Product#: AL124

Accelerator Throttle Rod; Universal Fit

Universal style accelerator throttle rod for various GM, Ford, Chrysler, Dodge, Plymouth models. This accelerator rod is for use when modifications will not allow the use of the original rod between the accelerator pedal...

Product#: TF100418

1955-57 Chevy Bel Air, Corvette, 150, 210, Nomad; Accelerator Pedal Pad

Reproduction accelerator pedal pad for 1955-57 Chevrolet Bel Air, One-Fifty Series, Two-Ten Series, and Nomad models. Manufactured to original factory specifications, this pedal pad replicates the original fit, appearance,...

Product#: 3798256

1955-69 GM; Accelerator Pedal Firewall Bushings; 1/2" Long, 5/16" I.D.; Pair

Reproduction accelerator firewall bushings for various 1955-69 GM models. These bushings are required to install the accelerator rod support correctly. They help to eliminate excessive play in the gas pedal pad while...

Product#: 4868300

1958-71 GM; Accelerator Pedal Ball Stud Pivot; 1/4"-20 x 1-1/2"; Each; Various Models

Reproduction factory ball stud pivot for various GM models. 1/4"-20 x 1-1/2". Accelerator pedal ball studs can break after many years of use and will need to be replaced. Check your stud for wear when replacing the gas pedal...

Product#: K521

1949-82 GM; Accelerator Rod Grommet and Sleeve Set ; Various Models

OER® reproduction of the original accelerator rod grommet and sleeve unit where the accelerator rod fits into the linkage. This grommet often deteriorates due to engine heat or chemical spillage. Replacing the grommet will...

Product#: 3864740

1964-71 Chevrolet Car & Truck; Floor Mounted Accelerator Pedal Pad; Rubber; with Steel Insert; Factory Style Reproduction

Correct OER® reproduction of the original floor mounted accelerator pedal pad installed on various GM models. Manufactured in quality hard EPDM rubber, this pad is a great upgrade over plastic service replacement pads and...

Product#: MB327

1966-70 Charger, Coronet, Belvedere, GTX, Superbird; Accelerator Pedal Pad; Floor Mounted; with Steel Core

Reproduction of the original accelerator pedal pad designed for use on 1966-70 Belvedere, Charger, Road Runner, Satellite and Superbird B-Body models. This quality reproduction is manufactured in hard rubber material...

Product#: MN2228

1970-74 Dodge, Plymouth; B &E-Body; Accelerator Throttle Cable; with 400, 426, 440; 20"; OER

Reproduction of the original accelerator throttle cable designed for use on 1970-74 Dodge and Plymouth B and E body big block (400, 426, 440) models as listed. Each cable is manufactured to correct factory specifications...

Product#: MN2225

1968-70 Charger, Coronet, GTX, Satellite, Road Runner; Throttle Cable; with Hemi; 19-3/4"; OER

Reproduction of the original throttle cable designed for use with 1968-70 Dodge Charger, Coronet, Super Bee, and Dodge, Plymouth B-Body Hemi models. Connect the accelerator linkage to the carburetor with this original style...

Product#: MN2231

1967-74 Dodge, Plymouth A-Body; Accelerator Throttle Cable; 383, 440; 18"; OER

Reproduction of the original accelerator throttle cable designed for use on 1970-74 Dodge and Plymouth A body models with 383, 440 engines. Each cable is manufactured to correct factory specifications replicating the original...

Product#: 3924409

1964-69 Chevrolet; Accelerator Pedal Pad to Rod Support; OE Style; Steel Reproduction; Various Models

Reproduction of the original style stamped steel accelerator pedal pad to rod support unit. This steel reproduction is manufactured to replicate the original in appearance, design and functionality. Includes correct style...

Product#: K919

1967-2004 Buick, Chevy, Oldsmobile, Pontiac; Accelerator Pedal; Various GM Models

Reproduction accelerator pedal for 1968-2004 GM vehicles. Manufactured in injection molded ABS, this pedal replicates the original in fit and design to help restore a factory-correct, period-correct pedal appearance. Features...

