up Set with Blue Distributor Cap (Red/Yellow Coil Wires)

This Performance Tune-Up Set will perk up the performance of your stock GM HEI distributor. Set includes Street/strip 4-pin module and coil combination Premium blue distributor cap Premium rotor Coil cover Adjustable vacuum...

Product#: PX8000

Pertronix Flame Thrower HEI Tune Up Set with Black Distributor Cap (Red/Yellow Coil Wires)

This Performance Tune-Up Set will perk up the performance of your stock GM HEI distributor. Set includes Street/strip 4-pin module and coil combination Premium black distributor cap Premium rotor Coil cover Adjustable vacuum...

Product#: D650700

Pertronix Flame Thrower Cap Black - Female

Pertronix Flame Thrower Caps are made from high performance 60 KV rated alkyd molding compound for superior protection from "arc-thru" and cross-fire. Direct replacement for Pertronix Flame Thrower billet plug-and-play...

Product#: 12259N

1965-73 Ford Mustang; Pertronix Spark Plug Wires; 8mm; With Straight Boots; Blue

Use with Pertronix Distributors only

Product#: PX1381A

1959-72 Mopar V8 Pertronix Ignitor Kit - Single Point Vacuum Advance

The Pertronix IGNITOR eliminates the hassle of points and moving parts that wear out while delivering twice the voltage to the spark plugs over stock to increase horsepower, fuel economy and spark plug life. Optimal...

Product#: PX40511

Pertronix Flame Thrower 6-Cylinder 40,000 Volt 3.0 Ohm Black Oil Filled Ignition Coil

Complete your ignition upgrade with a Flame Thrower high performance ignition coil! The Flame Thrower coil fits into your existing coil bracket for a clean, factory look. Enables larger plug gaps for greater fuel efficiency...

Product#: PX1385LS

1951-71 Mopar Pertronix Ignitor Lobe Sensor Ignition Module; Dual Point Replacement

Pertronix Ignitor dual-point lobe sensing ignition module. The Ignitor is Pertronix' most advanced points replacement kit yet, packing many of the features of an ignition box inside your distributor. It features multiple...

Product#: PX1168

1941-62 6 Cylinder Pertronix Ignitor Set

Eliminates points and moving parts that wear out, while delivering twice the voltage to the spark plugs over stock to increase horsepower, fuel economy and plug life! Ignitor is concealed entirely within the distributor so...

Product#: PX1162A

1963-74 6 Cylinder Pertronix Ignitor Set

Eliminates points and moving parts that wear out, while delivering twice the voltage to the spark plugs over stock to increase horsepower, fuel economy and plug life! Ignitor is concealed entirely within the distributor so...

Product#: *12172A

Black Single Point V8 Pertronix Ignition Set

Sets are available with 40,000 volt Black or Chrome Pertronix Coils. Sets include 1 Pertronix Ignitor Electronic Ignition, 1 Pertronix Flame Thrower Coil and 1 Pertronix Flame Thrower Spark Plug Wire Set.

Product#: PX91181

1957-74 V8 Dual Point Pertronix Ignitor II Set with Hall-Effect Style Sensor

The Ignitor II electronic ignition goes an extra step beyond for even more power and efficiency! It senses levels of current in the coil, and uses a powerful micro controller to adjust the dwell to maintain peak energy...

Product#: PX708101

1955-70 Small Block V8 283, 307, 327, 350, 400 Pertronix Flame Thrower 7MM Spark Plug Wire Set

Flame Thrower high performance spark plug wires were created with the classic car in mind. They are manufactured in original 7mm size jackets to fit stock wiring looms. With no markings or script of any kind on the wire, they...

Product#: D7500700

Pertronix Ignitor III Ignition Module

Upgrade/replacement Ignitor III module for 8 cylinder automotive Pertronix billet distributors. These distributor modules are direct bolt-in replacements for your Pertronix Flame Thrower III distributor. Installed easily and...

Product#: 12171C

1960-73 Mustang, Cougar, Falcon; 221-460 V8; Dual Point Distributor; Mechanical Advance; Pertronix Ignitor I Electronic Ignition Conversion

IGNITOR BREAKERLESS ELECTRONIC IGNITION by PERTRONIX Fits 1965 - 1973 Mustang, 8 cyl. (dual point)Ignitor electronic ignitions will increase horsepower, improve fuel economy, and extend spark plug life. Enjoy all the benefits...

Product#: PX9011

Distributor Vacuum Advance Lockout; Counter Clockwise

This vacuum advance lockout mounts to the distributor and is used when switching from a vacuum advance to a mechanical advance.

Product#: PX45111

Pertronix Flame Thrower II 4 -6 - 8 Cylinder 45,000 Volt 0.6 Ohm Black Epoxy Filled Ignition Coil

Complete your ignition upgrade with a Flame Thrower II high performance ignition coil! The Flame Thrower coil fits into your existing coil bracket for a clean, factory look. Enables larger plug gaps for greater fuel...

Product#: PX91162

1963-74 6 Cylinder Pertronix Ignitor II Set

The Ignitor II electronic ignition goes an extra step beyond for even more power and efficiency! It senses levels of current in the coil, and uses a powerful micro controller to adjust the dwell to maintain peak energy...

