Classic Industries Restoration Parts and Accessories - Carburetor Components

Throttle Body Spacers Enhance Mid-Range Power, Torque And Fuel Efficiency! The Poweraid Throttle Body Spacer is designed to cause a spinning action of the incoming air charge as it passes through the throttle body. This air...

Throttle Body Spacers Enhance Mid-Range Power, Torque And Fuel Efficiency! The Poweraid Throttle Body Spacer is designed to cause a spinning action of the incoming air charge as it passes through the throttle body. This air...

Throttle Body Spacers Enhance Mid-Range Power, Torque And Fuel Efficiency! The Poweraid Throttle Body Spacer is designed to cause a spinning action of the incoming air charge as it passes through the throttle body. This air...

Throttle Body Spacers Enhance Mid-Range Power, Torque And Fuel Efficiency! The Poweraid Throttle Body Spacer is designed to cause a spinning action of the incoming air charge as it passes through the throttle body. This air...

This Lokar Hi-Tech "U-Cut-to-Fit" outer housing with a "U-Cut-to-Fit" stainless inner wire throttle cable is designed with a specially extruded liner for extended service life and innovative clevis cable ends to eliminate the...

Old cables sometimes stick and may not operate properly. Our new throttle cable mounts to the dash and can give reliable operation to the throttle. Cables come with mounting hardware and knob.

Reproduction of the original aluminum carburetor fitting designed for use with 1968-75 Pontiac models including Firebird and Trans Am. This particular fitting was used on most all 1968-69 Firebird models, but can also be used...

For efficient choke operation, make sure your choke heat tube is present and clear of obstructions.

Old worn out choke tubes can become a problem when you try to start your car. Replace it with a new unit and get your Mustang running just the way it should. Made in USA

Reproduction thermal choke tube for 1957 Chevy models. This choke tube features all the correct contours for an exact replacement.

Reproduction of the original accelerator throttle cable that connects the accelerator pedal to the carburetor. If your original cable is worn, or you don't have immediate acceleration when presseing the pedal, you may want...

The throttle valve carburetor bracket is designed for use with specific carb and transmission set-ups to correct the linkage geometry at the carburetor for proper upshifts and downshifts.

This throttle cable is designed with a specially extruded liner to extend the life of the cable. Cables are equipped with aluminum fittings and aluminum ferrule to eliminate fraying. Clevis is designed to eliminate cotter...

This bracket is designed to be used on Holley 4150 and 4160 square bore carburetors only. It bolts onto the carburetor flange ear and provides a convenient mounting point for transmission kickdown and throttle cables.

Reproduction thermal choke tubes for street Hemi models. Each set includes upper and lower tubes and a white heat-resistant cover for the upper tube. The lower tube has the correct fitting to screw into the right hand exhaust...

Reproduction thermal choke tube for 1957 Chevy models. This choke tube features all the correct contours for an exact replacement.

Reproduction heat-riser choke tube set ford various 1960-69 Ford and Mercury 6-cylinder models including Mustang, Falcon, Ranchero, and Comet. This set fits 144, 170, and 200 cid "Falcon-Six" engines with automatic choke...

Reproduction thermal choke tubes for 1957 Chevy models. This choke tube features all the correct contours for an exact replacement.

1958-61 Chevrolet 2x4 carburetor throttle lever. Throttle is mechanism by which flow of fluid is managed. Engine's power output can be increased or decreased by restriction of air and fuel with this lever. Made from steel as...

To provide rich fuel mixture required to sustain operation at low engine temperatures, a choke is used to restrict flow of air at entrance of carburetor, before the venturi. With this restriction, extra vacuum is developed in...

1956 and early 1957 Chevrolet 2x4 carburetor secondary air valves are connected by cam and linkage to secondary fuel metering rods. As airflow increases through secondary bores, air valves are pushed down, rotating the cam...

We now offer a variety of stud sets to fit just about any Holley or Rochester carburetor. Set includes: 4 studs 4 nuts 4 washers For 1-3/8" set see Part # T2046 For 3" set see Part # T2106

Choke housing plug / cap. This cap covers the adjustment hole in the side of the choke housing.

After you rebuild your original carburetor, make sure you go into the details that make it shine above all the others. Replace the original slotted filister head screws with these reproductions that are cad plated with...

Reproduction of the original accelerator throttle cable bracket for use on 1970-72 Camaro and Firebird models with Holley Carburetors. This quality bracket is manufactured in stamped steel to the original factory...

Holley EFI spread bore sealing plate. This plate adapts a dual bolt pattern square bore carburetor or throttle body to a spread bore manifold and seal properly. Includes a 1/16" thick plate and two gaskets..

Correct wing nut used with all carburetors with 1/4" carburetor studs. After years of use your original air cleaner can become rusted or broken. This wing nut is the perfect replacement for a rusty or damaged original. Fits a...

We now offer a selection of the most commonly needed Holley carburetor gaskets. Made in USA

This Lokar Hi-Tech "U-Cut-to-Fit" outer housing with a "U-Cut-to-Fit" stainless inner wire throttle cable is designed with a specially extruded liner for extended service life and innovative clevis cable ends to eliminate the...

