Classic Industries Restoration Parts and Accessories - Accelerator Components

Reproduction of the original carburetor spring designed for use on 1955-57 Chevrolet models with 6 cylinder and automatic transmissions. After you rebuild your original carburetor, be sure to make it perform properly. Don't...

Three piece universal billet aluminum pedal kits from Billet Specialties. This kit comes with easy to use drill templates and the necessary stainless steel hardware for installation. Made in USA Dimensions: Gas Pedal -...

Not only can incorrect throttle return springs hurt the appearance of your vehicle, but they can also be downright dangerous if they do not have the tension and strength that your particular application calls for. Don?t risk...

Reproduction pedal pad kit for 1969-70 Mustang models equipped with an automatic transmission, and drum brakes. Includes brake pad and accelerator pedal pad. Kit includes: Accelerator pedal pad Brake pedal pad Ford...

Correct reproduction of the commonly missing or worn out accelerator return spring designed for use with 1970-72 Camaro models with 396 big block engines. This spring mounts between the carburetor and water neck and helps to...

These throttle cables have the correct ends (carburetor and accelerator pedal) and look very close to the original.

Reproduction accelerator pedal bracket gasket for 1970-74 E-Body models. This foam gasket installs between the pedal bracket and the firewall.

Universal style accelerator throttle rod designed for use on various GM, Ford, Chrysler, Dodge, Plymouth models. This accelerator rod is for use when modifications will not allow the use of the original rod between the...

Throttle cable bracket to hold down. This part holds the throttle cable to the intake bracket.

Reproduction of the original 1968-69 accelerator pedal rod designed for use with 327 or 350 engines with 4 bbl carburetors. This rod is the essential link between the accelerator pedal lever and the carburetor. Each rod is...

This billet aluminum cable bracket from Lokar mount to the side of your TPI intake plenum and allow you to install your Throttle, Kickdown, and Cruise Control cable. Made in USA

Correct support assembly which supports the accelerator rod through the firewall. Each support is designed and manufactured to replace the craked or missing original. For use on various GM applications. Applications:...

Black Billet Aluminum. Single Hole Stud For Throttle Cable Only. Lokar throttle cable brackets are available for a variety of different motors including carbureted set ups, LS1, Ram Jet 350 & 502 and more. Carburetor...

Reproduction of the carburetor accelerator found on all 1967 Firebirds with V8 engines. This rod which includes the swivel was used on both 2 and 4 barrel models.

Reproduction of the original throttle arm designed for use on 1968-69 Camaro models. Each throttle arm is produced to replicate the original in quality and fit. Replace your worn out or damaged original throttle arm with this...

These aluminum pedal covers are unique to the market as they actually bolt-on to your pedal instead of clamping on like most aftermarket pedal covers. Manufactured with a hard coat black anodized inner and a brushed aluminum...

This universal throttle cable mounting bracket (also known as a throttle valve cable correction bracket) attaches to the rear left ear of the carburtetor. Designed to work with MN2236 Torqueflite kickdown cable set or as a...

Quality manufactured throttle cable mounting bracket for 440 4bbl applications. Now you can stop scouring swap meets and salvage yards for this hard-to-find part. Each bracket comes complete with hold down and features...

Reproduction of the original pedal pads designed for use on 1976-81 Camaro, Firebird and various other GM models. This pedal pad set is designed to replace the worn out original pads for models with disc brakes and manual...

This custom spoon rod style accelerator pedal will provide a fair amount of style to your car's throttle pedal, or go pedal, if you prefer. The pedal is triple chrome plated to a shiny finish. It weighs 10 ounces and ships...

The Eliminator floor-mount gas pedal is precision crafted from billet aluminum and designed to eliminate routing cables through the firewall. Includes an adjustable aluminum splined shaft and stainless steel under-the-floor...

Reproduction of the original throttle linkage designed for use 1955-59 V8 Chevrolet and GMC trucks. Manufactured to OE specifications and zinc plated for long lasting dependibility. Goes from the accelerator pedal, through...

Replacement throttle return spring bracket to fit a 1971-73 340 or 360 engine with 4 barrel carburetor built through April, 1973. Now you can stop scouring swap meets and salvage yards for this hard to find bracket and pick...

Dress up your interior with these high quality brushed aluminum pedal covers. Unlike other covers on the market these are a two piece design that are bolted through your factory pedals instead of being held on with clamps. ...

Reproduction of the original accelerator pedal pad, chrome trim and mnounting hardware designed for use on 1973 Mopar B,C, and E-Body models. Manufactured exactly as original including the correct grain texture for an...

This Lokar® billet aluminum throttle pedal assembly is made to bolt into the factory mounting location on the firewall without any drilling or modification and is designed with an internal spanner nut to maintain perfect...

Replacing your pedal pads will renew the appearance of your interior while maintaining originality. Accelerator pedal pad is manufactured to exact factory specifications featuring correct ribs and polished trim. Brake pedal...

Replacement throttle return spring bracket for a 440 six pack engine. Now you can stop scouring swap meets and salvage yards for this hard-to-find bracket and pick up a correct replacement bracket from Classic Industries®....

Reproduction of the original factory style accelerator pedal to firewall seal. Replacing the old or worn out original will help insure the seal between the acccelerator pedal and the firewall is secure. Manufactured in OE...

Edelbrock throttle, cruise control, and transmission kick down set for pre-1978 small block Chevy cars with a TH350, 200R4, or 700R4 transmission. Manufactured in stamped steel and either chrome or gold cadmium plated....