Product#: 3923539

1968-69 327, 350 Carb to Accelerator Lever Rod; Small Block with 4 bbl Carb

Reproduction 1968-69 accelerator pedal rod for 327 or 350 engines with 4 bbl carburetors. This rod is the essential link between the accelerator pedal lever and the carburetor. Each rod is manufactured to correct...

Product#: *R5003

1968-81 GM Pedal Pad and Trim Plate Kit; Disc Brake; Auto Trans; 6 Piece Kit; Various Models

Reproduction of the original pedal pads and pedal pad trim plates to fit various GM models. This pedal pad set is designed to replace the worn out original pads for models equipped with disc brakes and automatic transmission....

Product#: 368077

1967-2002 Buick, Chevrolet, Pontiac, Oldsmobile; Accelerator Pedal Tension Spring; Various Car and Truck Models

This is an OER® reproduction of the original type tension spring that will enable your gas pedal pad to position itself properly. This spring attaches under the pedal pad and attaches to the rod assembly to keep the pedal...

Product#: IN3091G

1964-65 Pontiac GTO, LeMans; Accelerator Pedal; OER Rubber

This pedal is a reproduction of the OEM 1964-65 Pontiac GTO and LeMans. Sold individually. This is a factory style rubber gas/accelerator pedal and is 100% correct.

Product#: 403929

1968-79 Accelerator Control Cable Retainer ; Various Models

OER® reproduction of the correct cable retainer used to hold the accelerator control cable. This retainer slips over the cable and clips into the hole on the accelerator pedal arm. Manufactured in injection molded plastic...

Product#: 368078

1967-2002 Buick, Chevrolet, Pontiac, Oldsmobile; Accelerator Pedal Mounting Pin; Various Car & Truck Models

This special mounting pin is just what you need to correct a loose accelerator pad. This OEM design allows the accelerator pad to attach to the accelerator arm correctly and tightly. Replacing this pin will fix the problems...

Product#: 3863501

1968-74 Buick, Chevrolet, Pontiac, Oldsmobile; Accelerator Pedal Pad to Rod Support

Reproduction of the original style GM accelerator pedal rod support for use on the various Buick, Chevrolet, Pontiac, and Oldsmobile models as listed. Each support is manufactured in injection molded ABS offering an exact...

Product#: K519

1968-69 Camaro, 1968-74 Nova, Omega, Ventura; Accelerator Pedal Assembly; V8; 307ci, 327ci, 350ci, 396ci, 402ci

Reproduction of the complete accelerator pedal assembly which extends from the firewall on all V8-equipped 1967 Firebird models. This accelerator pedal assembly comes complete with the pedal, pedal mount pin and spring,...

Product#: 340637

1974-81 Outer Accelerator Pull Spring

Correct reproduction of the commonly missing or worn out outer accelerator pull spring which mounts between the carburetor and water neck and helps to return the throttle to the closed position. Manufactured to exact factory...

Product#: 3749084

1955-81 Retainer Clip; Trans Control Rod, Clutch Push Rod, Throttle Rod Swivel

OER® reproduction clip for a variety of different parts on 1955-81 GM vehicles. This clip was used to attach the throttle valve control rod, throttle lever rod swivel, and the upper and lower clutch push rods. Use as...

Product#: *R5005

1967-77 GM Pedal Pad Kit With Disc Brake Emblem; Auto Trans; 6-Piece Kit

Reproduction of the original pedal pads designed for 1967-68 Camaro, Firebird and a variety of additional GM models as listed. This pedal pad set is designed to replace the worn out original pads for models with disc brakes...

Product#: 3864742

1964-71 Chevrolet, GMC Car & Truck; Floor Mounted Accelerator Pedal Pad Trim Plate; Various Models

Correct reproduction accelerator pedal pad stainless trim plate for various 1965-71 GM vehicles. Manufactured in stamped stainless steel, this trim plate helps restore a factory-correct, period-correct pedal appearance with...