Quality manufactured throttle cable mounting bracket for 440 Six Pack applications. Now you can stop scouring swap meets and salvage yards for this hard-to-find part. Each bracket comes complete with hold down and features...

This Lokar Hi-Tech "U-Cut-to-Fit" black polished stainless steel outer housing with a "U-Cut-to-Fit" stainless inner wire throttle cable is designed with a specially extruded liner for extended service life and innovative...

Carburetor spacer kits are now available for Holley carburetors. Each kit includes mounting hardware and gaskets.

This Ford Throttle Lever Kit will allow you to connect 1967 and newer Ford automatic transmission kick-down linkage to the Edelbrock Performer Series Carburetor (will not work with AOD trans). If your vehicle has cable-type...

Replace your missing carburetor vent tubes. Keep the original carburetor on your Chevrolet by replacing the missing parts. Why replace the carburetor and loose points at the next car show.

Lokar now offers cables in a variety of colors derived from an outer covering of woven cotton strands which harkens back to the vintage era of hot-rodding. To protect the cotton, each cable is clear-coated for years of...

Lokar Duo-Pak throttle cable set will easily adapt to most gas pedals and throttle assemblies. Cable comes equipped with aluminum fittings and aluminum ferrules to eliminate fraying and feature a "U-Cut-to-Fit" outer housing...

We offer a selection of the most commonly needed Holley carburetor gaskets. Made in USA

Carburetor to intake manifold heat shield. This shield when applied to intake manifold, will keep fuel in carburetor from reaching high temperatures due to engine block heat. Excellent for use on high performance engines. For...

We offer a selection of the most commonly needed Holley carburetor gaskets. Sold as a pair. Important: Will not work with accelerator pump transfer tube.

Now you can select from a variety of 30cc and 50cc aluminum accelerator pump covers with levers to match the latest carburetor finishes.

Now you can select from a variety of 30cc and 50cc aluminum accelerator pump covers with levers to match the latest carburetor finishes.

Now you can select from a variety of 30cc and 50cc aluminum accelerator pump covers with levers to match the latest carburetor finishes.

These Holley jets are the professional way to track-tune your Holley carburetor for top performance. Jets will give the broadest range of adjustment and performance for most performance carburetor applications Sold only as a...

Carburetor to accelerator lever cable. This accelerator cable is designed to replace the original cable on 1970-73 models equipped with 4 bbl carburetors. Applications: 1970-1970 Chevrolet Camaro (with 4 bbl) 1971-1973...

As throttle gradually opens from fully closed position, throttle plates uncover additional area where low pressure is created. Allows for more fuel to flow and compensates for reduced vacuum that occurs when throttle is...

This throttle lever adapter fits 1966 and later vehicles to correctly adapt Performer and Thunder Series carburetors for use with the original cables. Features a black finish and works with vehicles equipped with cruise...

This universal throttle cable mounting bracket (also known as a throttle valve cable correction bracket) attaches to the rear left ear of the carburtetor. Designed to work with MN2236 Torqueflite kickdown cable set or as a...

1958-61 Chevrolet 2x4 carburetor fast idle cam prevents throttle plate from closing fully while choke is in operation, causing engine to idle at higher speed. Fast idle serves as a way to help engine warm up quickly. Fast...

Lokar now offers cables in a variety of colors derived from an outer covering of woven cotton strands which harkens back to the vintage era of hot-rodding. To protect the cotton, each cable is clear-coated for years of...

Reproduction secondary diaphrahm for six-pack equipped 1969-72 Mopar models. This is the rubber diaphragm only, housing not included. Replace this diaphragm to restore functionality to your Mopar's vacuum-driven components. ...

This set includes a selection of metering rods, jets, and step up springs that allow fine tuning and calibration of Edelbrock Performer carburetors for mildly to extremely built motors, especially motors with performance...

This set includes a selection of metering rods, jets, and step up springs that allow fine tuning and calibration of Edelbrock Performer carburetors for mildly to extremely built motors, especially motors with performance...

Reproduction throttle bracket for Mopar models equipped with a 361/383 engine, and 2x4 inline carburetors. Features the correct shape for a proper for a proper fit.

Lokar Hi-Tech cut-to-fit throttle cables are designed with specially extruded liners for extended service life and innovative clevis cable ends to eliminate the fraying and failure associated with cotter pins and set screws. ...

Reproduction of the original throttle switch assembly designed for use with 1970-73 Pontiac Trans Am models. This assembly features all the components necessary to replace the original throttle switch assembly that mounts on...

These Holley jets are the professional way to track-tune your Holley carburetor for top performance. Jets will give the broadest range of adjustment and performance for most performance carburetor applications Sold only as a...

Edelbrock throttle lever adapter designed for Ford automatic transmission equipped vehicles with cable operated throttle (except A.O.D.). Use with appropriate throttle cable plate when necessary. Available in black fnish and...

This vacuum secondary diaphragm fits most 4150 and 4160 square bore Holly carburetors.

Factory-correct reproduction carburetor to intake manifold gasket for 1977-79 Trans Am models with Olds 403ci V8 engine.

Correct replacement 8-32 x 5/8? phillips head screws in the zinc dichromate finish as original. If your Holley Six Pack vacuum diaphragm pot screws are damaged or missing, replace them with these correct replacement...