Classic Industries Restoration Parts and Accessories - Differential Hardware

Eliminate those pesky leaks that 9" Ford housings are known for. This breather vent for hose is for use with the breather tank (sold separately). Made in USA Note: Special order, must be prepaid. Non-returnable....

FilterMag’s powerful rare-earth magnet trap and hold wear inducing metal particles smaller than 40-microns down to 1-micron. The super-strong magnetic force holds FilterMag to the cover, is reusable and will reduce...

This set supplies all of the polyurethane bushings and bolt sleeves that you need to do all three (3) rear differential to rear cradle mounts on your 2010-15 Camaro. Manufactured to help eliminate wheel hop and rear...

Replacement thrust spacer set for 8-3/4" differentials with clutch type Sure-Grip prior to 1970. Required to provide axle thrust surface in four-spider differential applications. One set required per vehicle.

Reproduction 8 3/4” differential nuts for use with 1968-69 B-body models. These nuts feature a nylon patch which increases the metal to metal contact even under heavy vibration. Sold in sets of 10. Plymouth Applications:...

This 1967-1979 Corvette Differential Bearing Spacer is a genuine GM replacement part. The corresponding GM part number is 9780883. It is comprised of steel and ships via UPS. Specific fitment includes: 1967-1979 Corvette

Eliminate those pesky leaks that 9" Ford housings are known for. This "catch can" mounts above the housing. Excess pressurized gear oil goes to the tank, is vented and drains back after parking the car. Made in USA Note:...

Work on your differential third member safely and easily with this lightweight fixture. It can be clamped or bolted to your work bench or simply mounted in a vise, and it fits neatly in your tool chest when the job is...

Special plated bolts to complete the installation of your chrome rear end cover. Fits both 10 or 12 bolt covers. Sold as a set of 12.

Differential carrier spring kit replacement part for the LR1910 12-bolt PowerTrax Locking Differential. NOTE: One (1) required per vehicle Applications: 1967-70 Camaro with 12-bolt reare nd

New reproduction 3/8" hex flange bolts for use with 1968-69 Dodge and Plymouth models. Set includes 10 bolts total and fits several vehicles. See description below to ensure a proper fit on your Mopar. Dodge Applications:...

Mopar 8-3/4" "89" case housing

The Camaro Z/28 is equipped with an RDM cooling system that circulates cooled transmission fluid through a heat exchanger integrated into the rear end cover. This innovative system reduces oil temperature by over 100°F...

This GM Differential Clutch Disc Repair Kit is a genuine GM replacement part. The corresponding GM part number is 231127. The repair kit is for a GM 8.5-inch, 10-bolt positraction differential with 28 splines. It is comprised...

This is a differential side gear thrust washer. It's a genuine General Motors replacement part. The corresponding GM part number is 3846425. The steel component weighs one ounce and ships via UPS. Applications: 1962-1970...

This GM 12 Bolt Posi Differential Clutch Disc Guide is a genuine GM replacement part. The corresponding GM part number is 9778355. This component is comprised of steel and comes as a set of four guides. It is used in GM...

Chrome differential cover bolts for Dana 60 rear axles. Each set includes enough bolts to mount the differential cover to the axle housing.

This forged steel yoke is manufactured specifically for Mopar differentials. Includes the yoke, and mounting hardware. Important: Use MM3310 strap kit, Note: Uses 1350 series U-joint (sold separately) that have a 3.625"...

This chrome moly billet yoke is manufactured specifically for Mopar differentials. Includes the yoke, u-bolt, and mounting hardware. Note: Uses 7260 series U-joint (sold separately) that have a 2.125" snap ring sp an with a...

This billet steel yoke is manufactured specifically for Mopar differentials. Includes the yoke, and mounting hardware. Important: Use MM3307 u-bolt kit, Note: Uses 1350 series U-joint (sold separately) that have a 3.625"...

This billet steel yoke is manufactured specifically for Mopar differentials. Includes the yoke, and mounting hardware. Important: Use MM3307 u-bolt kit, Note: Uses 1350 series U-joint (sold separately) that have a 3.625"...

This cast iron yoke is manufactured specifically for Mopar differentials. Includes the yoke, and mounting hardware. Important: Use MM3311 s trap kit, Note: Uses 7260 series U-joint (sold separately) that have a 2.125" snap...

This chrome moly billet reproduction yoke is manufactured specifically for Mopar differentials. Includes the yoke, u-bolt, and mounting hardware. Note: Uses 7290 series U-joints (sold separately) that have a 2.62 5" snap...

Aftermarket replacement now available for 12 bolt models. The shim kit includes the correct size pinion shims for 12 bolt applications. Set Includes 10 shims that measure 2.25" O.D. and 1.65" I.D. Shim thickness: 3 - ....

Chrome differential cover bolts for 8-1/4" rear axles. Each set includes enough bolts to mount the differential cover to the axle housing.s

Replacement crush sleeve for setting up your rear axle. Crush sleeves cannot be reused if you are changing a ring and pinion or the front seal. Includes pinion nut washer and pinion flange nut. These are for the 9-1/4"...

Original factory style bolt used to attach the differential cover to the differential on models with either a 10 bolt or 12 bolt rear end and features the correct original head markings. Each bolt has the correct "RBW" on the...

This dress-up differential cover bolt set features a Pontiac Arrowhead logo stamped directly onto the head of the stainless steel bolts. Stainless Steel 10 Bolt. 5/16"-18 X 3/4 " Perfect for stock or chrome covers. What...