Product#: PX40501

Pertronix Flame Thrower 6 Cylinder 40,000 Volt 3.0 Ohm Chrome Oil Filled Ignition Coil

Complete your ignition upgrade with a Flame Thrower high performance ignition coil! The Flame Thrower coil fits into your existing coil bracket for a clean, factory look. Enables larger plug gaps for greater fuel efficiency...

Product#: 12171H

1954-56 Ford; 239-312 Y-Block V8; Single Points, Vacuum Advance; PerTronix Ignitor I Electronic Ignition Conversion Kit; 12-Volt Negative Ground

The Ignitor replaces the breaker points in most "older" points style ignitions with a dependable, self contained, and maintenance free electronic system.

Product#: PX1181

1957-74 V8 Dual Point Pertronix Ignitor Set with Hall-Effect Style Sensor

Eliminates points and moving parts that wear out, while delivering twice the voltage to the spark plugs over stock to increase horsepower, fuel economy and plug life! Ignitor is concealed entirely within the distributor so...

Product#: PX20011

1980-91 Pertronix Flame Thrower 7 Pin, 6.0 Amp Ignition Module

This performance ignition module is a direct replacement for GM computer controlled distributors. This module provides enhanced high RPM performance and increase spark plug voltage when used with a corresponding Flame Thrower...

Product#: MN2239

1960-72 Mopar 6 Cylinder Ignitor Electronic Ignition System

Eliminate points and wear-prone moving parts while delivering twice the stock voltage to the spark plugs. The Ignitor fits completely inside the distributor with no complex wiring, leaving no unsightly black box to clutter up...

Product#: *12172C

Pertronix Ignition Set Black 6 Cylinder without Thermactor Pump

Sets are available with 40,000 volt Black or Chrome Pertronix Coils. Sets include 1 Pertronix Ignitor Electronic Ignition, 1 Pertronix Flame Thrower Coil and 1 Pertronix Flame Thrower Spark Plug Wire Set.

Product#: PX1181LSC

1957-74 V8 Pertronix Ignitor Set with Point-Lobe Style Sensor

Eliminates points and moving parts that wear out, while delivering twice the voltage to the spark plugs over stock to increase horsepower, fuel economy and plug life! Ignitor is concealed entirely within the distributor so...

Product#: PX44011

Pertronix Flame Thrower III 8 Cylinder 45,000 Volt 0.32 Ohm Black Oil Filled Ignition Coil

The Flame Thrower III Coil is a rapid charge ignition coil to optimize the Ignitor III module. The Flame Thrower III is a traditional oiled filled canister for the "old school" appearance; but will work with modern day...

Product#: D600700

Pertronix; Flame Thrower Cap & Rotor Kit; Female Terminals; Black

Pertronix cap and rotor set for 8 cylinder Flame Thrower billet distributors. Made from high-performance 60 KV rated alkyd molding compound for superior protection from "arc-through" and cross fire. Includes rotor and rotor...

Product#: D701700

Pertronix Distributor Vacuum Advance

From replacement vacumm canisters to vacuum advance lockout kits and mechanical advance kits, we have the parts to get your HEI distributor in top condition. Vacuum advance for all Pertronix billet distributors. These vacuum...

Product#: PX91381A

1964-74 Mopar V8 Pertronix Ignitor II Kit

The Ignitor II electronic ignition goes an extra step beyond the standard Ignitor for even more power and efficiency! It senses level of current in the coil and uses a powerful micro-controller to adjust the dwell to maintain...

Product#: D700700

Pertronix; Distributor Mechanical Advance Spring Kit

Pertronix billet distributor advance spring kits are designed to adjust the mechanical advance curve. They include three sets of springs to help you get the correct setting. The spring kits are designed to fit Pertronix...

Product#: PX9010

Distributor Vacuum Advance Lockout; Clockwise

This vacuum advance lockout mounts to the distributor and is used when switching from a vacuum advance to a mechanical advance.

Product#: PX40611

Pertronix Flame Thrower 6 Cylinder 40,000 Volt 3.0 Ohm Black Epoxy Filled Ignition Coil

Complete your ignition upgrade with a Flame Thrower high performance ignition coil! The Flame Thrower coil fits into your existing coil bracket for a clean, factory look. Enables larger plug gaps for greater fuel efficiency...

Product#: PX71181

1957-74 V8 Pertronix Ignitor III

The Ignitor III offers ignition box performance without the box. The Ignitor III is the most advanced points replacement kit. It literally is an ignition box which goes inside your distributor. It fires multiple sparks...

Product#: PX3001

1977-91 GM HEI In-Cap Mounted Pertronix Flame-Thrower Coil with Black, White and Red Wires

This Pertronix Flame Thrower 50,000 volt E-Core coil features an optimized winding design to maximize spark gap current and available voltage. Includes all necessary hardware. When teamed with a Flame Thrower module (sold...

Product#: 12171P

1965-73 Ford Mustang; Pertronix Ignitor III; V8 With Dual Point Distributor

Provides ignition box performance without the box! Bolts into factory Ford point - type distributors, completely replacing the points and condensor. Upgrade to modern electronic ignition, while retaining the classic restored...

