Chevrolet V6 / V8 Engine; Oil Pump Primer with Bushing
Don't start your engine after a rebuild or major engine disassembly without first making sure there is oil at all the critical friction points such as main, rod and cam bearings, rings and cylinders, as well as the lifters...
1986-87 Buick Regal & 1989 Turbo Trans-Am; Turbo Tweak Scanmaster-G Gauge
Turbo Tweak scanmaster gauge will assist in tuning and troubleshooting various sensor functions. Features a flash memory chip and will store logs that you can download later. It also has a bluetooth module so you can log from...
1986-87 Buick Regal & 1989 Turbo Trans-Am; Turbo Tweak Scanmaster-G Gauge
Classic $259.99 ea
1986-87 Buick Regal Turbo; Turbo Tweak Powerlogger
The Powerlogger is the most advanced data logging scan tool for 1986-87 turbo models. The tool connects to the USB port on a laptop computer and into the vehicle's ECM access port. It reads all the basic engine parameters...
This handy tool removes and installs spring tension hose clamps used on heater and radiator hoses. Adjustable tips screw in and out to fit clamps of all sizes. Ratcheting lock mechanism holds the clamp in an open position for...
Positive stop to locate top dead center. A must for cam checking with heads installed. For 14 mm thread.
Slowly put down the rubber mallet and do the job the right way. LS main caps have very tight tolerances, and cannot be removed by simply grabbing and pulling on them. Uniform pressure from both sides is the only way to do...
Harmonic Balancer Installation Tool. Fits Ford/Pontiac/Buick/Olds Crankshafts
This harmonic balancer installation tool is designed for use with early model Ford, Pontiac, Buick, and Oldsmobile crankshafts. Made from high quality steel material. This tool makes installing the harmonic balancer simple...
Harmonic Balancer Installation Tool. Fits Ford/Pontiac/Buick/Olds Crankshafts
Classic $38.99 ea
PROFORM's Professional Crankshaft Turning Socket is for the serious Cheyy LS engine builder and tuner. This handy tool easily attaches to the oil pump drive lug splines. Once it's attached, pop an oversized degree wheel on...
Ls1, Ls2, & Ls6 Valve Spring Compressor Tool.
This LS valve spring compressor is compact, is activated with normal hand tools, and takes up almost no space in your toolbox. It will cut valve spring removal and replacement time to around 1-hour. And, it's guaranteed to...
Harmonic Balancer Install Tool For Ls-Engine
This harmonic balancer installation tool is designed for use with Chevy LS crankshafts. Made from high quality steel material. This tool makes installing the harmonic balancer simple and easy. Just thread the proper end into...
1971-82 Chevrolet; Small Block Engine Lift Bracket Set
These lift brackets were installed on the intake manifold for quick assembly ease on the production line. If your brackets are missing, it means they were removed during the cars history. To receive full judging points, or...
Engine Crankshaft Turning Nut; Fits Sb Chevy Engine Crankshafts
This heavy duty crankshaft turning nut easily installs through the harmonic balancer and into the end of the crankshaft with the included grade 8 bolt. Once that's done, your balancer is held securely, and you have turning...
These engine lift brackets are designed to bolt to the ends of each cylinder head to remove the engine from the vehicle. Brackets are made from.020" thick steel and have an.88" x 1.00" hook slot. Each is painted with epoxy...
Essential tool for bolts with tight clearance like spark plugs and header bolts! 12-point for maximum finger traction. Set of three including 1/4" x 1/4", 1/4" x 3/8", 3/8" x 3/8" (12 pt x socket drive size). These belong in...
Removes spark plug wire boots from plugs with minimal effort. Designed for use on most cars and trucks. Performs well in difficult areas such as recessed and obstructed plugs. Square shaft prevents slipping and thick plastic...
Vacuum Gauge and Fuel Pump Pressure Tester
Tests for fuel line pressure and vacuum leaks. Check for leaky valves, timing, fuel pump, vacuum, pressure and gas line leakage. Easy to read gauge with 3 foot hose and vacuum hose adapter fitting. Gauge measures vacuum from...
Cleans and threads directly in the spark plug hole! Double ended for both 14mm and 18mm threads. Use with 13/16 spark plug socket.
Universal Cam Degree Wheel Set
This set contains all the tools needed to degree cams in most popular engines, assuring proper timing and lift. Set includes: 9" degree wheel Dial indicator and mount 2 valve check springs Clamp kit 14mm top dead center...