This set is for use on Dana 60, or any other rear end using 3/8"-16 x 3/4" bolts. Includes 12 chrome finished bolts and 12 Flat washers (not chromed).

Mopar 8-3/4" or 9-1/4" with "41" or "89" case housing

This set is designed to replace the differential bearings. Includes: Front and rear pinion bearing Pinion seal Carrier bearings Pilot bearing (depending on application) Gear marking compound Crush sleeve Pinion nut ...

This set is designed to replace the differential bearings on models with a 12 bolt differential. Basic bearing set includes bearings and races, gasket (or RTV silicone), washers, and nuts for a complete replacement. ...

Aftermarket replacement now available for 12 bolt models. The shim kit includes the correct size pinion shims for 12 bolt applications. Set Includes 5 shims that measure 2.25" O.D. and 1.45" I.D. Shim thickness: .010"s him...

Used in Dana 60 9 3/4" differentials with clutch type Sure-Grip from 1966-70. Required to provide axle thrust surface in four-spider differential applications. Exact replicas of original parts. Heat treated for long life...

This set is designed to replace the differential bearings on 1970-81 Camaro models. Basic bearing set includes bearings and races, gasket (or RTV silicone), washers, and nuts for a complete replacement.

It is very important that you verify that your cross shaft has been properly hardened, prior to installation. Simply take a file and attempt to scratch a cut or groove near the center of the shaft. If you have a properly...

This set is designed to replace the differential bearings on 1967-70 Camaro models. Master bearing set includes bearings and races, gasket (or RTV silicone), washers, nuts and ring gear bolts for a complete replacement.

Authentic reproduction of the Differential Vent Valve for 1964-77 Oldsmobile, and 1954-73 Buick models as listed. Located at the top of the differential housing, this valve is found on a wide variety of vintage GM models. ...

This set is designed to replace the differential bearings on 1970-81 Camaro models. Master bearing set includes bearings and races, gasket (or RTV silicone), washers, nuts and ring gear bolts for a complete replacement.

This set is designed to replace the differential bearings on 1967-72 Camaro models. Basic bearing set includes bearings and races, gasket (or RTV silicone), washers, and nuts for a complete replacement.

This differential cross shaft is for certain high numeric ratio gear sets that require special notched cross pins for proper installation. This particular cross shaft is for use with 12-bolt lock right differentials that are...

This set is designed to replace the differential bearings on 1967-70 Camaro models. Basic bearing set includes bearings and races, gasket (or RTV silicone), washers, and nuts for a complete replacement.

This set is designed to replace the differential bearings on 1967-72 Camaro models. Master bearing set includes bearings and races, gasket (or RTV silicone), washers, nuts and ring gear bolts for a complete replacement.

This set is designed to replace the differential bearings on 1967-70 Camaro models. Super master bearing set includes differential bearings and races, gasket (or RTV silicone), washers, nuts, ring gear bolts, rear axle...

BMR Differential Bushings minimize power robbing differential movement by replacing the OE soft rubber bushings with high durometer 4-piece polyurethane bushings. The 95 durometer polyurethane bushings effectively minimize...

Eliminate differential movement and maximize driveline response in your high-horsepower Gen5 Camaro with a set of Delrin Differential Bushings from BMR Suspension. These bushings are CNC-machined from Delrin plastic which is...

This set is designed to replace the differential bearings on 1967-72 Camaro models. Super master bearing set includes differential bearings and races, gasket (or RTV silicone), washers, nuts, ring gear bolts, rear axle...

This set is designed to replace the differential bearings on 1970-81 Camaro models. Super master bearing set includes differential bearings and races, gasket (or RTV silicone), washers, nuts, ring gear bolts, rear axle...

Enhance the appearance of your rear end with ARP's stainless steel rear cover bolts. These bolts add a lustrous contrast to a painted OEM cover, compliment a chrome plated aftermarket version or add flash to that cast...

BMR Differential Bushings minimize power robbing differential movement by replacing the OE soft rubber bushings with high durometer 4-piece polyurethane bushings. The 68 durometer polyurethane bushings effectively minimize...

This set is designed to replace the differential bearings on 1963-87 1/2 ton Truck models. This kit uses Timken bearings and races along with high quality seals and small parts. Included in this kit are carrier bearings and...

This set is designed to replace the differential bearings on 1958-64 Chevrolet full size models. Basic bearing set includes bearings and races, gasket (or RTV silicone), washers, and nuts for a complete replacement.

This is a rear axle shim kit for General Motors automobiles. It fits General Motors vehicles that were sold in the U.S., Europe, and the UK. It's a genuine General Motors part with an OEM part number of 3853762. The shims are...

This dress-up differential cover bolt set features a SS logo stamped directly onto the head of the chrome plated bolts. Perfect for stock or chrome covers. What better way to make a statement than with these unique bolts?

This dress-up differential cover bolt set features a flame logo stamped directly onto the head of the chrome plated bolts. Perfect for stock or chrome covers. What better way to make a statement than with these unique...

This dress-up differential cover bolt set features a 350 logo stamped directly onto the head of the chrome plated bolts. Perfect for stock or chrome covers. What better way to make a statement than with these unique bolts?

This dress-up differential cover bolt set features a 350 logo stamped directly onto the head of the chrome plated bolts. Perfect for stock or chrome covers. What better way to make a statement than with these unique bolts?