Product#: *R5002

1968-81 GM Pedal Pad and Trim Plate Kit; Auto Trans; 6 Piece Kit; Various Models

Reproduction of the original pedal pads and pedal pad trim plates to fit various GM models. This pedal pad set is designed to replace the worn out original pads for models equipped with automatic transmission. Replacing the...

Product#: K912

1967-2004 Buick, Chevy, Pontiac, Olds; Accelerator Pedal Pad Trim Plate; Stainless Steel; Various Models

Reproduction of the original accelerator pedal trim plate designed for use on various GM models. Manufactured to exact factory dimensions, this trim plate is stamped in quality stainless steel for a superb, factory-correct...

Product#: *R5004

1967-77 GM Pedal Pad Kit - Auto Trans - 6 Piece Kit

This complete kit is designed to replace pedal pads and trim plates on a variety of Chevrolet models including 1967-68 Camaro with drum brakes and an automatic transmission as well as a variety of additional GM models as...

Product#: *R5009A

1972-81 GM Pedal Pad Kit; Manual Trans; 4 Piece Kit; Various Models

Reproduction of the original pedal pads designed for use on 1976-81 Camaro, Firebird and various other GM models. This pedal pad set is designed to replace the worn out original pads for models with disc brakes and manual...

Product#: *R5019

1970-71 Camaro Z28 Pedal Pad Kit ; Drum Brakes, Auto Trans; 6 Piece Set

Reproduction of the original pedal pads and trim plates for use on 1970-71 Camaro Z/28 models. This complete kit is designed to replace pedal pads and trim plates on 1970-71 Z/28 models with drum brakes and automatic...

Product#: *R5016

1970-71 Camaro Z28 with Disc Brakes and Automatic Transmission; 5-Piece Pedal Pad Kit

This complete kit is designed to replace pedal pads and trim plates on 1970-71 Z28 models with disc brakes and an automatic transmission. Kit includes Accelerator pedal pad Disc Brake pedal pad with the "Disc Brakes" chrome...

Product#: *R5009

1969-71 GM Pedal Pad Kit Manual Transmission; With Disc Brakes Emblem - 8 Piece

Reproduction of the original pedal pads designed for 1969-71 Camaro and 1970-71 Firebird models equipped with 3" brake and clutch pedal. Each pad is manufactured to original factory specs! 8 piece set includes the 3" brake...

Product#: *R1011

1969 Firebird; Pedal Pad Kit; with Stainless Trim; Auto Trans; 6 Piece Set

Reproduction of the original pedal pads with trim designed for 1969 Firebird models. This pedal pad and trim set is designed to replace the worn out original pads for 1969 Firebird models with automatic transmissions....

Product#: *R5007

1967-68 Camaro / Firebird Pedal Pad Kit - Disc Brakes - Manual Trans - 8 piece

Reproduction of the original pedal pads designed for 1967-68 Camaro and Firebird models. This pedal pad set is designed to replace the worn out original pads for models with disc brakes and manual transmissions. Replacing the...

Product#: *R5010

1972-81 GM Pedal Pad Kit - Manual Trans - 8 Piece set

Reproduction of the original pedal pads designed for 1969-71 Camaro and 1970-71 Firebird models equipped with 3" brake and 2-3/8" clutch pedal. Each pad is manufactured to original factory specs! 8 piece set includes the 3"...

Product#: *R5018

1970-71 Camaro Z28 with Disc Brakes and Manual Transmission Pedal Pad Kit - 7 Piece Set

This complete kit is designed to replace pedal pads and trim plates on 1970-71 models with floor mounted gas pedal , drum brakes and a manual transmission. For models with the 3" clutch pedal. To ensure proper fit, measure...