Billet pedal cover sets for 1967-69 Camaro models. Pedal covers are CNC machined from a solid piece of aluminum to fit the curve of your pedals and include parking brake pedal cover.

Reproduction of the original accelerator shaft to pedal spring that mounts to the accelerator pedal arm maintaning tension on the pedal. Manufactured from spring steel to ensure proper fit and function. Designed for use on...

Reproduction of the original pedal pads designed for 1967-68 Camaro, Firebird and a variety of additional GM models as listed. This pedal pad set is designed to replace the worn out original pads for models with disc brakes...

This billet aluminum cable bracket from Lokar mounts to the side of your TPI intake plenum and allow you to install your throttle cable. Made in USA Black billet aluminum. Single hole stud for throttle cable only.

Dress up your interior with these high quality brushed aluminum pedal covers. Unlike other covers on the market these are a two piece design that are bolted through your factory pedals instead of being held on with clamps. ...

Reproduction cruise control servo bellows for 1967-72 Firebird models. Replacing your leaky servo bellows should be the first step in repairing a non-functional cruise control system. Manufactured using the correct rubber...

The Edelbrock throttle bracket was designed for the Pontiac Firebird utilizing Edelbrock intake manifold part # 2156, 5056, 7156 or 3756. This kit makes hooking up your throttle a simple task. It's comprised of the correct...

This throttle rod adapter removes the guesswork when installing a Street Demon carburetor using mechanical linkage in almost any carbureted GM application. All brackets have a clear zinc coating for corrosion protection and...

Reproduction of the original accelerator pedal mounting hardware designed for use on 1973-74 Mopar B, C and E-Body models. These components are used used to attach the accellerator pedal pad. Includes the pedal tension...

Lokar 1962-67 Nova billet aluminum throttle pedal assembly is designed to bolt into the stock location on the firewall, allowing you to change from the factory rod linkage to a modern throttle cable set up. The traditional...

Reproduction of the original accelerator pedal pad rod designed for use on Camaro and Nova models. This rod connects between the throttle arm and the accelerator pedal. Manufactured in correct configuration, replaces the bent...

Not only can incorrect throttle return springs hurt the appearance of your vehicle, but they can also be downright dangerous if they do not have the tension and strength that your particular application calls for. Don?t risk...

Dress up your interior with these high quality brushed aluminum pedal covers. Unlike other covers on the market these are a two piece design that are bolted through your factory pedals instead of being held on with clamps. ...

Reproduction of the original gas pedal throttles and hardware designed for use with 1968-69 Camaro models. Each set includes the gas pedal arm, bushing, throttle arm, and grommet for a complete replacement of the throttle. 5...

This beautifully carved brushed billet aluminum throttle assembly has a spring-loaded pad like the OE design and features a splined removable lower arm for versatility in mounting to the right or left of the bracket. The...

Replacement throttle return spring bracket to fit a 426 Hemi engine with dual four barrel carburetor applications. Now you can stop scouring swap meets and salvage yards for this hard-to-find bracket and pick up a correct...

Manufactured from solid billet aluminum, this black anodized custom pedal assembly set includes a throttle pedal assembly paired with a matching brake pedal cover. The billet throttle pedal assembly is fully adjustable,...

Not only can incorrect throttle return springs hurt the appearance of your vehicle, but they can also be downright dangerous if they do not have the tension and strength that your particular application calls for. Don?t risk...

Lokar direct fit pedal pads for use with Lokar?s drive-by-wire throttle control assembly. The standard model measures 4" x 1-1/2" and the XL model measures 5" x 2". Both sizes are available in brushed and black finishes to...

These CNC machined pedal pads are specifically designed to compliment your Billet Specialties gas pedal. Each pad includes all the stainless steel hardware needed for a quick and clean install. Note: Replaces factory pad.

OER® reproduction of the original accelerator rod grommet and sleeve unit where the accelerator rod fits into the linkage. This grommet often deteriorates due to engine heat or chemical spillage. Replacing the grommet will...

Correct OER® reproduction of the original floor mounted accelerator pedal pad installed on various GM models. Each accelerator pedal pad is manufactured in quality hard EPDM rubber unlike the plastic service replacement...

Replacement accelerator pedal bezel for various 1967-70 Mopar A-Body models. Features the correct stainless steel finish.

Not only can incorrect throttle return springs hurt the appearance of your vehicle, but they can also be downright dangerous if they do not have the tension and strength that your particular application calls for. Don?t risk...

Reproduction of the original accelerator assembly designed for use with 6 cylinder or dual carburetor Camaro models. Extends from the firewall and comes with the accelerator pedal, pedal mount pin and spring, accelerator rod,...

Lokars traditional flat style billet aluminum throttle pedal pad lets you retain the factory throttle linkage, with a updated look inside the car. The direct fit throttle pad replaces the factory pad, measures 2" x 5" and...

Correct reproduction of the original accelerator pedal designed for use with 1955-57 Chevrolet Bel Air, 150, 210, and Nomad models. Each pad is manufactured to correct factory specifications replicating the original in design...

These CNC machined pedal pads are specifically designed to compliment your Billet Specialties gas pedal. Each pad includes all the stainless steel hardware needed for a quick and clean install.

Reproduction of the original throttle cable designed for 1967-76 Mopar A-Body models with 383 or 440 engines. This cable connects the accelerator linkage to the carburetor. Each cable will fit and install as original. ...

This is the retainer bracket which holds the rear loop of the throttle return spring in place. This bracket which mounts on top of the coil bracket was used on 1968-70 Camaro models with a small block engine and Rochester...