Product#: D671001

Pertronix Distributor Gear

Bronze gear Chevrolet 90° V6, SB, BB, 348-409 (0.5" shaft). Pertronix distributor gears are designed to fit Pertronix Flame-Thrower distributors. Pertronix bronze distributor gears are made from premium bronze alloy.

Product#: 12171G

1965-73 Ford Mustang; Pertronix Ignitor Electronic Ignition; Mallory MAL2555101 Distributor For Ford Mustang

IGNITOR BREAKERLESS ELECTRONIC IGNITION by PERTRONIX For Mallory mal2555101 distributor for MustangsIgnitor electronic ignitions will increase horsepower, improve fuel economy, and extend spark plug life. Enjoy all the...

Product#: 12171L

1964-73 Ford Mustang; Pertronix Ignitor II; V8 Fords With Single Point Motorcraft Distributors

The Ignitor II senses current levels in the coil and adjust the dwell to maintain peak energy throughout the entire RPM range. Dwell time is increased or decreased with changing engine RPM and operating conditions. This...

Product#: D600701

Pertronix; Flame Thrower Cap & Rotor Kit; Female Terminals; Red

Pertronix cap and rotor set for 8 cylinder Flame Thrower billet distributors. Made from high-performance 60 KV rated alkyd molding compound for superior protection from "arc-through" and cross fire. Includes rotor and rotor...

Product#: D600711

Pertronix; Flame Thrower Cap & Rotor Kit; Male Terminals; Red

Pertronix cap and rotor set for 8 cylinder Flame Thrower billet distributors. Made from high-performance 60 KV rated alkyd molding compound for superior protection from "arc-through" and cross fire. Includes rotor and rotor...

Product#: PX60104

Pertronix 60,000 Volt 0.45 Ohm Flame Thrower HV Ignition Coil

The Flame Thrower HV (high voltage) coil has an E-Core design which is rated at a sizzling 60,000 volts and operates with no degradation of energy throughout the temperature ranges. Made from 6063 T5 aluminum, it efficiently...

Product#: PX3002

1985-95 GM Remote Mounted HEI Pertronix Flame-Thrower Coil

This Pertronix Flame Thrower 50,000 volt E-Core coil features an optimized winding design to maximize spark gap current and available voltage. When teamed with a Flame Thrower module (sold separately) it produces 100% more...

Product#: PX71381A

1960-72 Mopar V8 Pertronix Ignitor III Kit - Single Point Distributor Only

Pertronix' Ignitor III system offers you ignition box performance without the box! The Ignitor III is the most advanced points replacement setup available. The Ignitor III literally is an ignition box, just inside of the...

Product#: MN2243

1960-72 Mopar 6 Cylinder Ignitor II Electronic Ignition System

The Ignitor II detects electrical current in the coil and uses a micro controller to increase or decrease dwell to maintain peak energy as RPM and operating conditions change, providing more energy, reducing misfires, and...

Product#: *12172D

Pertronix Ignition Set Chrome Single Point V8

Sets are available with 40,000 volt Black or Chrome Pertronix Coils. Sets include 1 Pertronix Ignitor Electronic Ignition, 1 Pertronix Flame Thrower Coil and 1 Pertronix Flame Thrower Spark Plug Wire Set.

Product#: *12172E

Pertronix Ignition Set Chrome 6 Cylinder with Thermactor Pump

Sets are available with 40,000 volt Black or Chrome Pertronix Coils. Sets include 1 Pertronix Ignitor Electronic Ignition, 1 Pertronix Flame Thrower Coil and 1 Pertronix Flame Thrower Spark Plug Wire Set.

Product#: D71370

1969-97 Ford; 221-302 SBF V8; PerTronix Flame Thrower Race HEI Distributor w/ Ignitor III Module; Machined Finish; MechanicalAdvance; HEI Cap; Black

PerTronix Race HEI Flame Thrower III distributors use all new components and compared to our street or strip version, race units produce 42 percent more energy with 46 percent faster spark breakdown time allowing 48 percent...

Product#: PX60115

Pertronix 60,000 Volts 1.5 Ohm Flame Thrower HV Ignition Coil

The Flame Thrower HV (high voltage) coil has an E-Core design which is rated at a sizzling 60,000 volts and operates with no degradation of energy throughout the temperature ranges. Made from 6063 T5 aluminum, it efficiently...

Product#: PX60130

Pertronix 60,000 Volts 3.0 Ohm Flame Thrower HV Ignition Coil

The Flame Thrower HV (high voltage) coil has an E-Core design which is rated at a sizzling 60,000 volts and operates with no degradation of energy throughout the temperature ranges. Made from 6063 T5 aluminum, it efficiently...

Product#: PX3000

1974-88 GM HEI In-Cap Mounted Pertronix Flame-Thrower Coil with Black, Yellow and Red Wires

This Pertronix Flame Thrower 50,000 volt E-Core coil features an optimized winding design to maximize spark gap current and available voltage. Includes all necessary hardware. When teamed with a Flame Thrower module (sold...