Product#: *R5017

1970-71 Camaro Z28 with Drum Brakes and Manual Transmission Pedal Pad Kit - 7 Piece Set

This complete kit is designed to replace pedal pads and trim plates on 1970-71 models with floor mounted gas pedal , drum brakes and a manual transmission. For models with the 3" clutch pedal. To ensure proper fit, measure...

Product#: *R1010

1969 Firebird; Pedal Pad Kit; Manual Trans; 8 Piece Set

Reproduction of the original pedal pads designed for 1969 Firebird models. This pedal pad set is designed to replace the worn out original pads for 1969 Firebird models with manual transmission. Replacing the pedal pads will...

Product#: MN2227

1968-72 Dodge, Plymouth A-Body Throttle Cable; 19-7/8"; with 273, 318, 340

Reproduction of the original throttle cable designed for use on 1968-72 Dodge and Plymouth A Body models as listed. This reproduction throttle cable is designed for use with 273/318/340 engines. Connects the accelerator...

Product#: 3923549

1965-69 Impala, Bel Air, Chevelle, El Camino, Camaro, Nova; Carb to Accelerator Lever Rod; Big Block 396; with 4 bbl Carb

Reproduction of the original 1968-69 accelerator pedal rod designed for use with 396 engines with 4 bbl carburetors. This rod is the essential link between the accelerator pedal lever and the carburetor. Each rod is...

Product#: MD2144

1971-72 Dodge, Plymouth; Accelerator Pedal Pad and Bezel Kit ; Various Models

Reproduction of the original accelerator pad, bezel and hardware designed for use on Dodge and Plymouth A, B and E-body models. This injection molded ABS accelerator pedal pad set includes the pedal pad, stainless steel...

Product#: 3909978

1967 Chevy, Pontiac; Accelerator Pad; with Steel Backing Plate; OE Style; Various Models

Reproduction of the original accelerator pedal pad designed for use on various 1967 GM models. This accelerator pedal pad is manufactured in the correct design based on a steel backing unlike the GM plastic replacements. The...

Product#: 3923551

1968-69 Camaro Z28 Carb to Accelerator Lever Rod; 302 4 bbl

Reproduction accelerator pedal rod for 1968-69 Camaro Z/28 302 engines with 4 bbl carburetors. This rod is the essential link between the accelerator pedal lever and the carburetor. Each rod is manufactured to correct...

Product#: K0135

1968-80 Chevrolet, Pontiac; Accelerator Return Spring

This is a correct reproduction of the commonly missing or worn out accelerator return spring which mounts between the carburetor and water neck and helps to return the throttle to the closed position. Chevrolet Applications:...

Product#: 14672

1968-72 Camaro, Impala, Nova; Quadrajet Throttle Cable Bracket

Reproduction of the original style Quadrajet throttle cable bracket designed for use with various 1968-72 Chevrolet models. Each cable bracket is manufactured in stamped steel to original factory specifications making this...

Product#: MD1620

1971-74 Mopar Accelerator Pedal Pad Bezel ; Various Models ; Stainless Steel

Reproduction of the original accelerator pedal bezel designed for use on various 1971-72 Reproduction of the original accelerator pad bezel designed for use on Mopar A,B,C-Body and E-Body models. Each accelerator pedal bezel...

Product#: MN2229

1970-74 Challenger, Barracuda, Cuda; Accelerator Throttle Cable; 318, 340, 360; 22-1/2"; OER

Reproduction of the original accelerator throttle cable designed for use on 1970-74 Dodge and Plymouth E body small block (318, 340, 360) models as listed. Each cable is manufactured to correct factory specifications...

Product#: 3577527

1971-72 Mopar Accelerator Pedal Pad ; A,B,C,E-Body

Reproduction of the original accelerator pedal pad designed for use on various Chrysler, Dodge and Plymouth A, B, C, and E-body models. This injection molded ABS pedal pad is an accurate reproduction of the original pad...

Product#: GN110242

1978-88 Buick, Chevrolet Pontiac, Olds; Accelerator Pedal Pad; Various Models

Reproduction of the original accelerator pedal designed for use on various 1978-87 GM G-Body models. Manufactured in injection molded ABS to factory specifications replicating the original in quality and appearance. Will fit...