Small Block 7/16" Push Rod Length Checker
Use this tool to check the length of push rods on small block Chevrolet engines. Proper push rod length is critical for peak performance to minimize bent or broken valve stems, guide wear, and energy-wasting valve...
Makes compressing the spring and removing the keepers a simple job because there is no need to remove the head. Faster than conventional compressors because there is no need to readjust the tool after each spring.
Valve Lash Wrench Set - 9/16" Wrench with 3/16" and 7/32" Allen
T-Handle valve lash adjusting wrenches make adjustment very easy, cutting the adjusting time in half. Simply position the adjusting handle wrench over the rocker arm lockdown, and drop the T-handle down through the hole in...
11 precision steel blades are offset to make adjustment of valve tappets easy. Blades are approximately 1/2" wide by 4" long. Includes:.008".010".012".013".014".015".016".018".019".020".026"
Rocker Stud and Tap Alignment Tool
Make removing the rocker studs easier by using this special tool designed for not only removing rocker studs, but aligning as well.
Valve Lash Wrench Set 5/8" Wrench with 3/16" and 7/32" Allen
T-Handle valve lash adjusting wrenches make adjustment very easy, cutting the adjusting time in half. Simply position the adjusting handle wrench over the rocker arm lockdown, and drop the T-handle down through the hole in...
Valve Lash Wrench Set - 1/2" Wrench with 3/16" and 1/8" Allen
T-Handle valve lash adjusting wrenches make adjustment very easy, cutting the adjusting time in half. Simply position the adjusting handle wrench over the rocker arm lockdown, and drop the T-handle down through the hole in...
Use this Degree Wheel to find top dead center or for checking camshaft timing. Step-by-step instructions included with each Degree Wheel. Can be used with crankshaft turning sockets (sold separately).
Small Block 3/8" Push Rod Length Checker
Use this tool to check the length of push rods on small block Chevrolet engines. Proper push rod length is critical for peak performance to minimize bent or broken valve stems, guide wear, and energy-wasting valve...
Chevrolet Small Block Crankshaft Turning Socket
Professional grade crankshaft socket with degree wheel attachment. Can be used with 9" degree wheel part # 66791 or degree wheel kit part # 66787 (both sold separately).
Crankshaft rotation adapter for Chevrolet V8 engines allows the use of a 1/2" drive breaker bar or a 1" socket and breaker bar to rotate the crankshaft when turning the engine with the balancer already installed. Useful when...
Valve Lash Wrench Set - 7/16" Wrench with 1/8" Allen
T-Handle valve lash adjusting wrenches make adjustment very easy, cutting the adjusting time in half. Simply position the adjusting handle wrench over the rocker arm lockdown, and drop the T-handle down through the hole in...
Includes 31 blades and 1 brass blade for use with electronic ignitions. Precision blades ensure an accurate measurement. Blades from 0.10 to 0.35 (.254mm to.889mm) are approximately 1/4 wide by 1 3/4 long.
Connecting Rod Balancer Chevy S/B
Here's the quick and dirty way to match weigh your small block Chevy connecting rods! Simply put two connecting rods on the roller, even them out, and set the roller on the base. You'll quickly determine if your rods are...
Small Block Crank Turning Socket
Socket used for turning the crankshaft on small block Chevy engines.
Installing a camshaft just got easier by using the right tool. Perfect tool for all Chevrolet V6 and V8 engines.
Swivel Grip Oil Filter Wrench; Fits 3-1/2" to 3-7/8" Filters
Handle Swivels to Clear Obstructions. Features the swivel handle, gripper "teeth" and 1" wide stainless steel band. The swivel handle makes it easy to turn filters in hard to reach locations. Vinyl covered handle. Fits 3-1/2"...
The Auto engine stand is designed to make it easier to work on your engine. Used in conjuction with the auto accessory stand (# M998083), this will make it much easier to rebuild your engine.
Oil Pressure and Stop Light Swtch Socket; Fits 1-1/16" Switches Up To 2-5/8" Long
Easily remove oil pressure sending units! This socket designed with extra recess to accommodate most oil pressure switches and many brake lamp switches. This 3/8" drive socket features a 1-1/16" hex opening and a durable...
Oil Pressure and Stop Light Swtch Socket; Fits 1-1/16" Switches Up To 2-5/8" Long
Classic $10.99 ea
Seam Tape consists of a two layer, highly reflective foil with a special acrylic adhesive system. This flame retardant tape is highly puncture proof, tear resistant and features superior adhesion even under the most extreme...