Product#: *MD2170

1971-72 Mopar A,B,C,E-Body Accelerator Pedal with Hardware

Reproduction accelerator pedal for Dodge and Plymouth A, B, C and E-body models. This injection molded ABS pedal set includes pedal, spring, spacer pad for rear of pedal, and installation pin for a complete replacement of the...

Product#: MD2169

1962-65 Dodge,Plymouth A, B-Body; Accelerator Pad, Floor Mounted

Reproduction of the original accelerator pedal pad designed for use on 1962-65 Dodge and Plymouth models. This quality reproduction is manufactured with an OEM style embedded steel core offering an authentic appearance and...

Product#: 27948

1967-73 Skylark, Riviera, Regal; Accelerator Return Spring; Bracket

This is the factor throttle/accelerator return spring bracket that attaches to the intake and hold returns spring. For various Buick models including Electra, Skylark, Regal, LeSabre. Sold individually. See vehicle fitment...

Product#: HC89

1968 Carburetor Return Spring

Reproduction of the original carburetor return spring for 1968 GM cars with Special/HIPO big block engines. Manufactured in the correct green color. Applications: 1968 Camaro Z28 with 302 or 396 1968 Chevelle SS with 396 exc....

Product#: 3671724

1973-74 Mopar Accelerator Pedal Pad ; B,C,E-Body

Reproduction of the original accelerator pedal for 1973 B, C, and E-Body models. Manufactured with the correct details and grain texture for an authentic appearance. Includes pedal only. Correct for 1973 B, C, E-Body, but...

Product#: *ME1613

1973-74 Mopar B, C, E-Body Accelerator Pedal With Hardware

Reproduction of the original accelerator pedal for 1973-74 Barracuda, 'Cuda and Challenger models. Manufactured with the correct details and grain texture for an authentic appearance. Includes pedal and hardware. Mopar...

Product#: MN2230

1970-74 Challenger, Barracuda, Cuda; Accelerator Throttle Cable; with Hemi; 17-1/2"; OER

Reproduction of the original accelerator throttle cable designed for use on 1970-74 Dodge and Plymouth E body Hemi models. Each cable is manufactured to correct factory specifications replicating the original in design and...

Product#: PY4206

1971-74 Trans-Am Throttle Cables

These throttle cables have the correct ends (carburetor and accelerator pedal) and look very close to the original.

Product#: 3923503

1968-69 Camaro, Nova; Accelerator Throttle Arm V8; 307ci, 350ci, 396ci; w/o Cowl Induction

Reproduction of the original throttle arm designed for use on 1968-69 Camaro and Nova models. Each throttle arm is produced to replicate the original in quality and fit. Replace your worn out or damaged original throttle arm...

Product#: ME1614

1973-74 Dodge, Plymouth; Accelerator Pedal Pad with Bezel and Hardware; Various Models

Reproduction of the original accelerator pedal pad, chrome trim and mnounting hardware designed for use on 1973 Mopar B,C, and E-Body models. Manufactured exactly as original including the correct grain texture for an...

Product#: 3909980

1967-69 Camaro, 1970 Nova; Accelerator Pedal Rod; V8

Reproduction of the original accelerator pedal pad rod designed for use on 1967 Camaro (6 & 8 cylinder), 1968-69 Camaro (8 cylinder), and 1970 Chevy II Nova models. This rod connects between the throttle arm and the...

Product#: 9779969

1965-66 Various Pontiac Models Including GTO, LeMans, Tempest; Tri-Power; Throttle/Accelerator Cable; Mounting Bracket

Reproduction Tri-Power accelerator/throttle cable mounting bracket is a perfect fit for 1965-66 GTO, LeMans, Tempest, Grand Prix and Bonneville with Tri-Power 389 engine. 4 piece kit. See vehicle fitment for complete...